Introduction
The HUTT W66 is an intelligent automatic window cleaning robot designed for efficient wet and dry glass cleaning. Featuring an exclusive water spray system, intelligent route planning, and powerful suction, it simplifies window maintenance. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your device.
Package Contents
Please check the box for the following items:
Figure 1: Included Accessories
- Host Machine (HUTT W66 Robot)
- Cleaning Rags (multiple pieces)
- Remote Control
- Battery (for remote control, if applicable, or internal robot battery)
- Power Plug
- Adapter
- Measuring Bottle (for water/cleaning solution)
- Instruction Manual (this document)
- Quick Use Guide
Setup
Initial Charging
Before first use, ensure the HUTT W66 robot is fully charged. Connect the power adapter to the robot and a power outlet. The charging indicator will show the charging status.
Attaching Cleaning Rags
Attach the provided microfiber cleaning rags to the bottom of the robot. Ensure they are securely fastened to cover the cleaning surfaces.
Filling the Water Tank
Locate the water tank cap on the robot. Use the measuring bottle to fill the 150ML intelligent control water tank with clean water or a non-corrosive glass cleaning solution. Close the cap securely.
Figure 2: Water Tank and Spray Nozzles
Safety Rope Attachment
For safety, especially when cleaning high windows, always attach the safety rope to the robot and secure the other end to a sturdy fixture indoors. This prevents the robot from falling in case of power loss or detachment.
Placement on Window
Place the robot on the glass surface you wish to clean. Ensure the surface is relatively clean of large debris to prevent scratching. The robot will automatically adhere to the glass using its suction.
Operating Instructions
Powering On/Off
Press the power button on the robot or the remote control to turn the device on. To turn off, press and hold the power button until the robot detaches or powers down.
Starting Cleaning
Once powered on and securely attached, press the "Start" button on the robot or remote control. The HUTT W66 will initiate its intelligent route planning and begin cleaning.
Figure 3: Intelligent Route Planning
Intelligent Water Spray
The robot features an exclusive water spray design. It will automatically spray water every 10 seconds for even coverage, ensuring the cleaning rags maintain optimal humidity for effective cleaning. The water tank capacity allows for cleaning approximately 70-80 square meters of glass per fill.
Figure 4: 8-Point Water Spray System
Automatic Frequency Conversion Suction
The HUTTTHINK smart algorithm allows the W66 to automatically adjust its suction power based on the glass cleanliness. It increases pressure for dirtier areas and decreases it for lighter cleaning, optimizing efficiency and cleaning performance.
Figure 5: High Suction Power
Edge Detection and Obstacle Avoidance
Equipped with laser detection sensors, the robot can accurately identify window edges and obstacles. It will automatically slow down and repeatedly wipe the edge glass, ensuring thorough cleaning while avoiding hazards, even on borderless glass.
Figure 6: Laser Detection Sensor
Completion of Cleaning
Upon completing its cleaning cycle, the robot will automatically return to its starting position and may emit an audible alert. Carefully remove the robot from the glass surface.
Maintenance
Cleaning the Robot Exterior
After each use, wipe the exterior of the robot with a dry or slightly damp cloth to remove any dust or residue. Do not use abrasive cleaners or immerse the robot in water.
Cleaning/Replacing Cleaning Rags
Remove the microfiber cleaning rags from the robot. They can be hand-washed or machine-washed with mild detergent. Ensure they are completely dry before reattaching for the next use. Replace worn-out rags as needed for optimal cleaning performance.
Water Tank Maintenance
Regularly empty and rinse the water tank to prevent residue buildup. If using cleaning solutions, ensure they are non-corrosive to avoid damage to the internal spray system.
Track Maintenance
Inspect the non-slip special tracks for any debris or wear. Clean them gently with a soft brush if necessary to maintain optimal grip on glass surfaces.
Figure 7: Multi-layer Composite Track
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Robot does not adhere to glass. | Low suction power; dirty cleaning rags; uneven surface. | Ensure power is connected. Clean or replace rags. Ensure glass surface is flat. |
| Water spray not working. | Empty water tank; clogged nozzles. | Refill water tank. Clean spray nozzles gently. |
| Robot stops unexpectedly. | Power interruption; internal error. | The robot has UPS power failure protection and can operate for 20 minutes after power loss. Check power connection. If problem persists, contact support. |
| Cleaning performance is poor. | Dirty rags; insufficient water/solution; extremely dirty glass. | Replace or clean rags. Ensure water tank is filled. Pre-clean heavily soiled areas manually. |
Specifications
| Feature | Specification |
|---|---|
| Brand | HUTT |
| Model | W66 |
| Power | 90W |
| Voltage | 100-240V |
| Cord Length | 6M |
| Battery Capacity | 650mAh |
| Vacuum Suction | 2600Pa |
| Product Size | 23.1 x 23.1 x 7.6 cm |
| Product Weight | 1.57 kg |
| Material | ABS |
| Certification | CE |
Figure 8: Product Dimensions
Figure 9: Internal Components
User Tips
- For best results, ensure the water tank is always filled with water or a suitable cleaning solution before starting a cleaning cycle.
- Regularly clean or replace the microfiber rags to maintain optimal cleaning efficiency and prevent streaks.
- The robot's laser sensors are designed to detect edges, even on frameless glass. Trust its intelligent navigation.
- In case of a power outage, the built-in UPS battery provides up to 20 minutes of backup power, allowing you to safely retrieve the robot.
- For extremely dirty windows, a preliminary manual wipe might be beneficial before using the robot to prevent excessive strain and ensure a spotless finish.
Warranty and Support
Warranty Information
The HUTT W66 Window Cleaning Robot comes with a two-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. If any damage occurs that is covered under warranty, replacement parts will be provided free of charge, along with installation guidance (e.g., video instructions).
Please note that this warranty does not cover damage caused by artificial misuse, accidents, unauthorized modifications, or improper maintenance. In such cases, repair services may be available for a fee.
Customer Support
For technical assistance, warranty claims, or any questions regarding your HUTT W66, please contact your retailer or the official HUTT customer service. Refer to your purchase documentation for specific contact details.
