FlySky FS-iA6, FS-iA6B, FS-iA10B, FS-X6B Receiver

Contents

FlySky RC Receiver Instruction Manual

Models: FS-iA6, FS-iA6B, FS-iA10B, FS-X6B

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your FlySky RC receivers, including models FS-iA6, FS-iA6B, FS-iA10B, and FS-X6B. These receivers are designed for various RC applications such as airplanes, gliders, helicopters, and FPV drones, utilizing the reliable AFHDS 2A (Automatic Frequency Hopping Digital System) protocol.

Overview of FlySky FS-X6B, FS-iA10B, FS-iA6, and FS-iA6B receivers
Figure 1: Overview of various FlySky receiver models.

Specifications

Below are the detailed specifications for each receiver model:

FlySky FS-iA6 Receiver

FeatureSpecification
Channels6
Frequency Range2.4-2.48 GHz
Number of Bands140
Transmitting Power≤ 20dBm
Receiver Sensitivity-105dBm
2.4G ModesAFHDS 2A (Automatic Frequency Second Generation Digital Systems)
EncodingGFSK
Input Power4.0-6.5V DC
i-BUS InterfaceNo
Data Acquisition InterfaceNo
CertificationCE0678, FCC
UsageRC Airplane / Glider / Helicopter
Compatible TransmittersFlysky FS-i10, FS-i6, FS-i4, FS-GT2F, FS-GT2E, FS-GT2B
FlySky FS-iA6 receiver with bind plug
Figure 2: FlySky FS-iA6 receiver with included bind plug.

FlySky FS-X6B Receiver

FeatureSpecification
Size37 x 22 x 7mm (1.4 x 0.9 x 0.3 inches)
Weight5g (0.18 ounce)
Channels6 (PWM output), up to 18 (i-BUS)
ProtocolAFHDS 2A
AntennaDual omnidirectional
PortsPWM signal (Channels 1-6), PPM signal, i-BUS signal, Voltage sensor (1S-4S connector, 0 to +18V)
Compatible TransmittersAll AFHDS 2A Transmitters (e.g., FS-i10, FS-i8, FS-i6, FS-i6S, FS-i6X, FS-i4, FS-i4X)
Top view of FlySky FS-X6B receiver module
Figure 3: Top view of the compact FlySky FS-X6B receiver module.

FlySky FS-iA6B Receiver

FeatureSpecification
Channels6
Frequency Range2.4055-2.475GHZ
Band Width Number140
Transmitting Power≤ 20dBm
RF Receiver Sensitivity-105dbm
2.4G ModeAFHDS 2A (Enhanced Automatic FM Digital System)
EncodingGFSK
Antenna Length26mm * 2 (dual antenna)
Input Power4.0-8.4V DC
Dimension47 x 26.2 x 15mm
Weight7g
i-Bus InterfaceYes
Data Acquisition InterfaceYes
Model TypeAirplane / Glider / Helicopter
Compatible TransmittersFS-i4, FS-i6, FS-i10, FS-GT2G, FS-GT2E Transmitters
Side view of FlySky FS-iA6B receiver
Figure 4: Side view of the FlySky FS-iA6B receiver.

FlySky FS-iA10B Receiver

FeatureSpecification
Channels10
Frequency Range2.4055-2.475GHz
RF Channel140
RF Receiver Sensitivity-105dBm
Bandwidth500KHz
2.4GHz SystemAFHDS 2A
Modulation TypeGFSK
Power4.0-6.5V DC
Antenna Length26mm (Dual Antenna)
Weight17.6g
Size50.6 x 34.9 x 14.9mm
i-BUS PortYes
Data Acquisition PortYes
Compatible TransmittersFS-I4, FS-I6, GT2E, GT2G, FS-I10, FS-I6S, TH9X, FS-CT6B, GT3C, CT3C, FS-I4, FS-IT4S Transmitters
Side view of FlySky FS-iA10B receiver
Figure 5: Side view of the FlySky FS-iA10B receiver.

Transmitter Compatibility Chart

Transmitter compatibility table for FlySky receivers
Figure 6: Detailed compatibility chart for various FlySky transmitters and receivers.

Package Contents

Depending on the specific model purchased, your package may include:

  • 1x Flysky FS-iA6 receiver
  • 1x Flysky FS-X6B receiver
  • 1x Flysky FS-iA6B receiver
  • 1x Flysky FS-iA10B receiver
  • 1x Bind plug (for FS-iA6B and FS-iA10B)
  • 4x Cables (for FS-X6B)
FlySky FS-X6B receiver module with cables
Figure 7: FS-X6B receiver module with included cables.

Setup Instructions

1. Connecting the Receiver

Connect the receiver to your flight controller or servos according to your model's wiring diagram. Ensure correct polarity (GND, VCC) and channel assignments (CH1-CH6/10, PPM, i-BUS).

  • PWM Signal Ports (FS-iA6, FS-iA6B, FS-iA10B): Connect individual servos or ESCs to the corresponding channel pins (CH1-CH6/10).
  • PPM Signal Port (FS-X6B, FS-iA6B, FS-iA10B): For flight controllers supporting PPM, connect the PPM output to the designated input on your flight controller.
  • i-BUS Signal Port (FS-X6B, FS-iA6B, FS-iA10B): For flight controllers supporting i-BUS, connect the i-BUS output to the designated input. This allows for up to 18 channels on the FS-X6B.
  • Voltage Sensor Port (FS-X6B): Connect an external power sensor (1S-4S connector) to monitor voltage (0 to +18V).
FlySky FS-iA6 receiver showing channel ports
Figure 8: FS-iA6 receiver with clearly labeled channel ports.

2. Binding the Receiver to your Transmitter

To establish communication between your FlySky receiver and transmitter, follow these binding steps:

  1. Ensure your transmitter is powered off. Refer to your transmitter's user manual for specific binding preparation instructions.
  2. Connect the bind plug (if included with your receiver model, e.g., FS-iA6B, FS-iA10B) to the B/VCC port on the receiver. For FS-X6B, locate the 'BIND' button.
  3. Power on the receiver. The receiver's LED should start flashing, indicating it has entered bind mode.
  4. While the receiver is in bind mode, power on your transmitter.
  5. The transmitter should automatically detect and bind with the receiver. Once successfully bound, the receiver's LED will stop flashing and remain solid.
  6. Power off both the transmitter and receiver.
  7. Remove the bind plug from the receiver (if used).
  8. Power on the transmitter first, then the receiver. Verify that all channels respond correctly to transmitter inputs.

If binding is unsuccessful, restart the procedure from the beginning. Ensure your transmitter is compatible with the receiver's AFHDS 2A protocol.

FlySky FS-X6B receiver module with bind button and update port
Figure 9: FS-X6B receiver module highlighting the bind button.

Operating Instructions

Once the receiver is successfully bound to your transmitter and connected to your RC model, follow these general operating guidelines:

  • Always power on your transmitter first, then your RC model (receiver).
  • Always power off your RC model (receiver) first, then your transmitter.
  • Perform a range check before each flight or operation, especially in new environments.
  • Ensure all control surfaces and functions respond correctly and smoothly to transmitter inputs.
  • Avoid operating your RC model in areas with high electromagnetic interference, which can affect signal reliability.
  • Keep the receiver antennas clear of carbon fiber, metal, or other conductive materials that can shield the signal. Position antennas at a 90-degree angle to each other for optimal reception.

Maintenance

Proper maintenance will ensure the longevity and reliable performance of your FlySky receiver:

  • Keep the receiver clean and free from dust, dirt, and moisture.
  • Avoid exposing the receiver to extreme temperatures or direct sunlight for prolonged periods.
  • Regularly inspect antenna wires for any damage or kinks. Replace if necessary.
  • Ensure all connections to the receiver (servo leads, power, data) are secure and free from corrosion.
  • Store the receiver in a dry, cool place when not in use.

Troubleshooting

If you encounter issues with your FlySky receiver, refer to the following troubleshooting tips:

  • No Signal/No Response:
    • Check if the receiver is correctly bound to the transmitter (solid LED on receiver).
    • Ensure the receiver is receiving adequate power (within specified voltage range).
    • Verify all connections between the receiver, flight controller, and servos are secure.
    • Confirm transmitter and receiver are compatible (refer to compatibility chart).
  • Intermittent Signal/Range Issues:
    • Check antenna placement. Ensure they are not shielded by carbon fiber or metal and are oriented at 90 degrees to each other.
    • Perform a range check.
    • Avoid operating near strong interference sources (e.g., Wi-Fi routers, high-power electrical lines).
  • Incorrect Channel Response:
    • Verify channel assignments in your flight controller or servo connections.
    • Check transmitter settings for correct channel mapping.

User Tips

  • Initial Testing: After installation and binding, always perform thorough bench testing before operating your RC model. This ensures all components are functioning as expected.
  • Compatibility Check: Before purchasing or attempting to connect, always verify that your specific transmitter model is compatible with the receiver. Refer to the provided compatibility chart and your transmitter's manual.
  • Wiring Precision: Pay close attention to wiring, especially when connecting to complex systems like flight controllers or custom RC models (e.g., excavators). Incorrect wiring can lead to damage or malfunction.
  • Antenna Placement: Optimal antenna placement is crucial for reliable signal reception. Experiment with different orientations to find the best setup for your model, ensuring they are away from conductive materials.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the official FlySky support channels. Keep your proof of purchase for any warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.