Flysky PL18 EV

Contents

Flysky Paladin PL18 EV Radio Transmitter User Manual

Model: PL18 EV

1. Introduction

The Flysky Paladin PL18 EV is an advanced 18-channel 2.4G radio transmitter designed for RC engineering vehicles, simulation ships, and FPV racing drones. It features the AFHDS 3 protocol, a 3.5-inch HVGA TFT touch screen, and supports various receivers including FS-FGr12B and FGR8B with i-BUS/S.BUS/PPM/PWM data interfaces. This system offers precise control, extensive customization options, and robust anti-interference capabilities, ensuring a reliable and enjoyable remote control experience.

2. Package Contents

Please check the contents of your package carefully. Depending on the version purchased, the contents may vary.

Flysky Paladin PL18 EV Transmitter and included accessories for Standard Version

Figure 2.1: Flysky Paladin PL18 EV Transmitter and accessories (Standard Version shown).

2.1 Standard Version

  • 1x PL18EV transmitter with 301 high frequency + high frequency fixing plate + thin hand glue
  • 1x FGR12B receiver
  • 1x Quick Operation Guide
  • 1x Micro USB cable
  • 1x LOGO sticker 1 (pure logo)
  • 1x LOGO sticker 2 (with other designs)
  • 1x PL18 body sticker

2.2 Ultimate Edition

  • 1x PL18EV transmitter with 301 high frequency + high frequency fixing plate + thin hand glue + large hand glue
  • 1x FGR12B+FGr8B receiver + cable
  • 1x wireless charging dock
  • 1x Quick Operation Guide
  • 1x Micro USB cable
  • 3x Toggle switch rubber cover
  • 1x tray (with hand rest)
  • 1x Tray strap
  • 1x LOGO sticker 1 (pure logo)
  • 1x LOGO sticker 2 (with other designs)
  • 1x PL18 body sticker

3. Specifications

3.1 PL18EV Transmitter Specifications

FeatureDetail
BrandFlySky
Product ModelPL18EV
Product NamePaladin EV
Channels18
Adaptable ReceiversAll AFHDS 3 receivers
Model TypeEngineering vehicles, simulation ship etc.
RF2.4GHz
RF Power<20 dBm
2.4GHz ProtocolAFHDS 3
Distance>300m (open without interference ground)
Channel Resolution4096
Battery1S(3.7V) 4300mAh (built-in)
Charging InterfaceMicro USB/wireless charging
Charging Time4h@5V*2A / 7h@5V*2A (wireless charging)
Life Time>5.5h (standard accessories)
Low Voltage Warning<3.65V
Antenna TypeDual antenna
DisplayHVGA 3.5 TFT, 320*480
LanguageChinese and English
SimulatorUSB Simulator
Data InterfaceUSB, Non-standard interface (USART), PHJACK (PPM)
Temperature Range-10℃—+60℃
Humidity Range20%-95%
Online UpdateYes
ColorBlack

3.2 FGr12B Receiver Specifications

FeatureDetail
Model TypeFGr12B
PWM Channels12
RF2.4GHz ISM
2.4GHz ProtocolAFHDS 3
Distance>500m (open without interference ground)
Antenna TypeSingle antenna
Power3.5V-9V
RSSIYes
Data Interfacei-BUS/S.BUS/PPM/PWM
Temperature Range-10℃-+60℃
Humidity Range20%-95%
Online UpdateYes
Size37mm*25mm*17.5mm
Weight11.2g
CertificationCE, FCC ID:N4ZFGR12B

4. Features

4.1 AFHDS 3 Protocol

AFHDS3 (third-generation automatic frequency hopping digital system) is a newly developed digital wireless system. It is compatible with single antenna bidirectional real-time data packet transmission and data stream transmission. With the advantages that come with the WS2A wireless system and the new 2.4GHz chip, the system can dynamically set: number of channels, channel resolution, range, anti-interference requirements and latency to meet the needs of different users.

4.2 Hardware Highlights

  • Rocker Type: 5D Hall waterproof rocker + 2 levers.
  • Third Rocker: One on the left and one longitudinal centering lever.
  • Other Controls: 6 gear switches (lengths may vary, accessories can be modified), 3 knob keys, 2 self-locking buttons, 8 fine-tuning buttons (two-way buttons).
  • Display Screen: 3.5-inch TFT color screen, HVGA 320*480 resolution, LCD white backlight, capacitive touch screen.
  • Vibration/Sound Alarm: Adjustable vibration intensity, different alarm sounds, and real voice prompts.
  • Charging: Supports Micro USB and QI wireless charging.
  • Battery: Built-in 4300mAh high-capacity lithium battery.
Detailed view of Flysky Paladin EV transmitter showing various controls and screen

Figure 4.1: Front view of the Paladin EV transmitter highlighting controls and display.

Side view of Flysky Paladin EV transmitter showing switches and ergonomic design

Figure 4.2: Side view of the Paladin EV transmitter.

Another side view of Flysky Paladin EV transmitter

Figure 4.3: Additional side view of the Paladin EV transmitter.

Back view of Flysky Paladin EV transmitter showing module bay and connectivity

Figure 4.4: Back view of the Paladin EV transmitter.

Top view of Flysky Paladin EV transmitter

Figure 4.5: Top view of the Paladin EV transmitter.

Front view of Flysky Paladin EV transmitter

Figure 4.6: Front view of the Paladin EV transmitter.

Flysky FGr12B receiver module

Figure 4.7: FGr12B Receiver module.

4.3 Software Highlights

  • Number of Channels: 18 ratio channels.
  • Dual Model Control: Supported.
  • Data Backup and Setting Sharing: Fusi remote control butler enables model data backup and sharing. The remote control can store 20 sets of models.
  • Upgrade: USB connection to a computer via the Fusi remote control butler for software network upgrades.
  • Additional Functions: Timer, Simulator.
  • Custom Function & Control: All channels can be customized, with custom allocation control and fine-tuning.
  • Unique Model Functions: Double ratio curve, delay function, 20 groups of customizable mixing control, track mixing control function.

5. Setup and Installation

5.1 Initial Charging

Before first use, fully charge the built-in 4300mAh lithium battery.

  • Micro USB Charging: Connect the provided Micro USB cable to the transmitter and a 5V/2A USB power adapter. Charging time is approximately 4 hours.
  • Wireless Charging (Ultimate Edition): Place the transmitter on the wireless charging dock. Charging time is approximately 7 hours.

5.2 Receiver Binding (FGr12B/FGr8B)

To establish communication between the transmitter and receiver, a binding process is required. Refer to the "Quick Operation Guide" included in your package for detailed, step-by-step binding instructions specific to your receiver model (FGr12B or FGr8B). Generally, this involves:

  1. Powering on the receiver while holding its bind button.
  2. Activating the binding function on the PL18 EV transmitter via its menu.
  3. Confirming successful binding through indicator lights on the receiver.

5.3 Connecting to a Model

Once bound, connect the receiver to your RC model (engineering vehicle, simulation ship, FPV racing drone) according to the model's specific wiring diagram and instructions. Ensure correct polarity and secure connections for all servos, ESCs, and other components. The receiver supports i-BUS/S.BUS/PPM/PWM data interfaces.

6. Operation

6.1 Basic Controls

  • 5D Hall Waterproof Rockers: Use for primary directional control (e.g., throttle, steering).
  • Levers: Additional proportional control inputs.
  • Gear Switches: Assignable for various functions like flight modes, gear retraction, or auxiliary controls.
  • Knob Keys: Proportional control for fine adjustments (e.g., camera tilt, gain settings).
  • Self-locking Buttons: For momentary or toggle functions.
  • Fine-tuning Buttons: Two-way buttons for precise adjustments of assigned channels.

6.2 Display and Menu Navigation

The 3.5-inch HVGA TFT capacitive touch screen allows for intuitive navigation through the transmitter's menus.

  • Touch Interface: Tap and swipe to access different settings and parameters.
  • Model Selection: Choose from up to 20 stored model configurations.
  • Channel Customization: Assign functions to various physical controls and fine-tune their response curves (double ratio curve, delay function).
  • Mixing Controls: Utilize the 20 groups of customizable mixing control and track mixing control functions for complex model setups.
  • System Settings: Adjust language (Chinese/English), alarm settings (vibration intensity, sound), and other system preferences.

6.3 Simulator Function

Connect the transmitter to a computer via USB to use it as a simulator controller. This allows for practice and familiarization with controls without risking your physical model.

7. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the transmitter and receiver. Avoid using solvents or abrasive cleaners.
  • Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures. Remove the battery if storing for extended periods (though it's built-in, ensure it's not fully discharged).
  • Battery Care: Avoid over-discharging or over-charging the built-in lithium battery. Charge regularly even if not in use to maintain battery health.
  • Firmware Updates: Regularly check for and install firmware updates via the Fusi remote control butler to ensure optimal performance and access to new features.
  • Physical Inspection: Periodically check all switches, rockers, and connections for any signs of wear or damage.

8. Troubleshooting

  • No Power: Ensure the battery is charged. If using wireless charging, verify proper placement on the dock.
  • Receiver Not Binding: Double-check the binding procedure in the Quick Operation Guide. Ensure the receiver is powered correctly and within range of the transmitter during binding.
  • Loss of Signal/Range Issues:
    • Ensure transmitter and receiver antennas are positioned correctly and not obstructed.
    • Check for local interference sources (e.g., Wi-Fi routers, other 2.4GHz devices).
    • Verify the receiver's power supply is stable (3.5V-9V).
  • Controls Unresponsive:
    • Confirm the receiver is bound and receiving signal (check receiver indicator lights).
    • Verify channel assignments and mixing settings in the transmitter's menu.
    • Inspect physical connections between the receiver and model components.
  • Display Issues: If the touch screen is unresponsive, try restarting the transmitter. Ensure the screen is clean and free from moisture.
  • Software Update Problems: Ensure a stable USB connection and internet access when using the Fusi remote control butler for updates.

For persistent issues, consult the detailed "Quick Operation Guide" or contact Flysky customer support.

9. Warranty and Support

The Flysky Paladin PL18 EV Radio Transmitter and its components are covered by a manufacturer's warranty against defects in materials and workmanship. Please retain your proof of purchase for warranty claims.

  • Online Support: Visit the official Flysky website for product information, FAQs, and firmware downloads.
  • Technical Assistance: For technical support or warranty service, please contact your retailer or the authorized Flysky service center in your region.
  • Certification: The FGr12B receiver holds CE and FCC ID: N4ZFGR12B certifications.

Note: The product might have some color difference due to different monitors and scenes. Please allow slight deviation for the measurement data.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.