Gledopto ST64 7W Pro LED Filament Light Bulb E27 User Manual

1. Product Overview

The Gledopto ST64 7W Pro LED Filament Light Bulb is a smart lighting solution featuring Zigbee 3.0 technology. It offers adjustable brightness and color temperature (warm white to cool white) and can be controlled via Zigbee gateways, 2.4G RF remote controls, or wall switches. Its vintage filament design makes it suitable for various decorative lighting applications.

2. Specifications

3. Setup

3.1 Important Voltage Information

The Gledopto Filament LED Bulb is suitable for an input voltage of AC220-240V. Please ensure that your country uses a voltage of AC220V-240V. It is not recommended for purchase or use in the United States and Mexico, as these regions typically use different voltage standards.

3.2 Installation

1. Turn off the power to the light fixture.
2. Carefully screw the bulb into the E27 socket.
3. Turn on the power. The bulb is now ready to be connected to a gateway or remote control.

3.3 Connecting with a Zigbee Hub/Gateway

These devices work with many Zigbee 3.0 Gateways like Philips Hue, Amazon Echo Plus, or SmartThings.

1. Start the device search function on your Zigbee 3.0 Gateway. This process may take some time.
2. If the Gateway does not find the device, try cycling the power to the bulb (turn off/on) or perform a reset (see section 5.1).
3. Once the device is found, the light will typically turn green. You can then save it to your desired rooms or groups within the gateway's application.
4. The device is now ready for use via your Zigbee hub.

3.4 Connecting with a 2.4G RF Remote Control (GL-RC-006Z)

The Gledopto Filament LED Bulb Pro can also work directly with a 2.4G RF Remote Control or Wall Switch without a Zigbee hub.

1. Within 3 seconds after the light is powered on, click the “on” button on the remote control for the desired group to perform code matching.
2. The LED light will turn green upon successful code matching.

4. Operating Instructions

4.1 Remote Control Functions (GL-RC-006Z)

The remote control allows you to manage up to six different zones of LED lights. Key functions include:

• Color Ring: Adjust the color of the light.
• CCT Slider: Adjust the color temperature (warm white to cool white).
• Brightness +/-: Increase or decrease the brightness.
• Master ON/OFF: Turn all linked lights ON or OFF.
• Zone ON/OFF: Turn lights in a specific zone ON or OFF.
• 6x(un)link light: Link or unlink lights to specific zones.
• 60s off delay: Activates a 60-second delay before turning off the lights.
• Speed +/-: Adjust the speed of dynamic modes.
• Modes (9 Programs): Cycle through various pre-programmed lighting modes.

4.2 Wall Switch Functions

Compatible multifunction wall switches offer similar controls to the remote, allowing direct control of the light without a gateway, including CCT, color, brightness, speed, and zone control.

4.3 App and Voice Control

Once connected to a compatible Zigbee gateway (e.g., SmartThings, Tuya), you can control the bulb via its dedicated mobile application on Android/iOS devices. This also enables voice control through platforms like Amazon Alexa, Google Home, and Apple HomeKit (via a compatible gateway).

Video demonstrating app control for adding lights, adjusting brightness, and color temperature.

4.4 Lighting Modes

The bulb supports various lighting modes, accessible via remote control or app:

1. Static Warm Light: Warm light only.
2. Static White Light: Cold light and warm light are equally bright.
3. Static Cold Light: Cold light only.
4. Static Red Light
5. Static Green Light
6. Static Blue Light
7. RGB Fade In/Fade Out: Colors fade in and out (red to green, green to blue, blue to red) with adjustable speed.
8. RGB Flash: Colors flash (red to green, green to blue, blue to red) with adjustable speed.
9. Color Breathing: Brightness of the current color cycles from 100% to 0% and back. You can switch colors during this cycle. Pressing the switch/mode button exits this mode.

5. Troubleshooting

5.1 Resetting the Bulb

If you encounter issues or need to re-pair the bulb, perform a reset:

1. Switch on your device (bulb).
2. Switch off the device within 2 seconds.
3. Wait for more than 5 seconds.
4. Repeat the off/on cycle five times.
5. The reset is complete when the device is switched on for the fifth time, and the LED light flashes 3 times.

5.2 Unlinking from Remote Control

1. If the LED is connected to a Zigbee hub, short press the “ON” key of the remote 5 times within 3 seconds after the light is powered on. The LED will blink 3 times under the existing color.
2. If the LED is NOT connected to a Zigbee hub, short press the “ON” key of the remote 5 times within 3 seconds after the light is powered on. The LED will blink 3 times until fully bright.

5.3 Power On Status Memory

The bulb can remember its last on/off status. To activate this function, cycle the power on and off 3 times. The light will flash 2 times, indicating the function is active. To cancel this function and revert to default (always on when powered), repeat the 3-cycle on/off operation.

6. Maintenance and Safety

6.1 General Attention

1. Always check that the input voltage of the constant voltage power supply is in accordance with the bulb's requirements (AC 220-240V) and ensure correct connection of both cathode and anode.
2. Use the product at its rated voltage. Over-voltage usage will cause damage.
3. Non-professional users should not dismantle the lamps directly, as this may cause fire or electric shock.
4. The working temperature range is -20°C to 45°C. Do not use the device in direct sunlight, moist environments, or other high-temperature areas.
5. Avoid using the lamps near metal areas and high magnetic fields, as this will negatively affect performance.

6.2 Battery Installation for Remote Control (GL-RC-006Z)

To install batteries in the remote control:

1. Carefully press the battery cover and push it downwards to open.
2. Install two AAA batteries, ensuring the negative (-) pole of each battery matches the largest spring.
3. Avoid touching the color ring during battery installation.
4. Replace the battery cover and ensure it is tightly secured.

7. Compatibility

7.1 Compatible Gateways

The Gledopto ST64 7W Pro LED Filament Light Bulb is compatible with many Zigbee 3.0 Gateways, including:

• Philips Hue
• Amazon Echo Plus
• SmartThings
• ConBee II
• Homey

7.2 Compatible Remote Controls

The bulb is compatible with Gledopto 2.4G RF Remote Controls, including models:

• GL-RC-006Z
• GL-RC-009
• GL-W-001Z (Wall Switch)

7.3 Compatibility Chart

Note: Compatibility with Homee is based on customer feedback and not officially verified by Gledopto.

8. User Tips

• Aesthetic Placement: The vintage look with transparent or brown glass and E27 socket blends well with modern and vintage decor styles, making it ideal for bedrooms, living rooms, cafes, and bars.
• Optimal Lighting: Use warm white (2200K) for relaxing environments like sleeping or resting, and cool white (6500K) for tasks requiring focus, such as working or reading.
• Energy Efficiency: This LED bulb offers lower power consumption, helping to save energy costs while providing versatile lighting.
• PDF Manual: For a detailed PDF version of the user manual, please refer to the official documentation.

9. Warranty and Support

This product comes with a 2-year warranty for indoor use.

For any questions, technical support, or more information, please contact Gledopto customer service online. We are committed to providing timely assistance.

Disclaimers

• This manual may contain inaccuracies or typographical errors. Gledopto reserves the right to update the contents of this manual based on product improvements and changes without prior notice.
• Product parameters may change due to continuous adoption of new technologies.
• This manual is for reference and guidance only; the actual product's application and configuration may vary.
• All texts, tables, and pictures in this manual are protected by national laws and may not be used without permission.