Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the XSDTS steel security door lock bodies, including models 6068, 7068, and 7568. These lock bodies are designed for use with both mechanical and fingerprint lock systems, offering robust security for various door types. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Specifications
| Attribute | Detail |
|---|---|
| Item Type | Lock Bracket |
| Material | 304 Stainless Steel |
| Application | Security door lock, Fingerprint lock |
| Model Numbers | 6068, 7068, 7568 |
| Origin | Mainland China |
| Package Contents | 1x Lock body, 1x Door frame guide piece (Lock cylinder sold separately) |
Dimensional Diagrams
Refer to the following diagrams for detailed dimensions of each lock body model. It is crucial to select the correct size based on your existing door lock body.

Figure 1: 7068 Lock Body (24*240) with detailed dimensions. Faceplate width 24mm, length 240mm. Backset 70mm, center distance 85mm (from 68mm and 17mm measurements).

Figure 2: 7568 Lock Body (24*240) with detailed dimensions. Faceplate width 24mm, length 240mm. Backset 75mm, center distance 85mm (from 68mm and 17mm measurements).

Figure 3: 6068 Lock Body (24*240, Width 75mm) with detailed dimensions. Faceplate width 24mm, length 240mm. Backset 60mm, center distance 68mm. The 'Width 75mm' refers to the body width.

Figure 4: 6068 Lock Body (30*388) with detailed dimensions. Faceplate width 30mm, length 388mm. Backset 60mm, center distance 68mm.

Figure 5: 6068 Lock Body (40*388) with detailed dimensions. Faceplate width 40mm, length 388mm. Backset 60mm, center distance 68mm.
Installation Guide
This section outlines the general steps for installing the lock body. Professional installation is recommended. Ensure you have the correct lock body model and size for your door.
- Preparation: Carefully remove your old door lock body. Compare its dimensions with the provided diagrams (Figures 1-5) to ensure compatibility with your new XSDTS lock body.
- Insert Lock Body: Slide the new lock body into the mortise pocket in the edge of the door. Ensure it fits snugly and aligns with the pre-drilled holes.
- Secure Lock Body: Fasten the lock body to the door using appropriate screws through the faceplate. Do not overtighten.
- Install Door Frame Guide: Attach the door frame guide piece (strike plate) to the door frame, ensuring it aligns perfectly with the lock's deadbolts and latch when the door is closed.
- Install Lock Cylinder/Panel: Install your chosen lock cylinder (mechanical or fingerprint) and the corresponding handle panel (if applicable) according to their specific instructions. Note that the lock cylinder is sold separately.
- Test Functionality: Before closing the door completely, test the lock's operation. Ensure the handle lifts and pushes down smoothly, and the deadbolts extend and retract correctly.
Adjustable Tongue Direction
The lock body features an adjustable tongue direction to accommodate different door orientations (left-hand or right-hand opening). To adjust:

Figure 6: Mechanism for adjusting the lock tongue direction. Locate the small pin or lever on the side of the latch bolt, push it, rotate the latch bolt 180 degrees, and release.
Locate the small pin or lever on the side of the latch bolt. Push it in, rotate the latch bolt 180 degrees, and then release the pin/lever to secure the latch in the new direction.
Operation
The basic operation of the lock body is as follows:
- To Lock: Lift the handle upwards. This action engages the deadbolts, securing the door.
- To Unlock: Push the handle downwards. This action retracts the deadbolts and latch, allowing the door to open.
Note on Multifunctional Panels: If you are using a multifunctional panel with your lock body, its operation may vary. Refer to the specific instructions provided with your multifunctional panel for detailed usage. Common configurations include:
- Configuration 1: Outside handle fixed, Inside handle pushes down to open.
- Configuration 2: Outside handle lifts up to lock (cannot push down), Inside handle lifts up to lock and pushes down to open.
- Configuration 3: Outside handle lifts up to lock and pushes down to open, Inside handle lifts up to lock and pushes down to open.
Maintenance
To ensure the longevity and smooth operation of your XSDTS lock body, follow these maintenance guidelines:
- Cleaning: Wipe the lock body and faceplate with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these can damage the stainless steel finish.
- Lubrication: Periodically apply a small amount of graphite-based lubricant or a silicone spray to the moving parts of the lock mechanism (latch bolt, deadbolts) to ensure smooth operation. Do not use oil-based lubricants, as they can attract dust and grime.
- Inspection: Regularly check all screws and fasteners to ensure they are tight. If any part appears loose or damaged, address it promptly.
- Environmental Factors: Protect the lock from excessive moisture or corrosive environments, which can accelerate wear and tear.
Troubleshooting
If you encounter issues with your lock body, consider the following common solutions:
- Stiff Operation: If the handle or bolts feel stiff, apply lubricant as described in the Maintenance section. Check for any obstructions in the door frame or mortise pocket.
- Bolts Not Engaging/Retracting Fully: Ensure the door frame guide piece (strike plate) is correctly aligned. Adjust if necessary. Check for any debris preventing full movement of the bolts.
- Loose Handles/Panels: Tighten any visible screws on the handle or panel assembly. If the issue persists, the problem might be with the external handle/panel unit, not the lock body itself.
- Lock Cylinder Issues: If the key or fingerprint reader is not working, the problem likely lies with the lock cylinder or fingerprint module, which is a separate component. Refer to its specific manual.
If these steps do not resolve the issue, contact a qualified locksmith or the XSDTS customer support for assistance.
User Tips
- Accurate Measurement is Key: Before purchasing and installing, always measure your existing lock body's dimensions (backset, center distance, faceplate width and length) precisely. This ensures a perfect fit and avoids compatibility issues.
- Consider Your Lock Type: This lock body is compatible with both mechanical and fingerprint lock systems. Ensure the external lock mechanism you pair it with is also compatible and provides the desired functionality.
Warranty and Support
For warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support or further assistance, please reach out to XSDTS customer service through your purchase platform or the official XSDTS website.