EPEVER Tracer5415AN, Tracer5420AN

Contents

EPEVER MPPT Solar Panel Charge Controller Tracer-AN Series (50-100A)

User Manual

Models: Tracer5415AN, Tracer5420AN

1. Product Overview

The EPEVER Tracer-AN series solar charge controller is an advanced Maximum Power Point Tracking (MPPT) device designed for off-grid solar systems. It features multi-phase synchronous rectification technology and a sophisticated MPPT algorithm to ensure high conversion efficiency and accurate tracking of the maximum power point of the PV array. This controller supports a three-stage charging mode, providing optimal battery charging and extending battery lifespan. It is suitable for various applications, including solar RVs, household systems, and field monitoring.

The Tracer-AN series offers robust communication capabilities via RS485, allowing for monitoring and control through PC software or mobile applications. It also includes comprehensive electronic protection functions to ensure system safety and reliability.

2. Safety Instructions

  • Always connect the battery first to the charge controller, then the solar panel, and finally the load. Disconnect in the reverse order.
  • Ensure all wiring is correctly polarized and securely connected to prevent damage to the controller or other components.
  • Install the controller in a well-ventilated area, away from flammable gases and liquids.
  • Do not disassemble or attempt to repair the controller yourself. Refer to qualified personnel for service.
  • Use appropriate circuit breakers and fuses for all connections to protect against overcurrent.
  • The temperature sensor (RTS) is crucial for accurate charging. If the temperature sensor is short-circuited or damaged, the controller will charge/discharge at a default temperature of 25℃.
  • Ensure proper grounding of the system as indicated in the wiring diagrams.

3. Product Features and Characteristics

The Tracer-AN series controllers are designed with a focus on efficiency, reliability, and user-friendliness. Key features include:

  • CE Certification: Complies with LVD EN/IEC62109-1, EMC EN61000-6-1/3 standards.
  • High Quality & Low Failure Rate: Components from ST and Infineon ensure product longevity.
  • Advanced MPPT Technology: Ultra-fast tracking speed with tracking efficiency up to 99.5%.
  • High Conversion Efficiency: Maximum DC/DC transfer efficiency up to 98%, full load efficiency up to 98%.
  • Accurate MPP Tracking: Advanced MPPT control algorithm minimizes power point loss rate and time, ensuring maximum power harvest.
  • Wide MPP Operating Voltage: Supports a broad range of PV input voltages.
  • Automatic Control: Limits charging power and current to prevent over-rated operation.
  • Flexible Battery Support: Compatible with Sealed, Gel, Flooded, and User-defined battery types.
  • Real-time Energy Record: Provides statistical function for energy monitoring.
  • Automatic Over-temperature Power Reduction: Protects the controller from overheating.
  • Full Load Operation: Achieves 100% full load operation in working environment temperature range during charging and discharging.
  • Parallel Support: Up to 6 units can be connected in parallel for system expansion.
  • Load Relay Control: External load switch signal to diversify load work modes.
  • Utility/Generator Relay: First and second disconnection of load control, contains two relays.
  • Remote Temperature Sensor: For accurate battery temperature compensation.
  • RS485 Port: 5VDC/200mA power output for communication modules.
  • Monitoring: Set parameters and monitor via mobile apps or PC software.
EPEVER Tracer AN Series Overview and Features

Figure 1: Overview and Key Features of Tracer AN Series

Controller Components

Labeled diagram of EPEVER MPPT Solar Charge Controller components

Figure 2: EPEVER Tracer AN Series Controller Components

  1. Charging LED indicator
  2. SELECT button
  3. Grounding Terminal
  4. Cover screw holes M4
  5. PV reverse polarity alarm indicator
  6. Generator and load relay enable
  7. RTS Port (Remote Temperature Sensor)
  8. RS485 port (5VDC/200mA)
  9. Utility/Generator relay ON
  10. RBVS Port
  11. Load control relay
  12. Utility/Generator relay OFF
  13. PV Terminals
  14. Battery Terminals
  15. LCD (Liquid Crystal Display)
  16. ENTER button
  17. Fault LED indicator

4. Installation and Wiring

Proper installation and wiring are critical for the safe and efficient operation of your solar charge controller. Please follow these steps carefully:

4.1 Mounting the Controller

  • Choose a dry, well-ventilated location, protected from direct sunlight, high temperatures, and water.
  • Mount the controller vertically on a wall or other sturdy surface to allow for proper heat dissipation.
  • Ensure there is sufficient clearance around the controller for air circulation.

4.2 Wiring Connections

Follow the wiring diagrams below for correct system connection. Always connect components in the specified order to prevent damage.

System connection diagram for EPEVER MPPT Solar Charge Controller with battery, solar, load, and optional utility/generator

Figure 3: Typical System Connection Diagram (with Utility/Generator)

System connection diagram for EPEVER MPPT Solar Charge Controller with battery, solar, and load, showing load relay

Figure 4: System Connection Diagram (with Load Relay)

Wiring diagram for parallel connection of multiple EPEVER MPPT Solar Charge Controllers

Figure 5: Parallel Connection Diagram for Multiple Controllers

  1. Connect the Battery: Connect the battery to the controller's battery terminals (marked with '+' and '-'). Ensure correct polarity.
  2. Connect the Solar Panel: Connect the solar panel array to the controller's PV terminals (marked with '+' and '-'). Ensure correct polarity.
  3. Connect the Load: Connect the DC load to the controller's load terminals (if applicable).
  4. Connect Optional Accessories: If using a Remote Temperature Sensor (RTS), plug it into the designated RTS port. Connect communication cables (RS485) for monitoring if desired.
  5. Grounding: Connect the grounding terminal of the controller to earth ground.

5. Operation

The EPEVER Tracer-AN series controller features an LCD display and two buttons (SELECT and ENTER) for easy navigation and parameter setting.

5.1 LCD Display and Buttons

  • LCD Display: Shows real-time system data, operating status, and fault information.
  • SELECT Button: Used to scroll through different display screens or menu options.
  • ENTER Button: Used to confirm selections, enter menus, or modify parameters.

5.2 Monitoring and Parameter Setting

The controller can be monitored and configured using dedicated software or mobile applications. Connect the controller via its RS485 port to a PC using a USB to RS485 cable (CC-USB-RS485-150U) or to a mobile device using a WiFi Serial Adapter (eBox-WIFI-01) or RS485 to Bluetooth Adapter (eBox-BLE-01).

  • PC Software: Provides detailed system data, historical records, and advanced parameter settings.
  • Mobile App: Offers convenient monitoring and basic parameter adjustments from your smartphone or tablet.

6. Technical Specifications

6.1 Electrical and Mechanical Parameters

Table of Electrical and Mechanical Parameters for EPEVER Tracer AN Series

Figure 6: Electrical and Mechanical Parameters

Electrical Parameters
ParameterValue
Ambient temperature range-25℃ ~ +60℃ (Derate above 45℃)
LCD temperature range-20℃ ~ +70℃
Storage temperature range-30℃ ~ +85℃
Relative humidity range5% to 95% (N.C.)
EnclosureIP20
Pollution degreePD2
Mechanical Parameters
ModelTracer5210/5415/5420ANTracer6210/6415/6420ANTracer8415/8420ANTracer10415/10420AN
Dimension261×216×119mm340×236×119mm394×240×134mm394×242×143mm
Mounting dimension180×204mm260×224mm300×228mm300×230mm
Mounting hole sizeΦ7
Terminal6AWG/16mm²6AWG/16mm²2AWG/35mm²2AWG/35mm²
Recommended cable6AWG/16mm²6AWG/16mm²4AWG/25mm²4AWG/25mm²
Weight3.5kg4.5kg6.1kg7.4kg

6.2 Detailed Technical Specifications

Table of Detailed Technical Specifications for EPEVER Tracer AN Series

Figure 7: Detailed Technical Specifications

Technical Specifications (Tracer5210AN - Tracer8415AN)
ModelTracer5210ANTracer6210ANTracer5415ANTracer6415ANTracer8415AN
Nominal System Voltage12/24VDC or Auto12/24/36/48VDC or Auto
Battery Input Voltage Range9V ~ 32V8V ~ 68V
Battery TypeLead-acid Battery (Sealed/Gel/Flooded/User), Lithium Battery (LiFePO₄/Li(NiCoMn)O₂/User)
Battery fuse150A/58V150A/58V
Rated charge current50A60A50A60A80A
Rated charge Power625W/12V, 1250W/24V750W/12V, 1500W/24V625W/12V, 1250W/24V, 1875W/36V, 2500W/48V750W/12V, 1500W/24V, 2250W/36V, 3000W/48V1000W/12V, 2000W/24V, 3000W/36V, 4000W/48V
Max. PV open circuit voltage150V150V
MPP Voltage Range(Battery Voltage +2V) ~ 72V(Battery Voltage +2V) ~ 108V
Tracking efficiency≥99.5%
Max. conversion efficiency98.0%98.0%98.3%98.6%98.5%
Full load efficiency97.0%97.0%97.8%
Temperature compensate coefficient-3mV/℃/2V (Default)
Self-consumption98mA/12V, 60mA/24V, 50mA/36V, 46mA/48V
GroundingCommon negative grounding
RelayRated Value: 5A/30VDC; Max
RS485 interfaceRated Value: 0.5A/5VDC, RS485 (RJ45)
LCD backlight timeDefault 60S, Range: 0~999S (0S: the backlight is ON all the time)
Technical Specifications (Tracer10415AN - Tracer10420AN)
ModelTracer10415ANTracer5420ANTracer6420ANTracer8420ANTracer10420AN
Nominal System Voltage12/24/36/48VDC or Auto
Battery Input Voltage Range8V ~ 68V
Battery TypeLead-acid Battery (Sealed/Gel/Flooded/User), Lithium Battery (LiFePO₄/Li(NiCoMn)O₂/User)
Battery fuse150A/58V
Rated charge current100A50A60A80A100A
Rated charge Power1250W/12V, 2500W/24V, 3750W/36V, 5000W/48V750W/12V, 1500W/24V, 2250W/36V, 3000W/48V750W/12V, 1500W/24V, 2250W/36V, 3000W/48V1000W/12V, 2000W/24V, 3000W/36V, 4000W/48V1250W/12V, 2500W/24V, 3750W/36V, 5000W/48V
Max. PV open circuit voltage150V
MPP Voltage Range(Battery Voltage +2V) ~ 144V
Tracking efficiency≥99.5%
Max. conversion efficiency98.6%98.3%98.1%98.5%98.6%
Full load efficiency97.1%97.5%97.5%97.5%97.6%
Temperature compensate coefficient-3mV/℃/2V (Default)
Self-consumption98mA/12V, 60mA/24V, 50mA/36V, 46mA/48V
GroundingCommon negative grounding
RelayRated Value: 5A/30VDC; Max
RS485 interfaceRated Value: 0.5A/5VDC, RS485 (RJ45)
LCD backlight timeDefault 60S, Range: 0~999S (0S: the backlight is ON all the time)

7. Optional Accessories

Enhance the functionality and monitoring capabilities of your Tracer-AN series controller with these optional accessories:

Table of Optional Accessories for EPEVER MPPT Solar Charge Controller

Figure 8: Optional Accessories

Optional Accessories
AccessoryDescription
Remote Temperature Sensor (RTS300R47K3.81A)Acquires battery temperature for accurate temperature compensation of control parameters. Standard cable length is 3m (customizable). Connects to the 4th port on the controller. NOTE: If the sensor is short-circuited or damaged, the controller will charge/discharge at a default temperature of 25℃.
USB to RS485 cable (CC-USB-RS485-150U)USB to RS485 converter for monitoring each controller using Solar Station PC software. Cable length is 1.5m. Connects to the RS485 Port on the controller.
Remote Meter MT50Displays various operating data and fault information. Features a backlit LCD screen and easy-to-operate buttons.
WIFI Serial Adapter (eBox-WIFI-01)Connects to the controller via standard Ethernet cable (parallel cable). Allows monitoring of operating status and parameters via mobile app through WiFi signals.
RS485 to Bluetooth Adapter (eBox-BLE-01)Connects to the controller via standard Ethernet cable (parallel cable). Allows monitoring of operating status and parameters via mobile app through Bluetooth signals.
Logger (eLOG01)Connects to the controller via RS485 communication cable. Records operating data and monitors real-time operating status via PC software.
PT Adapter (PT-ADP)Manages communication and synchronization for 2 to 8 controllers connected in parallel.

NOTE: For detailed setting and operation of accessories, please refer to the accessory's user manual.

8. Maintenance

Regular maintenance ensures the longevity and optimal performance of your EPEVER MPPT solar charge controller.

  • Cleanliness: Keep the controller clean and free from dust and debris. Use a dry cloth to wipe the exterior.
  • Connections: Periodically check all wiring connections for tightness and corrosion. Loose connections can cause overheating and damage.
  • Ventilation: Ensure that the ventilation openings are not blocked to allow for proper heat dissipation.
  • Battery Inspection: Regularly inspect your batteries for any signs of damage, corrosion, or leakage.
  • Firmware Updates: Check the manufacturer's website for any available firmware updates to ensure your controller has the latest features and bug fixes.

9. Troubleshooting

If you encounter issues with your EPEVER Tracer-AN series controller, consider the following basic troubleshooting steps:

  • No Display/Power: Check battery connections and ensure the battery voltage is within the controller's operating range. Verify that the battery fuse is intact.
  • No Charging: Ensure solar panel connections are correct and that there is sufficient sunlight. Check PV input voltage and current. Verify that the PV fuse is intact.
  • Load Not Working: Check load connections and ensure the load is not exceeding the controller's rated current. Verify load settings on the controller.
  • Error Codes: If the LCD displays an error code, refer to the full user manual (if available from the manufacturer) for specific meanings and solutions.
  • Communication Issues: Ensure communication cables are securely connected. Verify that the correct software/app is being used and that drivers are installed if connecting to a PC.

For more complex issues, it is recommended to consult the official EPEVER support resources or a qualified solar technician.

10. User Tips

Based on general user experiences with solar charge controllers:

  • Battery Type Setting: Always ensure the correct battery type is selected in the controller settings to prevent overcharging or undercharging, which can significantly impact battery life.
  • Cable Sizing: Use appropriately sized cables for all connections (PV, battery, load) to minimize voltage drop and maximize efficiency. Refer to the 'Recommended cable' specifications.
  • Monitoring: Utilize the monitoring capabilities (PC software or mobile app) to track system performance, identify potential issues early, and optimize settings.
  • Parallel Operation: If expanding your system with multiple controllers in parallel, ensure they are properly configured and synchronized using the PT Adapter for optimal performance.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or the official EPEVER customer service. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.