FlySky FS-i6

Contents

FlySky FS-i6 2.4G 6CH AFHDS Radio Controller Instruction Manual

Model: FS-i6 | Brand: FlySky

1. Introduction

This manual provides detailed instructions for the FlySky FS-i6 2.4G 6-channel AFHDS (Automatic Frequency Hopping Digital System) radio controller. Designed for fixed-wing aircraft, helicopters, and gliders, the FS-i6 offers reliable and interference-free control. It is compatible with a range of FlySky receivers, providing flexibility for various RC applications.

FlySky FS-i6 Transmitter with various compatible receivers
Overall view of the FlySky FS-i6 transmitter and compatible receivers.

2. Package Contents

The FS-i6 radio controller package typically includes the FS-i6 transmitter and a choice of receiver. Please verify your specific purchase for exact contents.

Package Included banner
Example of package contents banner.

Typical Configurations:

  • Only Mode 1 i6 Transmitter
  • Only Mode 2 i6 Transmitter
  • FS-i6 Transmitter with iA6 Receiver
  • FS-i6 Transmitter with iA6B Receiver
  • FS-i6 Transmitter with iA10B Receiver
  • FS-i6 Transmitter with X6B Receiver
  • FS-i6 Transmitter with A8S Receiver
  • FS-i6 Transmitter with RX2A Pro V1 Receiver
  • FS-i6 Transmitter with FS2A Receiver
  • FS-i6 Transmitter with Fli14+ Receiver

3. Specifications

3.1. FS-i6 Transmitter Specifications

FeatureSpecification
Channels6
Model TypeFixed wing / Helicopter / Glider
Channel Resolution1024 steps
Low Voltage WarningLess than 4.2V
Antenna Length26 x 2mm (dual antenna)
Weight392g
Battery6V (4 x 1.5AA, not included)
Size174 x 89 x 190 mm
ColorBlack
CertificateCE, FCC
RF Specification
RF Range2.405 - 2.475GHz
Bandwidth500kHz
RF PowerLess than 20dBm
RF ModeAFHDS 2A
Modulation TypeGFSK
RX Sensibility-105dBm

3.2. Receiver Specifications

FeatureFS-iA6BFS-iA6FS-iA10BFS-A8SFS-X6BFS-RX2A Pro V1Flysky FS2A 4CHFli14+
Channels6610PPM 8CH, i-BUS 18CH6(PWM), 8(PPM), 18(i-BUS)10(IBUS), 8(PPM)4CH14CH
Model TypeAirplane / Glider / HelicopterRC Airplane / Glider / HelicopterAirplane / Glider / HelicopterMulti-rotorMulti-RotorN/AN/AN/A
Frequency Range2.4055-2.475GHZ2.4-2.48 GHzN/A2.408-2.475GHz2.408-2.475 GHz2.408-2.475GHZ2.408-2.475GHZN/A
BandwidthN/AN/AN/A500KHz500KHzN/A135N/A
Number of Bands140140N/A135135135135N/A
Transmitting Power20dBmNot more than 20dBmN/AN/ANot more than 20 dBmN/AN/AN/A
RF Receiver Sensitivity-105dbm-105dBm-105dBm-92 dBm-95dBm-92dBm-92DBMN/A
2.4G ModeAFHDS 2AAFHDS 2AAFHDS 2AAFHDS 2AAFHDS 2AAFHDS 2AAFHDS 2AAFHDS 2A
EncodingGFSKGFSKN/AGFSKGFSKN/AN/AN/A
Antenna Length26mm * 2 (dual)N/A26mm * 2 (dual)26mm93mm (Dual)33mmN/A70mm (Dual)
Input Power4.0-6.5V DC4.0-6.5V DC4.0-6.5V DC4.0-8.4V4.0-8.4V5.0-20V3.3-10V4-6.5V DC
Dimensions47 x 26.2 x 15mm40.4 x 21.1 x 7.35 mm51mm*34mm*15mm20*14*5.3mm36*22*7.5mm12*15mm11 * 25MM25x15x5mm
Weight14.9g6.4g19.3g1.2g4.5g0.9g0.9 grams1.7g
i-Bus InterfaceYesNoYesYesYesYesN/AYes
Data Acquisition InterfaceYesNoYesN/AN/AN/AN/AN/A
Control DistanceN/AN/AN/A>300m>300m500m+400+ metersMore than 500m

4. Setup

4.1. Throttle Mode Selection

The FS-i6 transmitter supports two throttle modes:

  • Mode 1: Right Hand Throttle
  • Mode 2: Left Hand Throttle

Ensure you select the appropriate mode for your flying preference. The mode is typically set in the transmitter's system settings.

FlySky FS-i6 Transmitter in Mode 1 (Right Hand Throttle)
FS-i6 Transmitter in Mode 1.
FlySky FS-i6 Transmitter in Mode 2 (Left Hand Throttle)
FS-i6 Transmitter in Mode 2.

4.2. Binding Procedure (Coding Method)

To establish communication between your FS-i6 transmitter and a receiver, you must perform a binding procedure:

  1. Insert the code matching line (bind plug) of the receiver into the 'B' (Bind) port on the receiver.
  2. Power on the receiver. The blue light on the receiver should flash quickly, indicating it has entered binding mode.
  3. On the FS-i6 remote control, press and hold the 'Bind' button while powering on the transmitter. This will put the transmitter into code matching mode.
  4. Observe the receiver. If the blue light on the receiver flashes quickly and then turns off, the binding process was successful.
  5. Turn off the power to both the remote control and the receiver.
  6. Power them back on (transmitter first, then receiver) to enter normal operating mode. The blue light on the receiver should now be continuously on, indicating a successful bind.
  7. If the code matching is unsuccessful, repeat steps 1-4.
Receiver with 'B' port for binding
Example receiver showing the 'B' (Bind) port.

5. Operating Instructions

5.1. AFHDS 2A System Features

The FlySky FS-i6 utilizes the advanced AFHDS 2A (Automatic Frequency Hopping Digital System 2A) protocol, offering several key advantages:

  • Frequency Hopping: Operates in the 2.405 to 2.475GHz range, divided into 142 independent channels. Each radio system uses 16 different channels and 160 different hopping algorithms to ensure robust communication.
  • High Gain Antenna: The system employs a high-gain, multi-directional antenna covering the entire frequency band, paired with a high-sensitivity receiver for jamming-free, long-range transmission.
  • Unique ID Binding: Each transmitter has a unique ID. Once bound with a receiver, the receiver saves this ID and only accepts data from that specific transmitter, significantly increasing interference immunity and safety.
  • Low Power Consumption: Designed with low-power electronic components and a sensitive receiver chip. The RF modulation uses an intermittent signal to further reduce power consumption.
  • Automatic Identification: The AFHDS 2A system automatically switches between single-way and two-way communication modes based on operational needs.
  • Error Correction: Built-in multiple channel coding and error-correction mechanisms improve communication stability, reduce error rates, and extend reliable transmission distance.

5.2. Low Voltage Warning

The FS-i6 transmitter features a low voltage warning system. If the transmitter's battery voltage drops below 4.2V, an alert will be triggered, indicating that the batteries need to be replaced or recharged to ensure continued safe operation.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the transmitter and receivers. Avoid using solvents or abrasive cleaners.
  • Storage: Store the radio controller and receivers in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries from the transmitter if storing for extended periods.
  • Battery Care: Always use fresh or fully charged batteries. Do not mix old and new batteries, or different types of batteries. Dispose of used batteries responsibly.
  • Antenna Inspection: Regularly check the antennas on both the transmitter and receivers for any damage. Ensure they are securely attached.

7. Troubleshooting

  • No Power: Ensure batteries are correctly installed and fully charged. Check for any corrosion in the battery compartment.
  • No Signal/Loss of Control:
    • Verify that the transmitter and receiver are properly bound (refer to Section 4.2).
    • Check the distance between the transmitter and receiver; ensure it's within the specified range.
    • Inspect antennas for damage or obstruction.
    • Ensure no other 2.4GHz devices are causing interference in the immediate vicinity.
    • Check receiver power supply (4V-6.5V DC for most receivers).
  • Low Voltage Warning: Replace or recharge the transmitter's AA batteries immediately.
  • Unresponsive Controls: Check all connections between the receiver and your model's servos/ESCs. Ensure correct channel mapping in the transmitter settings.
  • Binding Failure: Repeat the binding procedure carefully (Section 4.2). Ensure the bind plug is correctly inserted and the receiver is powered on before the transmitter enters bind mode.

8. User Tips

  • Range Testing: Always perform a range test before flying a new model or after any significant changes to your setup to ensure reliable communication.
  • Fail-Safe Setup: Configure fail-safe settings on your receiver to ensure your model reacts predictably (e.g., throttle to idle, control surfaces neutral) in case of signal loss. Note that for FS-X6B, failsafe only works on PWM, not in PPM or IBUS.
  • Firmware Updates: Check the official FlySky website periodically for any available firmware updates for your FS-i6 transmitter or receivers, as these can improve performance and add features.
  • Battery Management: Use high-quality rechargeable AA batteries for the transmitter and always carry spares or ensure they are fully charged before use.

9. Compatibility

The FlySky FS-i6 transmitter is compatible with a wide range of FlySky receivers and other transmitters using the AFHDS or AFHDS 2A protocols. It supports 6CH PWM and 1 PPM signal output.

Compatible Transmitters (for listed receivers):

  • FS-GT2 / FS-GT2B / FS-GT2E / FS-GT2F / FS-GT2G
  • FS-GT3B / FS-GT3C / FS-IT4
  • FS-i4 / FS-T4B
  • FS-i6 / FS-i6S / FS-T6 / FS-CT6B
  • FS-i10 / FS-TH9X

Note: Some older receivers (first-generation AFHDS) may not support telemetry return functions.

10. Safety Information

Always operate your RC equipment responsibly and safely. Failure to do so can result in injury or property damage.

  • Pre-Flight Checks: Before each flight, perform thorough pre-flight checks, including battery levels, control surface movement, and signal integrity.
  • Operating Environment: Operate your RC model in open areas, away from people, animals, power lines, and other obstacles. Avoid flying in adverse weather conditions.
  • Battery Safety: Handle LiPo batteries with extreme care. Follow manufacturer guidelines for charging, discharging, and storage.
  • Children: Keep RC equipment out of reach of small children. Adult supervision is required for minors operating RC models.
  • Local Regulations: Be aware of and comply with all local laws and regulations regarding RC model operation.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.