EPever MSC-N Series

Contents

EPEVER MSC-N Series MPPT Solar Charge Controller User Manual

Models: MSC2210N, MSC3210N, MSC4210N, MSC4215N

Brand: EPever

1. Introduction

The EPEVER MSC-N series is a new generation of MPPT solar charge controllers designed with a unique two-way load output feature. These controllers efficiently manage power flow from solar panels to batteries and loads, ensuring optimal energy harvesting and system stability. The advanced Maximum Power Point Tracking (MPPT) technology allows the controller to quickly track the maximum power point of solar panels, increasing solar energy utilization by 20%-30% compared to traditional PWM methods.

The two-way load output voltage can be freely switched between 12V or 24V DC using an enable switch, catering to various load requirements. The controller also features adaptive three-stage charging, comprehensive electronic protections, and a high-efficiency buck-boost conversion circuit to prolong battery service life. MSC-N series controllers are ideal for security monitoring, RVs, and household solar systems.

Note: For MSC4210N and MSC4215N models, the rated battery voltage supports 24V only. For other MSC-N types, the rated battery voltage supports both 12V and 24V.

2. Safety Information

Please read all instructions and warnings in this manual carefully before installation and operation. Keep this manual for future reference.

  • Ensure all wiring is correctly polarized and securely connected to prevent damage to the controller or other components.
  • Do not disassemble or attempt to repair the controller yourself. Refer to qualified personnel for service.
  • Install the controller in a well-ventilated area, away from flammable materials and corrosive gases.
  • Ensure proper ventilation around the controller to prevent overheating.
  • Always disconnect the battery and solar panel power before installing or moving the controller.
  • Use appropriate circuit breakers or fuses for the battery, solar panel, and load circuits.
  • Wear appropriate personal protective equipment (PPE) when working with electrical systems.

3. Product Overview

3.1. Identification of Parts

Diagram showing the labeled parts of the EPEVER MSC-N MPPT Solar Charge Controller
Figure 1: EPEVER MSC-N Series Controller Parts Identification
  1. Power Indicator: Indicates the power status of the controller.
  2. Load 1 Indicator: Shows the status of Load 1.
  3. Load 2 Indicator: Shows the status of Load 2.
  4. Error codes: Displays system error codes.
  5. Load ON/OFF and setting button: Used to turn loads on/off and access settings.
  6. Load 1/Load 2/Prior Mode enable switch: Configures load output and priority mode.
  7. RS485 communication port: For connecting to external devices like remote meters or PC.
  8. Load 1 Terminals: Output terminals for Load 1.
  9. Load 2 Terminals: Output terminals for Load 2.
  10. Grounding terminal: For system grounding.
  11. RTS interface: Remote Temperature Sensor interface.
  12. PV Terminals: Input terminals for the PV array.
  13. Battery Terminals: Terminals for battery connection.
  14. Mounting Hole *4: Points for mounting the controller.
  15. Battery indicator: Displays battery charge status.
  16. PV Indicator: Displays PV array status.

Note: If the remote temperature sensor is not connected or damaged, the controller will charge or discharge the battery at the default temperature setting of 25 °C (no temperature compensation).

3.2. Naming Rules

Diagram explaining the naming convention for MSC-N series controllers
Figure 2: MSC-N Series Naming Rules

The model number provides information about the controller's specifications:

  • MSC: Denotes the MSC series.
  • First digit (e.g., 4): Maximum PV open circuit voltage (e.g., 4 = 100V).
  • Second digit (e.g., 2): Battery system voltage (e.g., 2 = 12V/24V).
  • Third and Fourth digits (e.g., 10): Battery charging current (e.g., 10 = 10A, 20 = 20A, 30 = 30A, 40 = 40A).
  • N: Indicates a common negative system.

4. Accessories

4.1. Included Accessories

The controller typically includes an external temperature sensor RT-MF58R47K3.81A for temperature compensation.

4.2. Optional Accessories

Table of optional accessories for EPEVER MSC-N controllers
Figure 3: Optional Accessories
NameInstruction
Remote Temperature Sensor RTS300R47K3.81AAcquires battery temperature for charging/discharging parameter compensation. Standard cable length is 3m (customizable). Connects to port ⑥. If not connected or damaged, controller charges/discharges at 25°C.
USB to RS485 cable CC-USB-RS485-150USpecial cable for connecting RJ45 port of the controller to a USB port of a PC. Length is 1.5m (customizable). Enables real-time monitoring and software updates via Solar Station Monitor software.
Remote Meter MT92Displays operating status and faults via an LCD screen, allows browsing interface, and configuring parameters using buttons.
WiFi module eBox-WIFI-01After connecting to the controller via a standard Ethernet cable, operating status and parameters can be monitored by mobile APP via WiFi signal.
Bluetooth module eBox-BLE-01After connecting to the controller via a standard Ethernet cable, operating status and parameters can be monitored by mobile APP via Bluetooth signal.

5. Installation

5.1. Mounting

Mount the controller vertically on a flat, non-flammable surface in a well-ventilated indoor environment. Ensure there is sufficient clearance around the controller for heat dissipation. Avoid direct sunlight, high temperatures, and humid environments.

5.2. Wiring Connection

Follow the connection order strictly to prevent damage. Always connect the battery first, then the PV array, and finally the load.

5.2.1. Battery Mode Connection

Connection diagram for battery mode, showing PV array, controller, battery, and loads
Figure 4: Battery Mode Connection Diagram
  1. Connect the battery to the controller's BAT terminals (13). Ensure correct polarity (+ to + and - to -).
  2. Connect the PV array to the controller's PV terminals (12). Ensure correct polarity.
  3. Connect Load 1 to the Load 1 Terminals (8) and Load 2 to the Load 2 Terminals (9).

5.2.2. No-Battery Mode Connection

Connection diagram for no-battery mode, showing PV array directly powering loads
Figure 5: No-Battery Mode Connection Diagram

In no-battery mode, the PV array directly powers the load. This mode is activated by setting the rated voltage level of the battery to auto-recognition mode via PC software or a remote meter (refer to MT92 user manual for details).

CAUTION:

  1. Only when the power of the PV array is greater than the total power of the load and the load power does not change drastically, will the load work normally.
  2. In the condition of two-way load, when the power of the PV array is lower than the total power of the loads, but can meet the power of load 2, the output of load 2 is given priority. Load 1 will be turned off and restarted every 30 minutes until it can work normally.

6. Operation

6.1. Basic Operation

Once connected, the controller will automatically begin charging the battery from the PV array. The indicators on the front panel will show the charging status, battery level, and load status.

  • Charging: The PV indicator (16) and Battery indicator (15) will show activity during charging.
  • Load Output: Use the Load ON/OFF and setting button (5) to control the load output. The Load 1 (2) and Load 2 (3) indicators will show their respective statuses.

6.2. Load Output Control

The MSC-N series features a two-way load output. The output voltage can be set to 12V or 24V DC using the Load 1/Load 2/Prior Mode enable switch (6). The controller can also cut off load output in stages based on battery voltage to protect the battery and ensure critical load (Load 1) operation.

6.3. Monitoring

The controller's operation can be monitored and configured through several methods:

  • Remote Meter MT92: Connect the optional MT92 remote meter to view real-time data and adjust parameters.
  • Bluetooth/WiFi Module: Use an eBox-BLE-01 (Bluetooth) or eBox-WIFI-01 (WiFi) module connected via Ethernet cable to monitor and control the controller via a mobile application.
  • PC Software: Connect the controller to a PC using the CC-USB-RS485-150U cable and use the Solar Station Monitor software for detailed monitoring and configuration.

7. Maintenance

Regular maintenance ensures optimal performance and longevity of your solar charge controller.

  • Check Connections: Periodically inspect all wiring connections for tightness and corrosion. Loose connections can cause overheating and power loss.
  • Cleanliness: Keep the controller clean and free from dust and debris. Use a dry cloth to wipe the exterior.
  • Ventilation: Ensure that the ventilation openings are not blocked. Adequate airflow is crucial for heat dissipation.
  • Battery Inspection: Regularly check the battery terminals for corrosion and ensure the battery is in good condition.
  • Firmware Updates: Check the manufacturer's website for any available firmware updates to ensure your controller has the latest features and bug fixes.

8. Troubleshooting

If you encounter issues with your EPEVER MSC-N series controller, refer to the following common problems and solutions:

ProblemPossible CauseSolution
No charging indicationPV array not connected, insufficient sunlight, reversed PV polarity, or PV open circuit.Check PV connections, ensure adequate sunlight, verify PV polarity, and check for open circuits.
Load not workingLoad output disabled, battery low voltage disconnect, load short circuit, or load open circuit.Enable load output, check battery voltage, inspect load wiring for shorts or open circuits.
Controller displays error codeVarious system faults (e.g., over-voltage, over-current, high temperature).Refer to the detailed error code list in the full user manual for specific actions. Address the underlying cause (e.g., reduce PV input, improve ventilation).
Inaccurate temperature compensationRemote temperature sensor not connected or faulty.Ensure the remote temperature sensor is correctly connected to the RTS interface (11). Replace if faulty.

9. Specifications

FeatureDescription
Brand NameEPever
Model NumberMSC-N Series (MSC2210N, MSC3210N, MSC4210N, MSC4215N)
ApplicationSolar System Controller
Is Smart DeviceYes
CertificationCE
OriginMainland China
MPPT Tracking EfficiencyUp to 99.5%
DC/DC Transfer EfficiencyUp to 98.6% (Max), 96.6% (Full Load)
Conversion EfficiencyUp to 98.9% (Buck-boost chip)
Battery System Voltage12V/24V Auto (24V only for MSC4210N/MSC4215N)
Battery Types SupportedLead-acid and Lithium batteries (programmable)
Load OutputTwo-way, 12V/24V DC switchable
Dimensions (Approx.)Length: 40cm, Width: 20cm, Height: 10cm
Weight (Approx.)2.2 kg

10. User Tips

  • For optimal performance, ensure your PV array voltage is significantly higher than your battery voltage, especially for 12V systems, to fully utilize the MPPT capabilities.
  • When using the two-way load output, consider prioritizing essential loads on Load 1, as it may receive power even when Load 2 is temporarily cut off due to low PV power.
  • Regularly check the controller's status via a remote meter or app to monitor system health and adjust settings as needed.
  • If experiencing intermittent load operation in no-battery mode, verify that the PV array power consistently exceeds the total load power.

11. Warranty and Support

EPEVER products are designed for reliability and performance. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official EPEVER website. In case of technical issues or support inquiries, please contact your authorized dealer or EPEVER customer service. Ensure you have your product model number and purchase details ready when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.