1. Introduction
This manual provides instructions for the A-OK AC125-01 and AC126-01 RF433 Wireless Wall Switches. These switches are designed to wirelessly control A-OK RF433 compatible curtain motors and tubular motors. The AC125-01 is a single-channel switch for one motor, while the AC126-01 is a dual-channel switch capable of controlling two motors separately.
2. Product Overview
The A-OK wireless wall switches offer a modern and convenient way to control your motorized curtains or blinds without complex wiring. They feature a sleek design with a scratch-resistant acrylic panel and moisture-proof treatment, ensuring durability and aesthetic appeal.
2.1 Models
- AC125-01: Single Controller Sticker Switch. Designed to control one RF433 motor.
- AC126-01: Dual Controller Sticker Switch. Designed to control two RF433 motors separately.
3. Specifications
| Feature | Specification |
|---|---|
| Model Numbers | A-OK AC125-01 / AC126-01 |
| Frequency | RF433.92MHz |
| Battery Type | 27A 12V (not included) |
| Working Temperature | -20°C to +55°C |
| Transmitting Power | ≤10mW |
| Dimensions (L x W x H) | 86mm x 86mm x 10.5mm |
| Installation Hole Spacing | 60mm |
| Certification | CE |
| Origin | Mainland China |
| Compatibility | A-OK RF433 curtain/tubular motors |
4. Setup
4.1 Battery Installation
- Gently pry open the front panel of the switch to reveal the battery compartment.
- Insert one 27A 12V battery into the designated slot, ensuring correct polarity (+/-). Note: Battery is not included in the package.
- Snap the front panel back into place.
4.2 Mounting the Switch
The switch can be easily fixed to a wall using the pre-applied 3M double-sided adhesive or by screwing it into place using the installation positioning holes.
- Adhesive Mounting: Peel off the protective film from the 3M adhesive pads on the back of the switch. Press firmly onto a clean, dry, flat wall surface.
- Screw Mounting: Use appropriate screws (not included) through the designated installation positioning holes (60mm apart) to secure the switch to the wall.
4.3 Pairing with A-OK RF433 Motor
To control your curtain or tubular motor, the wall switch must be paired with the motor. The specific pairing procedure is typically detailed in the instruction manual provided with your A-OK RF433 motor. Please refer to your motor's manual for precise pairing steps. Generally, this involves putting the motor into a pairing mode and then pressing a button on the wall switch.
5. Operation
Once paired, the wall switch provides intuitive control over your motorized curtains or blinds.
5.1 Button Functions (AC125-01 Single Controller)
- Up Arrow Button: Press to open the curtain/blind.
- Middle Bar Button: Press to pause the curtain/blind movement.
- Down Arrow Button: Press to close the curtain/blind.
5.2 Button Functions (AC126-01 Dual Controller)
The AC126-01 features two sets of control buttons, allowing independent control of two separate motors.
- Each column of buttons (Up Arrow, Middle Bar, Down Arrow) controls one motor.
- Use the left column for Motor 1 and the right column for Motor 2 (after successful pairing).
5.3 Demonstration Video
6. Maintenance
6.1 Battery Replacement
When the switch's indicator light no longer illuminates or the motor response becomes inconsistent, it may be time to replace the battery. Follow the battery installation steps (Section 4.1) to replace the 27A 12V battery.
6.2 Cleaning
To clean the switch, gently wipe the acrylic panel with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the surface.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Switch not responding / Indicator light off | Dead or incorrectly installed battery. | Check battery polarity and replace with a new 27A 12V battery if necessary. |
| Switch not controlling motor | Switch not paired with the motor, or pairing lost. | Refer to your A-OK RF433 motor's instruction manual to re-pair the switch with the motor. |
| Motor responds intermittently | Low battery or interference. | Replace battery. Ensure no strong RF interference sources are nearby. |
8. User Tips
- Always ensure the correct battery type (27A 12V) is used for optimal performance.
- Keep the switch within the recommended operating range of your A-OK RF433 motor for reliable control.
- If you encounter issues with programming or pairing, consult the specific manual for your A-OK RF433 motor, as the pairing process can vary slightly between motor models.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your original retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
