HobbyEagle A3 Pro V2

Contents

HobbyEagle A3 Pro V2 6-Axis Gyro & Stabilizer User Manual

For R/C Airplanes Fixed-wing

Introduction

Thank you for purchasing the HobbyEagle A3 Pro V2. This is a high-performance and functional 6-axis gyro and stabilizer designed for R/C airplanes. To ensure safe operation and optimal performance, please read this instruction manual carefully and set up the device as described below.

The A3 Pro V2 features a 32-bit MCU and a high-precision 6-axis MEMS sensor, offering improved hardware and firmware for reliable performance. It supports various receiver types including standard PWM, PPM, and multi-protocol digital serial receivers, simplifying connection to your receiver.

Important Notes & Safety

  • Radio controlled (R/C) models are not toys! Propellers rotate at high speed and pose potential risk. They may cause severe injury due to improper usage. Always observe common safety rules for R/C models and local laws.
  • Read these instructions thoroughly before first use and set up the gyro carefully. We recommend seeking assistance from an experienced pilot before your first flight.
  • After power on, the A3 Pro V2 performs an accurate gyroscope calibration. Keep the airplane stationary while the LED flashes blue. The LED will stay solid blue if movement is detected, and calibration will not start until the airplane is still. Leveling the airplane is NOT required during initialization.
  • A stick centering is also required after gyroscope calibration. Always place all sticks at the center (throttle stick in the lowest position) before powering on, and do not move them until initialization is complete.
  • Always check the gyro direction for Aileron, Elevator, and Rudder channels after installation and perform a test before each flight. Incorrect gyro reaction can lead to loss of control or a crash.
  • It is recommended to use the supplied 3300uF/16V capacitor for a more stable and secure working voltage. The capacitor can be plugged into any free connector on the gyro or receiver.

Setup

Mounting Orientation

Use one of the supplied double-sided tapes to firmly attach the gyro to your airplane. For best performance, mount the gyro as close to the Center of Gravity (C.G.) as possible. The housing edges must be aligned exactly parallel to all three rotation axes of the plane. The gyro can be attached flat or upright, and even upside down. Ensure the arrow on the sticker always points to the heading direction; otherwise, the gyro will not function correctly in ANGLE, LEVEL, and HOVER modes.

Important: Never use hot-melt glue or nylon ties to fix the gyro. Only one piece of tape is needed. Soft or thick mounting may impact performance. Keep the gyro away from other electronic devices or wires.

HobbyEagle A3 Pro V2 mounted flat, face up
Flat, face up
HobbyEagle A3 Pro V2 mounted flat, face down
Flat, face down
HobbyEagle A3 Pro V2 mounted upright, button up
Upright, button up
HobbyEagle A3 Pro V2 mounted upright inverted, button down
Upright Inverted, button down

Receiver Connection

Pay attention to the polarity of the plugs. The orange signal line must always be on the top and the brown on the bottom.

Standard PWM Receiver Connection

Connect the gyro to your standard PWM receiver as shown in the diagram below. The [MODE] port is used for flight mode switching via a 3-way switch channel on your receiver. The [Serial RX/G] port is for remote master gain adjustment using a proportional channel (volume or slide lever) on your transmitter. The ESC or throttle servo connects directly to the receiver's throttle channel, bypassing the gyro.

Wiring diagram for HobbyEagle A3 Pro V2 with a standard PWM receiver, ESC, and servos
Standard PWM Receiver Connection Diagram. Shows connections for Rudder, Elevator, Aileron servos, ESC, and receiver.

Single-Line Receiver Connection

The A3 Pro V2 supports PPM and multi-protocol digital serial receivers, allowing a single-wire connection to the receiver. The appropriate receiver channel allocation will be preset. If your radio's channels are not in the correct order, adjust the channel mapping in the Receiver Menu. In single-line receiver mode, the [THR Out/AIL] port can serve as the throttle output for the ESC or throttle servo if a mini receiver with no additional output connectors is used.

Note: The remote master gain channel is disabled by default in single-line mode. Assign a channel number in the Receiver Menu to activate this feature if needed.

Wiring diagram for HobbyEagle A3 Pro V2 with a single-line serial receiver, ESC, and servos
Single-Line Receiver Connection Diagram. Shows connections for Rudder, Elevator, Aileron servos, ESC, and a serial receiver.

Spektrum Satellite Receiver Connection

If using a Spektrum DSM2/X satellite with the A3 Pro V2, a DSM Adapter [HEDSMADP] is required to connect the satellite to the gyro.

Wiring diagram for HobbyEagle A3 Pro V2 with a Spektrum DSM2/X satellite receiver via a DSM adapter
Spektrum Satellite Receiver Connection Diagram. Shows connections for Rudder, Elevator, Aileron servos, ESC, and a Spektrum DSM2/X satellite receiver via a DSM Adapter.

Operating Instructions

Flight Modes

The A3 Pro V2 offers 6 flight modes, switchable via a 3-position switch on your transmitter. The factory default allocation is OFF - NORMAL - LEVEL. The LED color indicates the current flight mode.

LED Color Flight Mode
Solid RedGYRO OFF Mode
Solid BlueNORMAL Mode
Blue, FlashingLOCK Mode
Solid VioletANGLE Mode
Violet, FlashingLEVEL Mode
Violet, Fast FlashingHOVER Mode

1. GYRO OFF Mode

In GYRO OFF mode, the gyro is completely deactivated, and the airplane is controlled solely by your transmitter. This mode is primarily for testing.

2. NORMAL Mode (Rate Mode)

This is the basic function, correcting only momentary rotational movements. Servos return to neutral after rotation stops. It improves stability, precision, and reduces stall points.

3. LOCK Mode (Attitude Lock / 3D / AVCS Mode)

The gyro performs continuous correction for rotational movements. When sticks are released, the airplane holds its current position. Ideal for 3D maneuvers like hovering or knife edge, and helpful for landing.

4. ANGLE Mode (Trainer / Attitude Mode)

Limits the maximum roll and pitch angles, preventing rolls and loops. The airplane is stabilized regardless of stick input and returns to horizontal when sticks are released. Useful for emergency rescue or beginner training. Maximum angle can be set in the Setup Menu.

5. LEVEL Mode (Auto-Level / Auto-Balance / Horizon Mode)

Automatically brings the airplane to a horizontal position when sticks are released. Unlike ANGLE mode, there's no maximum angle limitation. Stabilization occurs only when there's no specific control input from aileron and elevator sticks. Useful for disorientation recovery.

6. HOVER Mode (Auto-Hover Mode)

Similar to LEVEL mode, but brings the airplane to a vertical (nose up) position for hovering when sticks are released. Designed to assist with learning hovering maneuvers.

Gain Adjustment

Basic Gain

Three trimming potentiometers on the front of the A3 Pro V2 adjust basic gain for Aileron, Elevator, and Rudder independently. Clockwise increases gain, anticlockwise decreases. Basic gain determines the momentary reaction strength. Higher gain leads to better stability and precision but can cause oscillation if too high. Too low gain results in weak control and overshooting. Turning gain to 0% deactivates the gyro.

For the first flight, start with a lower basic gain (e.g., 30%) in NORMAL mode. Reduce gain if oscillation occurs; increase if control feels weak or imprecise.

Remote Master Gain

The [Serial RX/G] port controls master gain remotely. Use a volume or slide lever on your transmitter for linear adjustment, or a 3-position switch for 3-level gain selection. This function is optional; if not connected, master gain defaults to 100%.

Setting Methods

The gyro has two menus for setup: the Setup Menu and the Receiver Menu.

Setup Menu

Menu Accessing: While the gyro is working, press and hold the button for 2 seconds. Release when the LED flashes White quickly.

Diagram showing how to access the Setup Menu by pressing and holding the button until the LED flashes white
Setup Menu Access: Press and hold the button for ~2 seconds until the LED flashes White quickly.

Function Selection: In the Setup Menu, the LED flashes White multiple times every 3 seconds in a loop. The number of flashes indicates the current function item (e.g., one flash for "Wing Type", two for "Mount Orientation").

Option Switching: Short press the button to enter a function. The LED color shows the currently selected option. Each short press advances to the next option. After selection, wait 5 seconds for the LED to blink quickly, indicating the change is saved. You will then return to the Setup Menu. To skip changes, wait for timeout.

Exit of Menu: Press and hold the button for 2 seconds until the LED flashes White quickly.

Receiver Menu

Menu Accessing: Turn on the gyro while holding down the button. Release when the LED lights solid Violet.

Diagram showing how to access the Receiver Menu by holding the button during power-on until the LED lights solid violet
Receiver Menu Access: Hold the button while powering on until the LED lights solid Violet.

Function Selection: In the Receiver Menu, the LED flashes Violet multiple times every 3 seconds in a loop. The number of flashes indicates the current function item (e.g., one flash for "Receiver Type", two for "Aileron channel").

Option Switching: Short press the button to enter a function. The LED color shows the currently selected option. Each short press advances to the next option. After selection, wait 5 seconds for the LED to blink quickly, indicating the change is saved. You will then return to the Receiver Menu. To skip changes, wait for timeout.

Exit of Menu: Press and hold the button for 2 seconds until the LED flashes Violet quickly. New receiver settings take effect immediately after exiting without restarting the gyro.

Gyro Direction Check

VERY IMPORTANT! Ensure the gyro reacts in the correct direction for each channel before flight. An opposite reaction could lead to loss of control or a crash!

Check Aileron Gyro Direction

Quickly move the right wing downward around the roll axis. The right aileron surface should flap down and the left flap up. This corrects for the roll motion.

Check Elevator Gyro Direction

Quickly move the nose of the airplane downward around the pitch axis. The elevator surface should flap up. This corrects for the pitch motion.

Check Rudder Gyro Direction

Quickly move the nose of the airplane to the left around the yaw axis. The rudder surface should flap right. This corrects for the yaw motion.

Calibration

Level Calibration

Required for ANGLE and LEVEL modes. This calibrates the gyro's understanding of the airplane's roll and pitch angles. Place the airplane on a horizontal surface with wings parallel to the ground and slightly nose-up. Short press the button when the LED flashes 5 times in the Setup Menu. The LED will blink Blue rapidly; do not move the airplane until calibration is complete.

Hover Calibration

Recommended for HOVER mode. Lift the airplane and hold it vertical to the ground. Short press the button when the LED flashes 6 times in the Setup Menu. The LED will blink Blue rapidly; do not move the airplane until calibration is complete.

Accelerometer Calibration

While units are factory calibrated, re-calibration may be needed due to temperature changes or sensor replacement. Perform on a horizontal desktop with the gyro removed from the airplane.

Entering Calibration: Press and hold the button while powering on the gyro. Release when the LED starts flashing Violet slowly (do not release if it turns solid Violet, as this enters the Receiver Menu).

Calibration Steps:

  1. Step 1 (Face Up): Place the gyro flat, face up, parallel to the desktop. Short press the button. Do not move the gyro while the LED flashes Blue quickly.
  2. Step 2 (Face Down): Place the gyro flat, face down, parallel to the desktop. Short press the button. Do not move the gyro while the LED flashes Blue quickly.

Finish: After both steps, the LED flashes Violet once, indicating successful calibration. The gyro will then initialize automatically.

Advanced Settings (Setup Menu)

These settings are accessed via the Setup Menu (see "Setting Methods" above).

Wing Type

Supports standard fixed-wing, delta-wing (flying-wing), and V-tail. Default is Standard (Red LED). Short press the button to cycle through types. Wait 5 seconds to save.

LED Color Description
Solid RedStandard (default)
Solid GreenFlying-wing (Delta-wing)
Solid BlueV-Tail

Note: Ensure no mixing functions are active on your transmitter. If using two aileron servos, connect a Y-extended lead to [OUT1]. For flying-wings without a rudder, [RUD] connection is unnecessary.

Maximum Angle (for ANGLE mode)

Sets the maximum allowed tilt angle. Default is ±60° (Green LED). Short press to cycle through values. Wait 5 seconds to save.

LED Color Angle
Solid Red±30°
Solid Green±60° (default)
Solid Blue±90°
Solid YellowRoll ±120° / Pitch ±90°
Solid WhiteRoll ±150° / Pitch ±90°
Solid VioletRoll ±180° / Pitch ±90°

Servo Frequency

Sets the working frequency of the servos. Analog servos only work at 50Hz. Higher frequencies improve flight performance but ensure your servos can tolerate them to avoid damage. Default is 50Hz (Red LED). Short press to cycle through values. Wait 5 seconds to save.

LED Color Frequency
Solid Red50Hz (default)
Solid Green65Hz
Solid Blue165Hz
Solid Yellow200Hz
Solid White270Hz
Solid Violet333Hz

Gain Level

Adjusts the basic gain level. Default is Medium (Green LED). Short press to cycle between Small, Medium, and Large. Wait 5 seconds to save.

LED Color Gain Level
Solid RedSmall
Solid GreenMedium (default)
Solid BlueLarge

Factory Reset

Resets the gyro to factory settings. In the Setup Menu, when the LED flashes Blue, press and hold the button for 2 seconds until the LED flashes Blue quickly. Release to confirm the reset.

Firmware Version Display

To check the firmware version: Press and hold the button while powering on the gyro for more than 10 seconds. Release when the LED flashes Violet quickly. The number of Blue flashes indicates the major version, and Red flashes indicate the minor version (e.g., two Blue flashes followed by one Red flash means V2.1).

Maintenance

  • Keep the gyro clean and free from dust and moisture.
  • Avoid extreme temperatures and direct sunlight.
  • Regularly check all connections for secure fit and signs of wear.
  • Ensure the mounting tape is still firmly attached to prevent vibration-induced issues.
  • Firmware is upgradable (an optional data cable is required). Check the HobbyEagle website for updates.

Troubleshooting

  • Gyro not initializing: Ensure the airplane is stationary after power-on. Check that all sticks are centered (throttle at lowest) before powering on.
  • Airplane oscillates in flight: The basic gain for the corresponding axis might be too high. Reduce the gain gradually.
  • Weak or imprecise control: The basic gain for the corresponding axis might be too low. Increase the gain gradually.
  • Gyro not responding correctly: Verify the gyro direction for Aileron, Elevator, and Rudder channels as described in the "Gyro Direction Check" section. Incorrect direction can lead to crashes.
  • Unexpected behavior in ANGLE/LEVEL mode: Perform a Level Calibration to correct for installation angle deviations.
  • Issues with serial receiver connection: Check channel mapping in the Receiver Menu. Ensure correct polarity of plugs (orange signal line on top, brown on bottom).
  • No remote master gain control: Ensure the [Serial RX/G] port is connected to a proportional channel and a channel number is assigned in the Receiver Menu.

User Tips

  • Compatibility Check: The A3 Pro V2 is compatible with most standard PWM receivers, PPM, and multi-protocol digital serial receivers (including Futaba S.Bus, Spektrum DSM/DSMX, Multiplex SRXL/JR XBUS, Graupner SUMD, FlySky iBus, JETI EXBus, TBS/ELRS CRSF). Always verify your radio's protocol and channel order.
  • Capacitor for Stability: Utilize the included 3300uF/16V capacitor by plugging it into any free port on the gyro or receiver to ensure a stable power supply, especially with high-draw servos.
  • Initial Setup Patience: Take your time during the initial setup and calibration steps. Accurate mounting and calibration are crucial for optimal flight performance and safety.

Specifications

Feature Detail
Main Controller32-bit MCU
SensorsHigh-precision MEMS 6-axis sensor (3-axis gyroscope, 3-axis accelerometer)
Gyroscope Scale Range±2000 dps
Accelerometer Scale Range±4g
PWM Output920uS to 2120uS (1520uS center), 50Hz to 333Hz
Input Voltage4.8V to 8.4V
Operating Temperature-10 ℃ to 50 ℃
Size43 x 27 x 14 mm
Weight10g (excluding wires)

Serial Receiver Protocols Supported:

  • PPM Receiver
  • Futaba S.Bus (compatible with FrSky SBUS, RadioLink SBUS and WFLY WBUS)
  • Spektrum DSM/DSMX 1024 Satellite Receiver
  • Spektrum DSM/DSMX 2048 Satellite Receiver
  • Spektrum SRXL
  • Multiplex SRXL / JR XBUS Mode B
  • Graupner SUMD
  • FlySky iBus
  • JETI EXBus
  • TBS/ELRS CRSF

Package Contents

The package typically includes:

  • 1 x A3 Pro V2 Main Controller
  • 4 x Receiver Cables
  • 1 x Adapter (for Spektrum Satellite, if included)
  • 2 x Double-sided Tapes
  • 1 x 3300uF/16V Capacitor
Image showing the contents of the HobbyEagle A3 Pro V2 package: main controller, cables, adapter, and double-sided tapes
Typical package contents for the A3 Pro V2.
Image showing the HobbyEagle A3 Pro V2 controller with included accessories like cables, capacitor, and mounting tape
A3 Pro V2 controller and accessories.

Unboxing Video:

Video demonstrating the unboxing and contents of the HobbyEagle A3 Pro V2 package.

Warranty and Support

For warranty information, technical support, and further assistance, please refer to the official HobbyEagle website or contact your retailer. Always ensure you are using the latest firmware available for optimal performance and compatibility.

A detailed user manual in PDF format is available for download from the manufacturer's website: HobbyEagle A3 Pro V2 User Manual (PDF).

© 2026 HobbyEagle. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.