Introduction
The AODELAN PEBBLE is a versatile wireless remote shutter release designed to enhance your photography experience by minimizing camera shake and offering flexible control. It supports various shooting modes including autofocus, single shooting, continuous shooting, high-speed continuous shooting, BULB shooting, and a 3-second delay release. The device operates wirelessly up to 262 feet (80 meters) using 2.4GHz radio technology, and can also function as a wired remote.
Package Contents
Upon opening your AODELAN PEBBLE package, you should find the following items:
- 1 x Transmitter (with built-in CR2032 battery)
- 1 x Receiver
- 1 x Shutter Release Cable (specific to your camera model)
- 2 x Lanyards
Specifications
| Component | Specification |
|---|---|
| Transmitter Type | 2.4GHz wireless remote system |
| Transmission Power | 4dBm |
| Transmitter Battery | 1 x CR2032 button battery (built-in) |
| Transmitter Current | Sleep: 10uA, Stand-by: 10mA, Work: 15mA |
| Transmitter Size (L*W*H) | 66.8 * 35.8 * 13.2 mm |
| Transmitter Weight | 12.8 g (without battery) |
| Receiver Type | 2.4GHz |
| Receiver Battery | 2 x AAA battery (not included) |
| Receiver Current | Sleep: 10uA, Stand-by: 30mA, Work: 35mA |
| Receiver Size (L*W*H) | 89.6 * 41.0 * 32.6 mm |
| Receiver Weight | 36.5g (without battery) |
| Transmission Distance | 80M+ (262ft+) |
Compatibility
The AODELAN PEBBLE remote shutter release is compatible with a wide range of Nikon and Fujifilm camera models. Please ensure you select the correct shutter release cable (N8, N10, or N12) for your specific camera.
| Cable Type | Camera Brand | Compatible Models |
|---|---|---|
| N12 | Nikon | Z5 II, Z50 II |
| N8 | Nikon | Z8, Z9, D6, D5, D4s, D4, D3x, D3s, D3, D2Xs, D2X, D2Hs, D2H, D2, D1X, D1H, D1, D850, D810, D800, D800e, F90X, D700, D500, D300s, D300, D200 |
| Fujifilm | S5 Pro, S5, S3 | |
| N10 | Nikon | Z7 II, Z7, Z6 II, Z6, Z5, D780, D7500, D750, D7200, D7100, D7000, D610, D600, D5600, D5500, D5300, D5200, D5100, D5000, D3300, D3200, D3100, D90, Df, Coolpix A, P950, P1000, P1100, P7800, P7700 |
Setup
- Install Receiver Batteries: Open the battery compartment on the receiver unit and insert 2 AAA batteries (not included), ensuring correct polarity.
- Transmitter Battery: The transmitter comes with a built-in CR2032 button battery. Ensure it has sufficient power. You can check by pressing the Delay button; the indicator should turn red.
- Connect Receiver to Camera: Plug one end of the appropriate shutter release cable into the receiver and the other end into your camera's remote terminal.
- Mount Receiver (Optional): The receiver can be mounted on your camera's hot shoe or attached to a tripod.
- Power On: Press the power button on both the transmitter and receiver to turn them on. The LED indicators should light up.
Operating Modes
The AODELAN PEBBLE offers both wired and wireless operation, providing flexibility for various shooting scenarios. The 2.4GHz digital radio technology ensures a stable connection up to 80m (262ft) with 360° controllability.
Wired Operation (Receiver as Shutter Remote)
When the receiver is connected directly to the camera via the shutter release cable, it can function as a wired remote. Press the shutter button on the receiver to perform autofocus (half-press) and take a photo (full-press).
Wireless Operation
Ensure both the transmitter and receiver are powered on and properly connected to the camera.
- Single Shooting Mode:
- Set your camera to Single shooting mode.
- Half-press the shutter button on the transmitter to autofocus.
- Fully press the shutter button on the transmitter to take a single photo.
Single Shooting Mode Demonstration. - Continuous Shooting Mode:
- Set your camera to continuous shot mode.
- Press and hold the shutter button on the transmitter until its indicator turns off, then release the button. The camera will begin continuous shooting.
- To stop continuous shooting, press the shutter button on the transmitter again.
Continuous Shooting Mode Demonstration. - 3-Second Delay Shooting:
- Set your camera to Single shooting mode.
- Press the dedicated 3s delay button on the transmitter. The camera will trigger after a 3-second delay.
3-Second Delay Shooting Mode Demonstration. - Bulb Shooting Mode:
- Set your camera to BULB mode.
- Press and hold the shutter button on the transmitter for the desired exposure duration, then release it. The camera will perform BULB shooting for the duration the button was held.
- To end the exposure, press the shutter button on the transmitter again.
Bulb Shooting Mode Demonstration.
Maintenance
- Keep the remote control units dry. Do not expose them to moisture or rain.
- Clean the units with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
- Store the remote in a cool, dry place when not in use.
- If storing for an extended period, remove the AAA batteries from the receiver to prevent leakage.
- Ensure the battery in the transmitter (CR2032) is replaced when the indicator light becomes dim or unresponsive.
Troubleshooting
- Remote not triggering camera:
- Ensure both the transmitter and receiver are powered on.
- Check the batteries in both units. Replace if necessary.
- Verify that the shutter release cable is securely connected to both the receiver and the camera.
- Confirm that the camera is set to the correct shooting mode (e.g., Single, Continuous, Bulb).
- Ensure the camera's remote control settings are enabled, if applicable.
- Check the distance between the transmitter and receiver; ensure it's within the 80m range and there are no major obstructions.
- Intermittent connection:
- Move closer to the camera to rule out range issues.
- Check for potential sources of 2.4GHz interference (e.g., Wi-Fi routers, other wireless devices).
- Ensure batteries are fresh.
- Camera shake still present:
- Ensure you are using the remote for triggering, not manually pressing the camera's shutter button.
- For long exposures, use a sturdy tripod.
User Tips
- Battery Check: Always check the transmitter battery by pressing the Delay button; a red indicator confirms power.
- Multiple Cameras: The AODELAN PEBBLE can control multiple cameras simultaneously if each camera is equipped with its own receiver unit.
- Wired Backup: The receiver can be used as a wired remote if the transmitter battery dies or if wireless interference is an issue.
- Cable Selection: Double-check your camera model against the compatibility table to ensure you have the correct N-series cable for optimal performance.
Warranty & Support
AODELAN products are designed for reliability and performance. For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact AODELAN customer support through their official channels. Keep your purchase receipt as proof of purchase for warranty claims.
