ADVATEK PixLite R4D-S Long Range Receiver User Manual

Introduction

This is the user manual for the PixLite R4D-S pixel receiver, hardware version 1.3.

The PixLite R4D-S is designed to receive differential long distance signals of 300m (1000′) or more over a standard network cable from a PixLite T8 transmitter unit, and convert these input signals back into a pixel-ready signal for output directly to pixels.

The PixLite R4D-S features 4 data-only outputs, each having both a dedicated fuse and ‘fuse good’ LED indicator.

The PixLite R4D-S features a sleek, compact design and 4 holes for ease of wall mounting as well as an optional DIN rail mounting kit. It also features industrial grade  protection on all inputs and outputs, making it the ideal option for reliablecommercial and industrial applications.

This manual covers physical aspects of the PixLite R4D-S receiver and its essential setup steps only. Separate user manuals are available for the transmitter units. Other manuals may be downloaded from here: www.advateklighting.com/downloads

Safety Notes

Physical Installation

Wall Mount

Assemble the unit onto the wall / ceiling using four screws of a type suitable for the mounting surface (not supplied). The screws should be a pan head type, 3mm in thread diameter and at least 15mm long, as shown in Figure 1 below.
Figure 1: receiver Assembled to Wall

DIN Rail Mount

The receiver can be mounted to a DIN rail using the optional mounting kit (part number MNT0101).

Align the receiver’s mounting holes with the outermost mounting holes on each bracket. Using the four supplied M3, 12mm long screws, assemble the receiver to the mounting brackets, as shown in – DIN Rail Mount The receiver can be mounted to a DIN rail using the optional mounting kit (part number MNT0101).

1. Align the receiver’s mounting holes with the outermost mounting holes on each bracket. Using the four supplied M3, 12mm long screws, assemble the receiver to the mounting brackets, as shown in Figure 2 below. below.
   Figure 2: receiver Assembled to Bracket
   
2. Align the lower edge of the bracket with the lower edge of the DIN rail (1), and push the receiver down so it clicks onto the DIN rail (2), as shown in Figure 3 below.
   
   Figure 3: receiver Assembled to DIN Rail
3. To remove the receiver from the DIN rail, pull the receiver horizontally, toward its power connector (1) and rotate the receiver up and off the rail (2), as shown in Figure 4 below
   Figure 4: Removal of receiver from DIN Rail
   

Electrical Connections

Supplying Power
Power is applied to the PixLite R4D-S via the large lever clamp connector. The levers should be lifted up for wire insertion and then clamped back down, providing a highly robust and secure connection. Ensure the wire’s insulation is stripped back 11-12mm, so that the clamp does not rest on the insulation when closing the connector. Polarity for the connector is clearly marked on the lid, as shown in Figure 5 below. The type of wire required for supply connection is 4.0mm2 , 10AWG, V W-1.
Figure 5: Location of Power Input

Output Fuses & Power Injection

Each individual output is protected by a mini blade fuse. The PixLite R4D-S comes with 7.5A fuses by default. You may use any value of fuse, up to and including 7.5A, depending on your specific application. Individual outputs should not exceed 7.5A  and the total current should not exceed 30A. If your application requires more currentthan this, then you will need to inject power into the pixels directly.

The number of pixels that can be physically powered through this device may not be as high as the amount of pixel control data that is being output. There is no definitive rule as to how many pixels can be powered from the receiver, as it depends on the type of pixel. You need to consider if your pixel load will draw more than 7.5A of current and whether there will be too much voltage drop in the pixel load for it to only be powered from one end. If you need to “inject power” we recommend bypassing the receiver’s power output pins entirely.

If a fuse needs replacing, a suitable replacement fuse is of type “F7.5A E 32V”. An additional spare fuse is also provided for quick replacement which can be accessed by opening the lid, as shown in Figure 6 below
Figure 6: Internal View of the PixLite R4D-S

No on- board power configuration is required. Power to the logic circuitry is automatically regulated from the power input. Simply connect your DC power supply in accordance with specifications listed in Section 7.1 to the power screw terminal, as shown in Figure 5 above.

Data Input

Data is connected via a standard network cable into the RJ45 jack located on the front panel of the unit, as shown in Figure 7 below.
Figure 7: Position of Data Input

Receivers are connected to the transmitter via the RJ45 jacks on the rear panel of the PixLite T8. Each jack is labelled with its output number 1-8. These ports are not network ports, and should not be connected to any networking equipment, as shown in Figure 8 below. They are specifically designed to connect a PixLite transmitter with a PixLite receiver. For this reason, the standard network cable you use can be safely used in excess of 300m.
Figure 8: Correct equipment to use

A typical setup is shown in Figure 9 below, which also shows how many pixels can be run off each output.
Figure 9: Connecting Receivers to Transmitter

Connecting Pixel LEDs

The pixel lights are connected directly via the 4 pluggable screw terminal connectors on the rear of the unit. Each connector is labelled with its output channel number (1- 4) and on the top of the lid the pin-out is clearly marked. Simply wire your lights into each screw terminal and then plug them into the mating sockets. Since the PixLite R4D-S product has data only outputs (no pixel clock lines), it takes advantage of the transmitter’s Expanded Mode. In expanded mode, the clock lines are used as data lines instead. This means the receiver effectively has twice as many pixel outputs than the PixLite R2 (4), but half as many pixels per output can be run.

The cable length between the output and the first pixel should not exceed 15m.
Figure 10: Pixel Output Pinout

Operation

Start-up

When power is applied to the receiver, the green power led in the bottom right-hand corner on the front panel should be illuminated, as shown in Figure 11 below.
Figure 11: Position of the Power LED

If pixels have been correctly connected to the outputs and the data cable is connected to the transmitter and valid data is being sent, you should see the pixels turn on.

Indicator LEDs

Each fuse is paired with a green LED which indicates the condition of the fuse. If the fuse is good, the LED will be on. If the fuse has been blown or is not connected, the LED will be off. This feature offers a quick method for determining the state of each fuse, however in environments where these LEDs are needed to be turned off, a switch is located underneath the spare fuse that will turn off this feature. If the switch is pushed to the right, it is off, and all indicator LEDs and the power LED will always be off. This switch is shown in Figure 12 below.
Figure 12: Position of Indicator LEDs and Switch

Outputs

The number of pixels per output is configured in the transmitter device and may vary depending on the pixel capacity of the specific device.

The refresh rate of the pixels will depend on the operating frequency of the specific pixel chip type. Refer to the user manual of the PixLite Transmitter device for more information about this topic as the Transmitter will be responsible for the refresh rate of this receiver.

Specifications

Operating Specifications

Troubleshooting

No Power LED

Ensure that your power supply is supplying correct voltage. Additionally, ensure that it can supply enough current to drive the lights that are connected. You should also try disconnecting all outputs and see if the receiver then turns on.

Disclaimer

If you require support or warranty, please refer to Section 8.3 for information on creating a support ticket. You must be issued with a return authorization by Advatek support staff before returning any product.

The PixLite R4D- S receiver is supplied with a 3 – year limited warranty and a repair/replacement guarantee. Please see the terms and conditions on our website for more information.

The PixLite R4D-S has been tested against and independently certified as compliant with the Standards listed in the table below.

Documents / Resources

ADVATEK PixLite R4D-S Long Range Receiver [pdf] User Manual PixLite R4D-S Long Range Receiver, PixLite R4D-S, Long Range Receiver, Range Receiver, Receiver

References

• User Manual