ADVANTECH MIO-5152 Embedded Single Board Computers
Packing List
Before you begin installing your card, please make sure that the following items have been shipped:
- 1 x MIO-5152 SBC
- 1 x Startup manual p/n: 2046515200
- 1 x SATA cable p/n: 1700006291
- 1 x Audio cable p/n: 1700019584-01
- 6 x COM cable p/n: 1700030404-01
- 1 x USB cable p/n: 1700030406-01
- 1 x SATA power cable p/n: 1700031583-01
- 1 x Heatsink for x6000E p/n: 1970005053T001
- 1 x Heatsink for Celeron series p/n: 1970005053T011
- 1 x Device On package
If any of the above items are missing or damaged, contact your distributor or sales representative immediately.
Note 1: For more information regarding MIO-5152, refer to the Advantech website for further information.
Note 2: Acrobat Reader is required to view any PDF file. Acrobat Reader can be downloaded at: http://get.adobe.com/reader/ (Acrobat is a trademark of Adobe)
Specifications
General
- CPU:
- Intel® Celeron® J6412, 4 x cores, base frequency
2.0GHz; Max frequency 2.6GHz - Intel® Celeron® N6210, 2 x cores, base frequency
1.2GHz; Max frequency 2.6GHz - Intel® Atom® x6425E, 4 x cores, base frequency
2.0GHz; Max frequency 3.0GHz
- Intel® Celeron® J6412, 4 x cores, base frequency
- System Memory: Single channel, SODIMM DDR4-3200 MT/s, up to 32 GB
- CPU TDP:
- Celeron® J6412: 10W
- Celeron® N6210: 6.5W
- Atom® x6425E: 12W
- BIOS: AMI uEFI 256 Mbit
- Watchdog Timer: 255 levels timer interval, programmable by software. Multi-level WDT (set by iManager)
- Battery: Lithium 3 V/210 mAH
- Audio: High-definition audio (HD), line-in, line-out, & mic-in
Expansion Interface
- 1 x M.2 M-Key 2242
- 1 x M.2 E-Key 2230 (option to B-Key 3042)
Display
- Controller: Intel Gen 11 Graphics Engines (SoC integrated)
- Maximum Resolution:
- LCD: LVDS dual channel 18/24-bit up to 1920×1200
- DisplayPort: DP1.4a, up to 4096 x 2160 x 36bpp@60Hz
- HDMI: HDMI 1.4, up to 4096 x 2160 x 24bpp@60Hz
- Multiple display
- Triple simultaneous displays: LVDS + HDMI + DP
Ethernet Interface
- Speed: 10/100/1000 BASE-T
- Controller: 2 x Realtek RTL8111H
Mechanical and Environmentals Specs.
- Dimensions: 146 x 102 mm (5.7 x 4 in)
- Power Supply Type: ACPI support
- Power Requirements: +12 V ± 10% (Default supports ATX 2x2pin 90D, DC Jack by T-P/N)
- Operating Temperature: 0 ~ 60 °C (32 ~ 140 °F)
Jumpers and Connectors
The board has a number of jumpers that allow you to configure your system to suit your application. The table below lists the functions of each of the jumpers and connectors.
| Jumpers | |
| Label | Function |
| JCMOS1 | CMOS clear switch |
| VDD1 | Panel voltage selection |
| RI_VDD1 | COM1 RI# pin RI#/5V/12V selection |
| Connectors | |
| Label | Function |
| DCIN2 | DC input connector |
| DCIN1 | DC input connector (adapter) |
| LAN2 | RJ45 connector (1 x port) |
| LAN1 | RJ45 connector (1 x port) |
| USB56 | Internal USB connector |
| DP1 | DP connector |
| HDMI1 | HDMI connector |
| USB2 | USB 3.2 connector GEN2 (2 x ports) |
| USB1 | USB 3.2 connector GEN2 (2 x ports) |
| COM1 | COM port connector (RS232+RS422+RS485) |
| COM2 | COM port connector (RS232+RS422+RS485) |
| COM3~6 | COM port connector (RS232 only) |
| AUDIO1 | Audio connector |
| DIMMA1 | DDR4 SODIMM 260P/H9.2mm |
| LVDS1 | LVDS connector |
| SATA1 | HDD connector |
| SMB1 | SMB bus connector |
| FAN1 | FAN connector |
| SATAP1 | HDD power connector |
| BL1 | Inverter connector |
| PSON1 | ATX/AT mode selection |
| GPIO1 | GPIO connector |
| CN2 | Power/LED/case open/Buzzer connector |
| M2_B1 | M.2 Key B (PCIe_USB 2.0) |
| M2E1_1 | M.2 Key E (PCIe_USB 2.0) |
| M2_M1 | M.2 Key M (SATA) |
| BAT1 | RTC battery connector |
| SIM1 | SIM card connector |
Jumper Settings
| JCMOS1 | CMOS Clear Switch |
| Setting | Function |
| (1-2)* | Keep COMS data (Default) |
| (2-3) | Load CMOS date |
| VDD1 | Panel Voltage Selection |
| Setting | Function |
| (1-3)* | Panel voltage settings: +V3.3 (Default) |
| (3-5) | Panel voltage settings: +V5 |
| (3-4) | Panel voltage settings: +V12 |
| RI_VDD1 | COM1 RI# pin RI#/5V/12V Selection |
| Setting | Function |
| (1-2) | RI# Voltage settings: +V5 |
| (5-6) | RI# Voltage settings: +V12 |
| (3-4)* | RI# Voltage settings: RI# (Default) |
Caution!
The computer is provided with a battery-powered real-time clock circuit. Batteries are at risk of exploding if incorrectly replaced. Replace only with same or equivalent type as recommended by the manufacturer. Discard used batteries according to manufacturer’s instructions.
| PSON1 | ATX/AT Mode Selection |
| Setting | Function |
| (1-2) | AT |
| (2-3)* | ATX (Default) |
Connector Locations
Mechanical Drawings
Quick Installation Guide
There is a Heatsink in the white box, please remove the release paper from the thermal pads.
There are screws and stand-offs inside the box, follow the installation instructions demonstrated below to secure the heatsink:
CUSTOMER SUPPORT
MIO-5152 Intel® Atom® x6000E and Celeron® N and J series 3.5” SBC, DDR4, HDMI, DP, 2 x GbE, 4 x USB 3.2, M.2 E-key/B-Key, M.2 M-Key, 12V Power Input, iManager 3.0, & Edge AI Suite
Startup Manual
For more information about this and other Advantech
products, visit our website at
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and customer service, visit our
support website at
http://support.advantech.com
This manual is for the MIO-5152 Series.
Part No. 2046515200
Printed in China
Edition 1
Sep. 2021
Documents / Resources
 |
ADVANTECH MIO-5152 Embedded Single Board Computers [pdf] Instruction Manual MIO-5152, MIO-5152 Embedded Single Board Computers, Embedded Single Board Computers, Single Board Computers, Board Computers, Computers |
