Flare 2 Portable Speaker
User Manual

Safety Instructions

Avoid dropping.
Do not disassemble.
Avoid extreme temperatures.
Do not use the product outdoors during thunderstorms.
Use original or certified cables.
Do not use any corrosive cleaner/oil to clean.
Do not expose batteries to heat sources such as direct sunlight, fire and or the like.

At a Glance

1. Light effects button
2. Power button
3. Volume buttons ( – / +)
4. Multi-function button
5. Bass Boost button
6. Bluetooth & PartyCast button
7. USB-C charging port

Charging

• Use the included USB cable to charge your speaker and make sure it is fully charged before first use.
• Do not charge your speaker for extended periods.
• When not in use, store your speaker in a cool place.

Powering On/Off

Power on Press
Power off Press and hold for 2 seconds

Bluetooth Pairing

	Press	Enter Bluetooth pairing mode
	Flashing blue	Bluetooth pairing
	Steady blue	Bluetooth connected

• When powered on, the speaker will automatically connect to the last connected device if available within the Bluetooth range. If not, press the Bluetooth button to enter the Bluetooth pairing mode.
• To pair with another device, press the Bluetooth button to re-enter the pairing mode.

PartyCast Mode

Set up one Flare 2 as the primary speaker and connect it with more than 100+ secondary Flare 2 speakers to control audio and all the light effects.
Set up the primary speaker:

1. Connect one Flare 2 speaker to your phone or other devices via Bluetooth. When successfully connected, the Bluetooth LED will turn blue.
2. Press and hold the Bluetooth button on this Flare 2 for 3 seconds until you hear a sound and the Bluetooth LED flashes white to indicate this Flare 2 is the primary speaker.
   • The Bluetooth LED on the primary speaker will keep flashing white.

Connect with secondary speakers:

1. Make sure the secondary speakers aren’t connected to any Bluetooth devices.
   • Press the Bluetooth button to disconnect Flare 2 from a device, the Bluetooth LED will flash blue.
2. Press the Bluetooth button for 3 seconds until you hear a sound and the Bluetooth LED flashes white to indicate the secondary speaker is in connection mode.
3. When the secondary speakers are close to the primary speaker, they will connect to the primary speaker automatically. When successfully connected, the Bluetooth LED on the primary speaker will continue flashing white, while on the secondary speakers will turn white.

When successfully enter the PartyCast mode:

• you can power off, adjust the volume, or switch light effects for all speakers by controlling the primary speaker only;
• you can power off or switch light effects for each secondary speaker individually;
• you can’t adjust the volume for each secondary speaker individually;
• to exit the PartyCast mode, press the Bluetooth button either on the primary speaker or on the primary speaker for 3 seconds until the Bluetooth LED flashes blue.

Button Controls

Play / Pause		Press
Next track		Press twice
Previous track		Press thrice
Bass Boost On / Off		Press
Volume up / down		Press
Answer / End a call		Press
Reject a call		Press and hold for 2 seconds
Activate Siri or other voice assistant software		Press and hold for 2 seconds

Light Effects
Download the Soundcore App to check all available light effects.

Turn on / Switch light effects		Press
Turn off		Press and hold for 2 seconds

Soundcore App
Download the Soundcore App for light effects, EQ settings, firmware update and more.

Specifications

Specifications are subject to change without notice.

Input	5 V 2 A
Rated output power	2 x 10 W
Battery capacity	2600 mAh, 7.4 V
Charging time	3.5 hours
Playtime (varies by volume level and content)	12 hours
Frequency response	50 Hz – 20 kHz
Bluetooth version	V 5.0
Bluetooth range	20 m / 66 ft

Documents / Resources

soundcore Flare 2 Portable Speaker [pdf] User Manual Flare 2 Portable Speaker, Flare 2, Portable Speaker, Speaker

References

• User Manual