SEALEY SCR84.F Stand Handles

Specifications

• Model No: SCR84.F
• Nett Weight: 0.48kg

Product Information

Stand handles for the SCR84 and similar creepers, that allow the creeper to be stored vertically. Saving valuable space in a garage or workshop. Steel frame with powder coat paint finish. Simply connect to your existing creeper with a single bolt.

Product Usage Instructions

Assembly

1. 1. Remove the stand handles from the protective packaging.
   2. Lay the parts out on the floor and position the creeper ready to assemble the stand handles.
   3. Locate the mounting holes on the creeper’s frame.
   4. Attach one castor wheel to the bottom of the creeper’s frame, and one stand handle to the top of each side.
   5. Attach the supplied crush washer and lock nut to each castor wheel bolt. Tighten the lock nut using the supplied hex key wrench.

MaintenanceBefore each use, inspect the overall condition of the creeper for broken, cracked, or bent parts that may affect proper operation.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and properly maintained, give you years of trouble-free performance.

IMPORTANT:
 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

• Refer to the instructions

• Wear protective gloves

• Wear eye protection

SAFETY

• WARNING: Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using a creeper.
• Locate the creeper in a suitable working area.
• WARNING: Use a reeper on level and solid ground, preferably concrete.
• Keep the creeper clean and tidy by good workshop practice.
• DO NOT use the creeper for any purpose other than that for which it is designed.
• DO NOT stand on the creeper.
• DO NOT get the creeper wet or use in damp or wet locations or areas where there is condensation.
• DO NOT clean the creeper with any solvents that may damage the paint surface or padded areas.

INTRODUCTION
Stand handles for the SCR84 and similar creepers, that allow the creeper to be stored vertically. Saving valueable space in a garage or workshop. Steel frame with powder coat paint finish. Simply connect to your existing creeper with a single bolt.

ASSEMBLY

1. Remove the stand handles from the protective packaging.
2. Lay the parts out on the floor and position the creeper ready to assemble the stand handles.
3. Locate the mounting holes on the creeper’s frame. See fig.1.
4. Attach one castor wheel to the bottom of the creeper’s frame, and one stand handle to the top of each side. See fig.1.
5. Attach the supplied crush washer and lock nut to each castor wheel bolt. Tighten the lock nut using the supplied hex key wrench.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

• Note: It is our policy to continually improve products, and as such, we reserve the right to alter data, specifications, and parts without prior notice.
• Important: No Liability is accepted for incorrect use of this product.
• Warranty: The Guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

• 01284 757500
• sales@sealey.co.uk
• www.sealey.co.uk

FAQs

Q: What should I do if there are broken parts on the creeper?
A: If you notice any broken parts, do not use the creeper and contact customer support for assistance with replacement parts.

Q: Can I use the creeper on wet surfaces?
A: No, do not get the creeper wet or use it in da amp location, as it may cause damage.

Documents / Resources

SEALEY SCR84.F Stand Handles [pdf] User Guide SCR84.F, SCR84.F Stand Handles, SCR84.F, Stand Handles, Handles

References

• User Manual