JBL Go2

JBL Go2
What’s in the box

Buttons

Connections

Bluetooth®
- Bluetooth connection

- Music control

Speakerphone

LED indication

Warning

JBL GO 2 is IPX7 waterproof
IMPORTANT: To ensure that the JBL GO 2 is waterproof, please remove all cable connections and tightly close the cap; exposing the JBL GO 2 to liquids without doing so may result in permanent damage to the speaker. And do not expose JBL GO 2 to water while charging, as doing so may result in permanent damage to the speaker or power source.
IPX7 waterproof is defined as the speaker can be immersed in water up to 1m for up to 30 minutes.
Specifications
- Bluetooth version: 4.1
- Bluetooth Profile: A2DP v1.2 AVRCP v1.5 HFP v1.6, HSP v1.2
- Transducer: 1 x 40mm
- Rated power: 3W
- Frequency response: 180Hz – 20kHz
- Signal-to-noise ratio: 80dB
- Battery type: Lithium-ion polymer (3.7V, 730mAh)
- Battery charge time: 2.5Hours
- Music playing time: up to 5 hours (varies by volume level and audio content)
- Bluetooth transmitter power: 0~4dBm
- Bluetooth transmitter frequency range: 2402~2480MHz
- Bluetooth transmitter modulation: GFSK/DQPSK/8DPSK
- Dimensions: 71.2 x 86.0 x 31.6 (mm)
- Weight: 130g

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.
DOWNLOAD RESOURCES
FAQ’S
The JBL GO 2 is an ultra-compact speaker that’s waterproof and can really take a beating. While its small size limits its audio performance potential, it can get surprisingly loud and has a handy speakerphone that help make it one of the most well-rounded ultra-compact speakers on the market.
As far tiny speakers go, sound quality is relatively good. I compared it to the original Go and the Go 2 plays a little louder with more bass. Even so, as you might expect, this speaker overall is short on bass and won’t exactly rock a room, even a small one.
The IPX7 waterproof housing makes GO 2 perfect for worry-free listening by the beach or poolside, or even in it.
Yes, it has its own mic near the charger port so it’s perfect for calls!. No need for an app, you can simply connect our JBL Go 2 via Bluetooth. A: You can get up to 5 hours of music play time but will depend on your volume level and audio content.
Yes. JBL Go 2 can be used while charging. This will not affect the battery since it is lithium-ion and it has a PCM circuit. The speaker will automatically switch to trickle charging when the battery is full.
How do I check the battery level of My JBL Go 2? Simply look at the LED indicator on the front of the speaker. If it is blinking in red, then it means that the battery is low and requires charging.
The JBL Go red light problem occurs when you charge the speaker or remove it from the charger, especially when you charge it using a wall plug. In this case, the speaker does not work and does not respond to anything only the indicator LED lights in red.
3 Watt.
The main difference is that GO 2 has a built-in battery so you can take it anywhere, and it has a built-in microphone for hands-free calling.
Yes. You can listen to your own headphones using the 3.5mm stereo mini jack on the side of the speaker.
Press the power button on top of the speaker to turn it on or off. If you press and hold the power button for more than 3 seconds, you will put your speaker into pairing mode.
You can adjust the volume by pressing + or – buttons on top of the speaker or by using your device’s volume control. If you press and hold + or – buttons for more than 1 second, you will fast forward or rewind your music track.
VIDEO
www://uk.jbl.com/
References
- User Manualmanual.tools

Help please. I have paired my new jbl go2 with my samsung phone and tablet. I can listen to music from my tablet. But I can’t get anything from my phone. Can both be connected at the same time?What do I need to do?
Can the JBL Go 2 connect to two devices simultaneously, and how do I switch between them?
The JBL Go 2 does not support "Multipoint" technology, which means it cannot be actively connected to two devices at the same time. While you can have the speaker paired with both your Samsung phone and tablet, it can only maintain an active audio stream from one device at a time.
To switch from your tablet to your phone, follow these steps:
If the speaker does not automatically become available for the phone, you can briefly press the Bluetooth button on the top of the speaker to enter pairing mode again, then select it on your phone.
Note: Always ensure that the device you are not using has its Bluetooth turned off or is disconnected to prevent it from "holding" the connection and blocking the other device.
>
Read the full Q&A page
My JBL GO 2 problem
While night time fully charged but morning we don’t use the speaker .
Buttons no working .
Only LED light on in red color
What we do??
Hello, the same thing happens to me, red light on and nothing works, I can’t turn it off or reset it either.
Hola, a mi mesucede lo mismo, luz roja encendida y nada funciona, tampoco lo puedo apagar ni resetear.
press power button for 20 seconds.
so easy!!!
MERCI!!!
Okay that’s good ! Thank you
OK C’est bon ! Merci
The red LED is constantly lit and the buttons do not respond to anything.
Folyamatosan világít a piros LED, és a gombok semmire se reagálnak.
press the power button for 20-30 seconds.. it should
solve this pb
appuyez sur le bouton d’alimentation pendant 20 à 30secondes.. ça devrait
résoudre ce pb
No. I had same problem and the Argos Product Support line helped a lot. I had to stop all my devices recognising the Go2 then ask for one to recognise it again.. . Even just switching off the bluetooth on the device did not allow it to work with another device.
Can the JBL Go 2 connect to two devices simultaneously, and how do I switch between them?
No. I had same problem and the Argos Product Support line helped a lot. I had to stop all my devices recognising the Go2 then ask for one to recognise it again.. . Even just switching off the bluetooth on the device did not allow it to work with another device.
Only one at a time.
Can the JBL Go 2 connect to two devices simultaneously, and how do I switch between them?
Only one at a time.
TheGO2 Speaker is connected via Analog cable and keeps going off, how do I keep it on?
How do I prevent the JBL Go 2 from automatically turning off when using an analog cable connection?
The JBL Go 2 features an automatic power-saving function (Auto-Off) that triggers if it does not detect a strong enough audio signal for a period of time (usually around 10 to 20 minutes). When using an analog cable (3.5mm AUX), the speaker may turn off if the source volume is too low.
To keep the speaker from turning off, try the following:
Note: The manual does not provide a way to manually disable the Auto-Off power-saving feature as it is hardcoded into the device's firmware to preserve battery life.
Read the full Q&A page
Did you have got this problem solved?
I have the same issue
How to charge the Go2?
How do I charge the JBL Go 2 speaker?
To charge your JBL Go 2, follow these steps:
Important Safety Note: To prevent permanent damage, ensure the speaker is completely dry and all cable connections are removed before exposing it to water. Do not charge the speaker while it is wet or near water.
Read the full Q&A page
Hello, I’ve just bought the very good JBL GO 2. It’s great but….
Why can’t I play it while it’s charging, it just switches off when I try to play music in the charge mode
Why can’t I play it while it’s charging, it just switches off when I try to play music in the charge mode
Why does my JBL GO 2 switch off when I try to play music while it is charging?
According to the product documentation, the JBL GO 2 can be used while charging. It features a lithium-ion battery with a PCM circuit that allows for trickle charging once the battery is full without damaging the unit.
If your speaker is switching off specifically when you try to play music in charge mode, please consider the following troubleshooting steps:
If the device continues to shut down despite using a known good power adapter and cable, there may be an internal hardware fault with the charging circuit or battery.
Read the full Q&A page
I have a GO2.
How do I connect it to my tablet via blue tooth to receive amazon music?
How do I connect it to my tablet via blue tooth to receive amazon music?
How do I connect my JBL Go2 to a tablet via Bluetooth to play Amazon Music?
To connect your JBL Go2 to your tablet and start listening to Amazon Music, follow these steps:
Note: If you have trouble finding the device, you can also try pressing and holding the power button for more than 3 seconds to force the speaker into pairing mode.
Read the full Q&A page
I am replacing my BROKEN laptop speakers with a JBL GO2.
Is there a way to KEEP the GO2 on all the time without having it turn off automatically. I keep the power cord plugged in at all times.
Thank you.
Is there a way to KEEP the GO2 on all the time without having it turn off automatically. I keep the power cord plugged in at all times.
Thank you.
How can I disable the automatic power-off feature on the JBL GO2 to keep it on at all times?
The JBL GO2 features an automatic power-saving mode that turns the device off after approximately 10 to 15 minutes of inactivity (no audio signal), even if it is plugged into a power source. This is a built-in firmware feature designed to conserve energy and protect the battery.
Unfortunately, the official manual and technical specifications do not provide a method to disable this auto-off feature. To keep the speaker from turning off, it must receive a constant audio signal. If you are using it with a laptop, you may need to ensure there is consistent audio playback, or you will have to manually power the speaker back on using the Power button on top of the device after periods of silence.
Read the full Q&A page
I ‘ve got two Go2’s can I pair them up to each other for more Sound ala stereo??? If so what cable do I need . Thanks
How can I pair two JBL Go 2 speakers together for stereo sound, and what cable is required?
The JBL Go 2 does not support wireless pairing features like "JBL Connect+" or "PartyBoost," which means you cannot pair two of them together wirelessly via Bluetooth for stereo sound.
To achieve a dual-speaker setup, you would need to use a physical 3.5mm Y-splitter cable (one male 3.5mm plug to two male 3.5mm plugs). You would plug the single end into your audio source (like a phone or laptop) and the two split ends into the 3.5mm auxiliary input ports located under the protective cap on each JBL Go 2. Note that this will provide dual-mono sound rather than true stereo unless you use a specific stereo-to-dual-mono splitter.
Read the full Q&A page
After I charged my JBL Go2 Speaker and disconnected it from the powersource, the LED is still red (permanently). The Box is not reacting to any pressed buttons. Even after several hours after disconnecting from the charger the LED is red, as of it would still charge.
Why is my JBL Go2 LED stuck on red and the speaker unresponsive after charging?
This issue, where the LED remains solid red and the speaker becomes unresponsive to button presses, is a known state that can occur after charging. To resolve this, you should perform a manual reset to force the device to reboot.
If the red light persists even after attempting a long-press of the power button, let the battery drain completely until the light goes out on its own, then try charging it again using a different USB cable or a different power adapter (such as a computer USB port instead of a wall plug) to rule out a charging circuit error.
Read the full Q&A page
I have the same problem. Did you find a solution for this?
Press and hold the power button until the red light goes off, about 20 seconds. The best way to find answers is to enter the device name and add troubleshooting to your search.
Why is my JBL Go2 LED stuck on red and the speaker unresponsive after charging?
Press and hold the power button until the red light goes off, about 20 seconds. The best way to find answers is to enter the device name and add troubleshooting to your search.
Neither 20, nor 30, 40 or 50 seconds. The light remains red. And where to find answers? Whose troubleshooting?
I don’t know what happened but my JBL go only connects to my cell phone to my partner’s, it no longer connects to the computer when it did before. of rependen the compus of my house no longer detect it! I have two notebooks and both have bluetooth but for some reason they do not detect the device. what can be done?
No se que pasó pero mi JBL go solo se conecte a mi celular al de mi pareja, ya no se conecta a la compu cuando antes si lo hacia. de rependen las compus de mi casa ya no lo detectan! tengo dos notebooks y ambas tienen bluetooth pero x alguna razon no lo detectan al aparato. q se puede hacer?
No se que pasó pero mi JBL go solo se conecte a mi celular al de mi pareja, ya no se conecta a la compu cuando antes si lo hacia. de rependen las compus de mi casa ya no lo detectan! tengo dos notebooks y ambas tienen bluetooth pero x alguna razon no lo detectan al aparato. q se puede hacer?
Why is my JBL Go 2 not being detected by my computers via Bluetooth even though it connects to phones?
It is common for the JBL Go 2 to remain "locked" to the last connected device (like your phone), which prevents other devices like your computers from seeing it. To fix this, you need to manually trigger pairing mode:
Read the full Q&A page
My ipad (Air 3) can’t control volumn GO2 on it and speaker too 🙁 But my iphone can do it.
Why can't I control the volume of my JBL Go2 using my iPad Air 3, even though it works with my iPhone?
If your iPad Air 3 is unable to control the volume of the JBL Go2, while your iPhone works correctly, it suggests a software or connection sync issue rather than a hardware fault with the speaker. Please try the following steps:
Read the full Q&A page
How do I get rid off the extremely unwelcome on and off sounds?
How do I disable the power on and off notification sounds on the JBL Go 2?
Based on the official manual and technical specifications for the JBL Go 2, there is no built-in setting or button combination to disable the power on/off notification sounds. These audio cues are part of the device's firmware to indicate power status and Bluetooth connectivity.
While some larger JBL speakers support sound customization via the JBL Portable app, the JBL Go 2 is not compatible with the app and does not offer a way to mute these specific alerts. To minimize the impact of the sound, ensure your connected device's volume is lowered before turning the speaker off, though the startup chime typically plays at a fixed default volume.
Read the full Q&A page
“After I charged my JBL Go2 Speaker and disconnected it from the powersource, the LED is still red (permanently). The Box is not reacting to any pressed buttons. Even after several hours after disconnecting from the charger the LED is red, as of it would still charge.”
Exactly the same happened to me, right after the first charging, and the box has been “dead” for almost 24h now. Was that it? If yes… What a miserable quality!
Exactly the same happened to me, right after the first charging, and the box has been "dead" for almost 24h now. Was that it? If yes... What a miserable quality!
Why is my JBL Go2 stuck with a permanent red LED and unresponsive to buttons after charging?
The issue you are describing, where the LED remains solid red and the speaker is unresponsive after charging, is a known state often referred to as the "red light problem." This typically occurs when the device's internal software hangs during or after a charging cycle.
To resolve this, you should try a Hard Reset to force the device to reboot:
If the red light remains on and the device stays "dead" for more than 24 hours, the battery or the internal charging circuit may have failed. Since you mentioned this happened right after the first charge, it is highly recommended to contact JBL support or the retailer for a warranty replacement, as this behavior is not normal for a new unit.
Read the full Q&A page
I have the same problem. Did you find a solution for this?
Hold it down until it finally turns off, it worked for me.
Mantenlo presionado hasta que por fin se apague, a mi me resulto.
Mantenlo presionado hasta que por fin se apague, a mi me resulto.
Why is my JBL Go2 stuck with a permanent red LED and unresponsive to buttons after charging?
Hold it down until it finally turns off, it worked for me.
Mantenlo presionado hasta que por fin se apague, a mi me resulto.
cant seem to turn on my jbl go2, its stuck in its charging state even though ive already removed the charger.
How do I fix a JBL Go 2 that is stuck in a charging state and won't turn on?
It appears your JBL Go 2 is experiencing a common issue where the device becomes unresponsive and the LED remains lit (often red), indicating it is stuck in a charging or software-locked state. To resolve this, you should attempt a hard reset:
If the speaker still does not respond, ensure you are using a functional micro-USB cable and a standard 5V power adapter. If the red light persists and the speaker will not turn on after a reset, there may be a hardware fault with the battery or the internal PCM circuit.
Read the full Q&A page
How do you actually use it? The instructions don’t tell you at all. I have guessed you have to charge it but then what?
How do I use the JBL Go 2 speaker after charging it?
To use your JBL Go 2 after charging, follow these basic steps:
Note: If you prefer a wired connection, you can plug an audio cable into the 3.5mm jack located under the protective side flap.
Read the full Q&A page
Hello,
same question as Max, how to suppress too loud on and off sounds?
Bonjour,
même question que Max, comment supprimer les sons d’activation et de désactivation beaucoup trop bruyants ?
same question as Max, how to suppress too loud on and off sounds?</i>
Bonjour,
même question que Max, comment supprimer les sons d'activation et de désactivation beaucoup trop bruyants ?
How can I disable or lower the volume of the power on and off notification sounds on the JBL Go2?
Based on the official manual and technical specifications for the JBL Go2, there is no built-in setting or button combination to disable or lower the volume of the power-on and power-off notification sounds.
These audio alerts are programmed into the device's firmware at a fixed volume level and cannot be adjusted by the user. While some newer or larger JBL models support sound customization via the JBL Portable app, the JBL Go2 does not have app support and lacks this feature.
If you find the sounds too disruptive, the only known workaround is to cover the speaker grille with a cloth or your hand while turning it on or off to physically muffle the sound.
Read the full Q&A page
I wanted turn on this without ‘wake-up’ sound?
How can I cut it .?
How can I cut it .?
How can I disable the startup or wake-up sound on the JBL Go 2?
Based on the official JBL Go 2 manual and technical specifications, there is no built-in setting or button combination to disable the startup (wake-up) or shutdown sounds. These audio cues are part of the device's firmware to indicate power status.
While some newer or larger JBL models support disabling "Audio Feedback" via the JBL Portable app, the JBL Go 2 is not compatible with the JBL app and does not offer this customization. To minimize the sound, you can try covering the speaker with a soft cloth while turning it on, but the volume of the startup chime is generally fixed and independent of the music volume setting.
Read the full Q&A page
My jbl go 2 speaker, when not plugged in, still shows the light is charging. So what is that error?
Thank you.
Loa jbl go 2 của em khi không cắm sạc nó vẫn hiện đèn báo là đang sạc. Vậy đó là lỗi gì vậy ạ
Em cảm ơn.
Thank you.</em>
Loa jbl go 2 của em khi không cắm sạc nó vẫn hiện đèn báo là đang sạc. Vậy đó là lỗi gì vậy ạ
Em cảm ơn.
Why does my JBL Go 2 speaker show a charging light even when it is not plugged in?
If your JBL Go 2 shows a charging light (typically a solid red LED) even when it is not plugged in, this usually indicates a software hang or a hardware fault in the charging circuit. You can try the following steps to resolve the issue:
If the red light remains on and the speaker becomes unresponsive to buttons, it may indicate a internal hardware failure or a depleted battery cell that requires professional service.
Note: The manual indicates that a blinking red light means low battery, while a solid red light during charging should turn off once fully charged. A persistent light when unplugged is not standard behavior.
Read the full Q&A page
I wonder why I do not find an answer anywhere. Many questions about the expected red light and what happens when it does not light up, but the answer is nowhere to be found
Απορω γιατι δεν βρισκω απάντηση πουθενα. Πολλα ερωτηματα για το αναμενο κοκκινο λαμπακι και τι γινεται που δεν αναβει, αλλα η απαντηση δεν υπαρχει πουθενα
Απορω γιατι δεν βρισκω απάντηση πουθενα. Πολλα ερωτηματα για το αναμενο κοκκινο λαμπακι και τι γινεται που δεν αναβει, αλλα η απαντηση δεν υπαρχει πουθενα
Why is the red LED not lighting up on my JBL Go 2, and what does it mean when it stays red?
Based on the JBL Go 2 manual and troubleshooting data, here is the breakdown of the red LED behavior:
Always ensure the charging port is dry and the protective cap is closed when not charging to prevent damage.
Read the full Q&A page
So I purchased this GO2 speaker yesterday. Not impressed with the packaging as in: the sheets of paper info rolled up and stuffed into a small box, which have to be flattened out. Then there are NO instructions on how to set this thing up. Not even info saying you can download a manual. Why should I have to do that? Instructions should be included. So can you send me a copy of the instructions.
How do I set up and use the JBL Go 2 speaker?
Setting up your JBL Go 2 is straightforward. Here are the basic instructions to get you started:
You can view or download the full digital manual directly from this page for more detailed information.
Read the full Q&A page
I have connected for two hours. No red charging light appears. It does not turn on.
Tengo conectado hace dos horas. No aparece luz roja de carga. No se enciende.
Tengo conectado hace dos horas. No aparece luz roja de carga. No se enciende.
Why is my JBL Go 2 not charging or turning on after being plugged in for two hours?
If your JBL Go 2 is not showing a red charging light and will not turn on, please try the following troubleshooting steps:
Note: The JBL Go 2 takes approximately 2.5 hours to reach a full charge. If the device remains unresponsive after trying a known-working cable and charger, the battery or internal hardware may require professional service.
Read the full Q&A page
I have the same problem too.
Press the power button
presiona el boton de encendido
presiona el boton de encendido
Why is my JBL Go 2 not charging or turning on after being plugged in for two hours?
Press the power button
presiona el boton de encendido
it is impossible for me to connect the jbl go2 speaker to my computer which is under windoos 10, if on tours 37 there is someone who has the solution thank you
il m’est impossible de connecter l’enceinte jbl go2 a mon ordi qui est sous windoos 10, si sur tours 37 il y a une personne qui a la solution merci
il m'est impossible de connecter l'enceinte jbl go2 a mon ordi qui est sous windoos 10, si sur tours 37 il y a une personne qui a la solution merci
How do I connect my JBL Go2 speaker to a Windows 10 computer via Bluetooth?
To connect your JBL Go2 to a Windows 10 computer, follow these steps:
If the speaker is still not appearing, ensure it is not currently connected to another device (like a smartphone), as it can usually only maintain one active connection. You may also need to check your Windows Sound Settings to ensure the JBL Go2 is selected as the Default Output Device once paired.
Read the full Q&A page
OLA, I have the situation of many of the previous users, normal work at the beginning, today when I put it the red light remained on, and I put the charging cable. And it was blocked, the bluetooh lights up the indicator but it does not work, the power button registers on and off, but does not sound in connection with the bluetooh.
OLA, tengo la situación de muchos de los anteriores usuarios, trabajo normal al principio, hoy al ponerlo quedó la luz roja encendida fija, y coloque el cable de carga . Y quedó bloqueado, el bluetooh, alumbra el testigo pero no funciona, botón de encendido registra prendido y apagado, pero no suena en conexión con bluetooh.
OLA, tengo la situación de muchos de los anteriores usuarios, trabajo normal al principio, hoy al ponerlo quedó la luz roja encendida fija, y coloque el cable de carga . Y quedó bloqueado, el bluetooh, alumbra el testigo pero no funciona, botón de encendido registra prendido y apagado, pero no suena en conexión con bluetooh.
How do I fix my JBL Go 2 if it is blocked with a solid red light and won't play sound via Bluetooth?
The issue you are describing, where the speaker remains stuck with a solid red light and becomes unresponsive (blocked) even though it appears to power on, is a known state that often requires a hardware reset. To resolve this, please try the following steps:
If the red light continues to stay on and the speaker does not respond to the button combination, let the battery drain completely until the light goes out, then recharge it fully before attempting to turn it on again.
Read the full Q&A page
I have no idea where to begin to set up my bo2 jbl speaker. Can you please help?
How do I set up my JBL Go 2 speaker?
Setting up your JBL Go 2 is a simple process. Follow these steps to get started:
Important Note: To maintain the IPX7 waterproof rating, ensure the side cover protecting the charging and AUX ports is tightly closed before exposing the speaker to water.
Read the full Q&A page
Hi guys,
I seem to have some problem with JBL go2.
Got it brand new and it only works while it’s connected to the charger.
There is only white LED color, no blue, no red colors.
As soon as I disconnect it from the charger it turns off.
Any solutions for this ?
I seem to have some problem with JBL go2.
Got it brand new and it only works while it's connected to the charger.
There is only white LED color, no blue, no red colors.
As soon as I disconnect it from the charger it turns off.
Any solutions for this ?
Why does my JBL Go 2 only work when plugged in and show a solid white LED?
Based on the behavior you described, your JBL Go 2 is likely experiencing a battery failure or a power circuit issue. Under normal operation, the LED should show blinking red when the battery is low and solid red while charging, turning off once fully charged.
The fact that it only stays powered while connected to a charger suggests the battery is unable to hold a charge. Since you mentioned the device is brand new, please try the following steps:
Read the full Q&A page
I have a problem with my jbl go2 for a long time it refuses to turn on and during charging it automatically turns on but does not respond because when I turn on my bleuthoof it refuses to connect … But the light is always on
J’ai un problème avec mon jbl go2 depuis un bon moment il refuse de s’allumer et pendant la charge il s’allume automatiquement mais ne répond pas car quand je mets mon bleuthoof en marche il refuse de ce connecter… Mais le voyant est toujour en marche
J'ai un problème avec mon jbl go2 depuis un bon moment il refuse de s'allumer et pendant la charge il s'allume automatiquement mais ne répond pas car quand je mets mon bleuthoof en marche il refuse de ce connecter... Mais le voyant est toujour en marche
Why does my JBL Go 2 only work when plugged in and show a solid white LED?
I have a problem with my jbl go2 for a long time it refuses to turn on and during charging it automatically turns on but does not respond because when I turn on my bleuthoof it refuses to connect ... But the light is always on
J'ai un problème avec mon jbl go2 depuis un bon moment il refuse de s'allumer et pendant la charge il s'allume automatiquement mais ne répond pas car quand je mets mon bleuthoof en marche il refuse de ce connecter... Mais le voyant est toujour en marche
I have the same problem
J’ai le même problème
MY JBL GO2 IS NOT CONNECTING THE BLUETOOTH WITH MY ANDROID, HOW SHOULD I RECONNECT?
O MEU JBL GO2, NÃO ESTA CONECTANDO O BLUETOOTH COM O MEU ANDROID, COMO DEVO RECONECTAR?
O MEU JBL GO2, NÃO ESTA CONECTANDO O BLUETOOTH COM O MEU ANDROID, COMO DEVO RECONECTAR?
How do I reconnect my JBL Go2 to my Android device via Bluetooth?
To reconnect your JBL Go2 to your Android device, follow these steps to re-enter pairing mode:
If the device was previously paired but is not connecting, try "Forgetting" or "Unpairing" the JBL GO 2 from your Android Bluetooth settings first, then repeat the steps above to establish a fresh connection.
Read the full Q&A page
How do I charge the JBL go2? Is there a charger? Nothing was included.
Wie lade ich das JBL go2? Gibt es ein Ladegerät? Es wurde nichts mitgeliefert.
Wie lade ich das JBL go2? Gibt es ein Ladegerät? Es wurde nichts mitgeliefert.
How do I charge the JBL Go2 and is a charger included?
To charge your JBL Go2, locate the charging port under the protective cap on the side of the speaker. Connect a Micro USB cable to this port and plug the other end into a USB power source (such as a computer or a USB wall adapter).
Important: Always ensure the charging port is completely dry before plugging in the cable, and keep the protective cap tightly closed when not charging to maintain the speaker's IPX7 waterproof rating.
Read the full Q&A page
Btooth connected phone came out of range, connection disconnected of course .. but now I can not turn on the speaker again .. just flashes white once… but does not turn on… I can continue to “turn it on” but it goes out immediately ..
anyone know what it takes to get that little rogue back on track? 🙂
Btooth forbundet telefon kom udenfor rækkevidde, forbindelsen afbrudt naturligvis.. men nu kan jeg ikke tænde højttaleren igen.. blinker blot en enkelt gang hvidt… men tænder ikke… jeg kan blive ved med at “tænde den” men den går ud med det samme..
nogen som ved hvad der skal til for at få den lille slyngel tilbage på sporet? 🙂
anyone know what it takes to get that little rogue back on track? :-)<e/em>
Btooth forbundet telefon kom udenfor rækkevidde, forbindelsen afbrudt naturligvis.. men nu kan jeg ikke tænde højttaleren igen.. blinker blot en enkelt gang hvidt… men tænder ikke… jeg kan blive ved med at “tænde den” men den går ud med det samme..
nogen som ved hvad der skal til for at få den lille slyngel tilbage på sporet? :-)
Why does my JBL Go 2 flash white once and turn off immediately after losing Bluetooth range?
It sounds like your JBL Go 2 may be stuck in a software hang or is experiencing a power-state error after the sudden disconnection. To get the speaker back on track, please try the following steps:
If the speaker continues to flash white once and shut down even while connected to a charger, the internal battery or circuit board may have failed.
Read the full Q&A page
Can we turn off weird sounds on or off?
Dajú sa vypnúť divné zvuky pri zapnutí alebo vypnutí?
Dajú sa vypnúť divné zvuky pri zapnutí alebo vypnutí?
Can I turn off the startup and shutdown sounds on the JBL Go 2?
Based on the official manual and technical specifications for the JBL Go 2, there is no built-in setting or button combination to disable the startup and shutdown sounds (audio feedback). Unlike some larger JBL models that use the JBL Portable app, the JBL Go 2 does not support app connectivity to toggle these sounds off.
The sounds are a standard feature of the device's firmware to indicate power status and Bluetooth connectivity. If you find the sounds too loud, please note that their volume is generally fixed and does not change based on the speaker's music volume level.
Read the full Q&A page
my go 2 connecs and the volume and other buttons working but it is like to be mute. there is no sound of it
Why is my JBL Go 2 connected and the buttons working, but there is no sound?
If your JBL Go 2 is connected and the buttons are responsive but there is no sound, please try the following troubleshooting steps:
Read the full Q&A page
My speaker when I connect my cell phone plays for seconds and then turns off
Mi bocina al conectar mi celular toca por segundos y luego se apaga
Mi bocina al conectar mi celular toca por segundos y luego se apaga
Why does my JBL Go 2 speaker turn off after a few seconds of playing music from my phone?
If your JBL Go 2 turns off shortly after starting playback, please check the following troubleshooting steps:
Read the full Q&A page
Hello, my problem is that the moment indicator turns on and then turns off and end, what will be the problem?
Здравейте моят проблем е че индикатора за миг се включва и после изключва и край,какъв ли ще е проблемът?
Здравейте моят проблем е че индикатора за миг се включва и после изключва и край,какъв ли ще е проблемът?
Why does the indicator light on my JBL Go2 turn on briefly and then immediately turn off?
If your JBL Go2 indicator light turns on briefly and then shuts off, it usually indicates one of the following issues:
If the speaker is unresponsive, you can try a factory reset: While the device is on, press and hold the Volume + and Bluetooth buttons simultaneously for about 3 seconds until the speaker turns off. Then try turning it back on.
Read the full Q&A page
My jbl won’t charge. White light while plugged in. Tried holding the plus and triangle button together for 10 sec and nothing.
Why won't my JBL Go 2 charge, and why is there a solid white light when plugged in?
If your JBL Go 2 shows a solid white light while plugged in but is not charging or turning on, it may be stuck in a software hang or experiencing a battery fault. Please try the following steps:
If the speaker remains unresponsive after trying a different cable and the Volume Up + Bluetooth reset, the hardware may require professional service.
Read the full Q&A page
My GO2 is not Charging. What should I do?
No Light at All.
No Light at All.
What should I do if my JBL Go 2 is not charging and the LED indicator does not light up?
If your JBL Go 2 is not charging and shows no light at all, please try the following troubleshooting steps:
If the device remains completely dark after trying multiple cables and chargers, the internal battery or charging circuit may have failed, and you may need to contact JBL support for repair options.
Read the full Q&A page
What are the signs that the JBL Go 2 battery is fully charged? Please explain because I don’t know it yet.
Apa tandanya jika baterai JBL Go 2 sudah penuh mengisi baterai? Mohon penjelasannya karena saya belum mengetahuinya.
Apa tandanya jika baterai JBL Go 2 sudah penuh mengisi baterai? Mohon penjelasannya karena saya belum mengetahuinya.
What are the signs that the JBL Go 2 battery is fully charged?
To determine the battery status of your JBL Go 2, observe the LED indicator light located on the front of the speaker:
According to the manual, a full charge typically takes approximately 2.5 hours. The speaker also features a PCM circuit that automatically switches to trickle charging once the battery is full, so it is safe to leave it connected to the power source.
Read the full Q&A page
I have used my jbl go 2 for a year and everything is fine, but suddenly I started to charge it and it usually takes 2 to 3 hours to fully charge and it turns out that now many hours pass and it never finishes charging. and then i unplug it and it sounds like 1 hour or so and it goes off.
he usado mi jbl go 2 durante un año y todo bien, pero derepente lo empeze a cargar y generlmente se demora 2 a 3 hrs en carga completa y resulta que ahora pasan muchas hora y no se termina de cargar nunca. y luego lo desconecto y suena como 1 hora aprox y se apaga.
he usado mi jbl go 2 durante un año y todo bien, pero derepente lo empeze a cargar y generlmente se demora 2 a 3 hrs en carga completa y resulta que ahora pasan muchas hora y no se termina de cargar nunca. y luego lo desconecto y suena como 1 hora aprox y se apaga.
Why is my JBL Go 2 taking many hours to charge and only lasting for one hour of playtime?
Based on your description, it appears the internal Lithium-ion polymer battery in your JBL Go 2 is reaching the end of its usable life or has developed a fault. Under normal conditions, the speaker should take approximately 2.5 hours to fully charge and provide up to 5 hours of playtime.
Since you have owned the device for a year and it now fails to complete a charge cycle while only lasting about an hour, you may want to try the following troubleshooting steps:
If these steps do not improve the charging time or battery life, the battery has likely degraded. Because the JBL Go 2 is a sealed, IPX7 waterproof unit, the battery is not user-replaceable without compromising the device's water resistance. If the product is still under warranty, it is recommended to contact JBL support for a repair or replacement.
Read the full Q&A page
Hello good day!
My box doesn’t have a bluetoo button, just a letter M instead.
Does that mean I can’t connect to my cell phone?
I was able to listen to just a pendrive, great sound.
Olá bom dia!
Minha caixa não tem botão bluetoo, só uma letra M no lugar.
Quer dizer q não consigo conectar ao celular?
Consegui ouvir só pendrive, som ótimo.
My box doesn't have a bluetoo button, just a letter M instead.
Does that mean I can't connect to my cell phone?
I was able to listen to just a pendrive, great sound.
Olá bom dia!
Minha caixa não tem botão bluetoo, só uma letra M no lugar.
Quer dizer q não consigo conectar ao celular?
Consegui ouvir só pendrive, som ótimo.
Why does my speaker have an 'M' button instead of a Bluetooth button, and can I still connect it to my phone?
The official JBL Go 2 does not have an "M" (Mode) button or a USB port for a pendrive (thumb drive); it only features a Micro-USB port for charging and a 3.5mm auxiliary input. If your speaker has an "M" button and supports a pendrive, it is likely a different model or a third-party product rather than an authentic JBL Go 2.
However, on most speakers with an "M" button, that button is used to switch between different modes (Bluetooth, FM Radio, USB, or Aux). To connect to your phone, try the following:
If your device is an authentic JBL Go 2, the Bluetooth button is located on the top panel and is represented by the standard Bluetooth symbol (not a letter M).
Read the full Q&A page
Hello good day!
My JBL box doesn’t have a bluetoo button, just a letter M instead.
Does that mean I can’t connect to my cell phone?
I was able to listen to just a pendrive, great sound.
Olá bom dia!
Minha caixa JBL não tem botão bluetoo, só uma letra M no lugar.
Quer dizer q não consigo conectar ao celular?
Consegui ouvir só pendrive, som ótimo.
My JBL box doesn't have a bluetoo button, just a letter M instead.
Does that mean I can't connect to my cell phone?
I was able to listen to just a pendrive, great sound.
Olá bom dia!
Minha caixa JBL não tem botão bluetoo, só uma letra M no lugar.
Quer dizer q não consigo conectar ao celular?
Consegui ouvir só pendrive, som ótimo.
Why does my speaker have an 'M' button instead of a Bluetooth button, and can I still connect it to my phone?
Based on your description, it is likely that you have a different model or a non-authentic version of the speaker. The genuine JBL Go 2 does not have an "M" button, nor does it have a USB port for playing music from a pendrive (it only has a Micro-USB port for charging and a 3.5mm Aux input).
On speakers with an "M" (Mode) button, this button is typically used to switch between different audio sources, such as FM Radio, USB/Pendrive, and Bluetooth. To connect to your cell phone, try the following:
If these steps do not work, you may need to refer to the specific manual for that device, as its controls differ from the standard JBL Go 2 manual.
Read the full Q&A page
“It seems that I have some problem with JBL go2.
I got it brand new and it only works while connected to the charger.
There are only white color LEDs, no blue, no red colors.
As soon as I unplug it from the charger it shuts off.
Any solution for this?”
I am having this same problem. Even charging, after a few minutes ringing it turns off again.
How can I solve that?
“Parece que tengo algún problema con JBL go2.
Lo tengo nuevo y solo funciona mientras está conectado al cargador.
Solo hay LED de color blanco, sin azul, sin colores rojos.
Tan pronto como lo desconecto del cargador, se apaga.
¿Alguna solución para esto?”
Esto teniendo este mismo problema. Incluso cargando, despues de unos minutos sonando vuelve a apagarse.
Cómo puedo solucionarlo?
I got it brand new and it only works while connected to the charger.
There are only white color LEDs, no blue, no red colors.
As soon as I unplug it from the charger it shuts off.
Any solution for this?"
I am having this same problem. Even charging, after a few minutes ringing it turns off again.
How can I solve that?
"Parece que tengo algún problema con JBL go2.
Lo tengo nuevo y solo funciona mientras está conectado al cargador.
Solo hay LED de color blanco, sin azul, sin colores rojos.
Tan pronto como lo desconecto del cargador, se apaga.
¿Alguna solución para esto?"
Esto teniendo este mismo problema. Incluso cargando, despues de unos minutos sonando vuelve a apagarse.
Cómo puedo solucionarlo?
Why does my JBL Go 2 only work when plugged into a charger and shut off immediately when unplugged?
Based on your description, your JBL Go 2 is likely experiencing a battery failure or a charging circuit issue. Here are some steps to troubleshoot and potential causes:
Note: While the manual states the JBL Go 2 can be used while charging, it should be able to operate for up to 5 hours on battery power alone after a full 2.5-hour charge.
Read the full Q&A page
昨日電池が切れて1日放置したら 充電もされません 電源も入りません
Why is my JBL Go 2 not charging or turning on after the battery died and was left for a day?
If your JBL Go 2 is not responding after the battery was completely drained, please try the following troubleshooting steps:
Note: If the red light stays on but the device never turns on or charges, the battery may have entered a deep discharge state or the internal PCM circuit may have tripped, which might require professional service.
Read the full Q&A page
My JBL GO2 is not connecting the bluetooth with my Android, how should I reconnect?
How do I reconnect my JBL Go2 to my Android device via Bluetooth?
To reconnect your JBL Go2 to your Android device, follow these steps to initiate pairing mode:
If the device was previously paired but won't connect, try "Forgetting" or "Unpairing" the JBL GO 2 from your Android Bluetooth settings first, then repeat the steps above. Ensure no other devices are currently connected to the speaker, as it can only connect to one source at a time.
Read the full Q&A page