ID115 Smart Bracelet User Manual & App

The time on the ID115 smart bracelet is set automatically when you synchronize the device with the Veryfit 2.0 app on your smartphone or tablet. There is no manual time setting on the bracelet itself.

To set the proper time, follow these steps:

• Ensure Bluetooth is enabled on your mobile device.
• Open the Veryfit 2.0 app.
• Ensure the bracelet is paired (bound) to the app. If it is not, go to the device settings in the app to search for and bind the bracelet.
• Once connected, the app will automatically sync the date and time from your phone to the bracelet.
• If the time does not update immediately, you can manually trigger a sync by clicking on the app screen and pulling down.

Note: The bracelet must stay within the 10-meter Bluetooth range of your phone to maintain the connection and sync data successfully.

If your ID115 Smart Bracelet screen is blank, it is most likely due to a depleted battery or an improper charging connection. Please follow these troubleshooting steps:

• Check the Charge: The device may be completely out of power. It takes approximately 3 to 4 hours to charge from 0% to 100% using a standard USB port, and up to 6-8 hours if plugged into a laptop or PC.
• Verify Charging Orientation: The ID115 uses a USB charging style where you must remove the device from the band and plug the body directly into a USB port. Ensure the metal charging strips on the device are making direct contact with the pins inside the USB port. If it doesn't start charging, try flipping the device over and re-inserting it.
• Check for Water Damage: Note that this device has an IP-X4 rating, meaning it is only water-resistant for daily life (splashes). If the device was submerged during swimming or a shower, the internal components may be damaged.
• App Connection: Check your Veryfit 2.0 app to see if the device is still "Connected." If the app shows the device is connected and syncing data but the screen remains black, the display hardware may be faulty.

If the screen does not turn on after a full 8-hour charge in a known working USB port, the battery or display may have reached the end of its service life.

{ "is_valid_question": true, "normalized_question_en": "How can I fix a blank screen on my ID115 Smart Bracelet?", "contextual_details_en": "Troubleshooting a blank or unresponsive screen on an ID115 Smart Bracelet.", "answer_en": "

If your ID115 Smart Bracelet screen is blank, it is most likely due to a depleted battery or an improper charging connection. Please follow these troubleshooting steps:

• Check the Charge: The device may be completely out of power. It takes approximately 3 to 4 hours to charge from 0% to 100% using a standard USB port, and up to 6-8 hours if plugged into a laptop or PC.
• Verify Charging Orientation: The ID115 uses a USB charging style where you must remove the device from the band and plug the body directly into a USB port. Ensure the metal charging strips on the device are making direct contact with the pins inside the USB port. If it doesn't start charging, try flipping the device over and re-inserting it.
• Check for Water Damage: Note that this device has an IP-X4 rating, meaning it is only water-resistant for daily life (splashes). If the device was submerged during swimming or a shower, the internal components may be damaged.
• App Connection: Check your Veryfit 2.0 app to see if the device is still Connected. If the app shows the device is connected and syncing data but the screen remains black, the display hardware may be faulty.

If the screen does not turn on after a full 8-hour charge in a known working USB port, the battery or display may have reached the end of its service life.

" }

If you are unable to scan the barcode to register or download the app for your ID115 Smart Bracelet, you can bypass the scanner by following these steps:

• Download the App Manually: Search for "Veryfit 2.0" (or "VeryFitPro" depending on your specific version) directly in the Google Play Store for Android or the Apple App Store for iOS.
• Check Compatibility: Ensure your phone is running Android 4.5 or above, or iOS 8.0 or above. Note that the app may not function correctly on screens smaller than 4.5 inches or on Windows mobile devices.
• Pairing without a Barcode: You do not typically need a barcode to register the watch itself. Once the app is installed:
  1. Turn on your phone's Bluetooth.
  2. Open the Veryfit 2.0 app.
  3. Go to the device binding section. The app will search for nearby devices.
  4. Select the ID115 from the list to bind it.
• Charging: If the device is not appearing, ensure it is fully charged by removing the strap and plugging the USB end into a computer port for 3-4 hours.

If the official webpage remains blank, it may be down; using the official app store for your device is the most reliable alternative.

To synchronize your ID115 smart bracelet with a new phone, you must first ensure it is disconnected from your previous device. Bluetooth devices typically only allow one active "binding" at a time. Please follow these steps:

• Unbind from the old phone: Open the Veryfit 2.0 app on your old phone and remove or "unbind" the device. You should also go to the Bluetooth settings of the old phone and select "Forget this device."
• Check Compatibility: Ensure your new phone meets the requirements: Android 4.5+ or iOS 8.0+ with a screen size of at least 4.5 inches.
• Enable Bluetooth: Turn on Bluetooth on your new phone and keep the bracelet within 10 meters (30 feet).
• Pairing via App: Open the Veryfit 2.0 app on the new phone. Do not try to pair the bracelet directly through the phone's Bluetooth menu; instead, use the app's "Binding Device" or "Choose a Device" section to search for and connect to the bracelet.
• Syncing: Once connected, pull down on the app's main screen to trigger a manual data synchronization.

If the device still won't connect, ensure the bracelet is fully charged (3-4 hours) as low battery can interfere with the Bluetooth signal.

To adjust the stride length for your ID115 smart bracelet, you must use the Veryfit 2.0 app on your smartphone, as this setting cannot be changed directly on the bracelet itself. Follow these steps:

• Open the Veryfit 2.0 app.
• Go to the User or Profile section (usually located at the bottom of the screen).
• Look for Personal Info or User Info.
• Within your personal profile settings, you should find a field for Stride or Step Length.
• Enter your measured stride length and save the settings.
• Sync the app with your bracelet by pulling down on the main screen to ensure the new data is applied for distance calculations.

Note: If you cannot find a specific stride length field, ensure your height is set correctly in the app, as many fitness trackers calculate an estimated stride length automatically based on the user's height.

Intermittent connection issues with the ID115 smartband are often related to distance or app settings. Please try the following troubleshooting steps:

• Check the Distance: Ensure your smartband and phone are within the 10-meter (33 feet) Bluetooth range. If you move further away, the device will disconnect automatically.
• Keep Bluetooth Active: Ensure Bluetooth is turned on at all times on your smartphone.
• App Compatibility: Confirm you are using the Veryfit 2.0 app. Note that the app may not function correctly if your phone screen size is less than 4.5 inches or if you are using a Windows Mobile device.
• Manual Sync: If the data does not sync automatically, open the Veryfit 2.0 app and swipe down on the main screen to trigger a manual sync. You should see a "connecting" icon.
• Battery Level: Ensure the bracelet is sufficiently charged, as low battery can cause the Bluetooth signal to weaken. A full charge takes about 3-4 hours via a standard USB port.
• Reset Connection: If the problem persists, try unbinding the device in the app settings, restarting your phone's Bluetooth, and then re-binding the device through the app's "Choose a Device" menu.

To reset the settings or clear the step counter on your ID115 smart bracelet, you generally need to use the Veryfit 2.0 app on your smartphone. Please try the following methods:

• Automatic Reset: The step counter is designed to reset to zero automatically every night at midnight.
• Unbinding/Rebinding: To perform a factory-style reset of the settings, open the Veryfit 2.0 app, go to the User or Device section, and select Unbind. Once disconnected, you can pair (bind) the device again to refresh the settings.
• App Data Clear: If you wish to clear the history of your steps, you can clear the cache or data within the app settings on your phone, though this will remove all previous activity records.

Note: The physical device itself does not have a dedicated reset button; most management is handled through the Bluetooth connection with the app.