STUDER vt80 variotrack Instructions

STUDER-logo

STUDER vt80 variotrack

STUDER-vt80-variotrack-product

Overview

The VarioTrack (VT) is a solar MPPT charge controller that recharges a connected battery from photovoltaic (PV) panels in an optimum way. It is designed and manufactured by Studer in Switzerland and is intended for use as part of a battery-based energy management system.

Specifications

Protection / Class IP 54, Protection Class I
PV Max Voltage 150 Voc (75 Voc @ 12Vdc)
PV Max Current VT 40: 35A
VT 65: 60A
VT 80: 75A
Battery Nominal Voltage 12/24/48 Vdc
Battery Charge Current VT 40: 40A
VT 65: 65A
VT 80: 80A
Battery Voltage Range (Min–Max) 17–68 Vdc
PV side cable / terminal torque VT 40: 10mm² cable, M5, 5Nm
VT 65 / VT 80: 25mm² cable, M6, 5Nm
Battery side cable / terminal torque VT 40: 16mm² cable, M5, 5Nm
VT 65 / VT 80: 25mm² cable, M6, 5Nm
Earthing (grounding) conductor 16mm² cable
Protection device (PV side) – max solar current VT 40: 35A
VT 65: 60A
VT 80: 75A
PV overvoltage protection SPD (150Vdc)
Protection device (Battery side) – max current VT 40: 50A
VT 65: 80A
VT 80: 100A
PV input range note INPUT 0–150Voc (0–75 Voc @ 12Vdc)
Series / parallel wiring note In series, up to 150Voc (75 Voc @ 12Vdc). In parallel, see recommended power table below (as provided):
12V: VT40 625W / VT65 1000W / VT80 1250W
24V: VT40 1250W / VT65 2000W / VT80 2500W
48V: VT40 2500W / VT65 4000W / VT80 5000W

Quick setup

  1. Plan installation so the device is installed by qualified personnel and in accordance with local standards and regulations.
  2. Mount the VT in an appropriate location; batteries should only be installed by qualified personnel.
  3. Connect PV: use the specified PV cable sizes and terminal torque (VT 40: 10mm², M5, 5Nm; VT 65/VT 80: 25mm², M6, 5Nm) and include a PV side protection device sized to the max solar current.
  4. Connect battery: use the specified battery cable sizes and terminal torque (VT 40: 16mm², M5, 5Nm; VT 65/VT 80: 25mm², M6, 5Nm) and include a battery side protection device sized to the max current.
  5. Connect earthing (grounding) using a 16mm² cable and ensure the solar generator is class II isolated.
  6. Make communication connections as required (RJ45 for RCC 02/03 / multi-units; RJ11 for BTS 01 / ARM 02).
  7. Apply system power and configure the VarioTrack units using the provided DIP switch configuration and RCC 02/03 configuration interface (when applicable).
  8. During operation, refer to the display system indicators (status and blinking behavior vary by VT model and current range).

Introduction
Congratulations! You are about to install and use a high-end piece of equipment that will play a central role in the energy management of your battery-based system. The Variotrack (VT) is a solar MPPT charge controller. When connected to a battery and photovoltaic panels, the VT will optimally recharge the battery. This VT has been designed, manufactured, assembled, and tested in our factory in Switzerland.

General Information

Exclusion of liability
Studer disclaims all responsibility and liability for damage, costs or losses resulting from an installation that does not comply with the instructions, a faulty operation or inadequate maintenance. The use of studer equipment is in any case under the responsibility of the customer. Read carefully the safety and operation instructions / Installation must be entrusted to qualified personnel / Check the user manual online / Need helpSTUDER-vt80-variotrack-fig- (1)Compatible with

STUDER-vt80-variotrack-fig- (2) Mounting and installation

Storage and contentSTUDER-vt80-variotrack-fig- (3) Mounting place
The batteries should only be installed by qualified personnel.STUDER-vt80-variotrack-fig- (4) Fixing and dimensionsSTUDER-vt80-variotrack-fig- (5) WiringSTUDER-vt80-variotrack-fig- (6) The device must be installed in accordance with local standards and regulations in force

Multi units and power upSTUDER-vt80-variotrack-fig- (7)

Display

Display system

STUDER-vt80-variotrack-fig- (8)Configuring the variotracks

DIP switchesSTUDER-vt80-variotrack-fig- (9) Vt 80 specificities
Assembling the cooling fanSTUDER-vt80-variotrack-fig- (10) Technical dataSTUDER-vt80-variotrack-fig- (11)Maintenance and recycling
Except for the periodic check of the connections (tightening, general condition), the variotrack does not require any particular maintenance. To dispose of this product, please use the service for the collection of electrical waste and observe all obligations in force in the place of purchase.

  1. Serial Number:
  2. Installed by :
  3. Date :
  4. Signature :

All rights reserved Studer Innotec SA – V1.2.1

Troubleshooting

  • General: If installation, operation, or maintenance does not comply with the instructions, Studer disclaims responsibility for damage, costs, or losses. Verify installation matches the manual and local regulations.
  • Connection check: Apart from periodic checks of the connections (tightening, general condition), no particular maintenance is required. If performance issues occur, first inspect and re-tighten connections as appropriate.
  • Installation failures: Ensure the device is installed by qualified personnel and that PV/battery connections use the specified cable sizes, protection devices, and overvoltage protection (SPD 150Vdc).
  • Status indication: Use the VT display/blinking status indicators (on status and blinking status) to determine whether current ranges correspond to the expected model-specific ranges shown in the manual.
  • Need help: Contact Studer specialists via the provided support number or support website if issues persist.

Documents / Resources

PDF thumbnailvt80 variotrack (vt)
Instructions · Studer Innotec, vt 40, vt 65, vt 80, V1.2.1, variotrack vt, solar charge controller, MPPT

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.