Vanemar M1-E Vanemar Motion Sensor User’s Guide User Manual

Vanemar M1-E Vanemar Motion Sensor

Technical Specifications

• Model M1-E
• Working Voltage DC3V (1 x CR2 Battery)
• Detecting Angle 110°
• Illuminance Detection Range 0~1200 Lux
• Maximum Detecting Distance Up to 7 m at 25°C – 23 ft at 77°F (distance varies with temperature)
• Wireless Networking Distance ≤70 m (in the open area) / ≤230 ft
• Working Temperature Humidity – 10°C ~ +55°C/ 14°F~ 131°F ≤95% RH
• Dimensions 42 × 43 mm / 1.65 × 1.69 in
• FCC ID 2AK7XM1-E

Meet Vanemar Motion Sensor
Designed to enhance awareness on your boat, the Vanemar Motion Sensor signals the presence of movement within its field of view.

• Signals when movement is detected.
• May warn when the device’s battery is low.
• May warn of potential tampering with the sensor.

Overview

In the box

Safety And Preparation

• Securing the Boat
  Before beginning the installation, make sure the boat is stationary and securely moored to provide a stable environment.
• Work Environment
  Ensure the area is well-ventilated and free of clutter to facilitate a safe installation process.

INSTALLATION

1. Pairing
   Ensure the battery insulation pull tab is removed before pairing. Open the Vane mar App. Tap ‘+’ or ‘Add device’ button in the ‘Devices’ menu and follow the on-screen instructions.
2. Fixing in Place
   Pick a flat indoor spot for installation where the motion sensor can see the area you want to monitor, making sure nothing blocks its view. Please refer to the “Installation Precautions” and “Detecting Area” sections for detailed guidance.

Please ensure the surface is clean before applying the adhesive. Press firmly to ensure it is securely fixed.

Option 1: Using the mounting bracket, the sensor can be installed on walls or ceilings. This allows easier adjustment of the sensor’s angle and position.

• Peel one side of the double-sided adhesive tape and attach it to the mounting bracket.
• Peel the other side and mount the bracket to the desired position on the wall or ceiling.
• Attach the sensor body to the mounting bracket.
• When attaching, ensure that the  6.” (for wall mounting) (for ceiling mounting) icon on the bracket aligns with the icon on the sensor body.

Option 2: The sensor body can be attached directly to the wall using double-sided adhesive tape.

• Peel one side of the double-sided adhesive tape and attach it to the sensor body as shown.
• Peel the other side and mount the sensor to the desired position on the wall.
• Ensure the icon on the bottom cover is facing upward during installation.

WARNING: The disassembly hole is located at the bottom of the device. Leave enough space below the sensor to allow easy removal.

Detecting Area 

Installation Precautions
Install the sensor indoors on a stable surface, considering its field of view to ensure a clear view of potential intruder paths. To prevent false alarms, position the sensor in a location where animals and moving objects, like fans, won’t enter its field of view, and avoid areas where temperature changes from sources such as air conditioners and heaters, as well as direct sunlight, could be mistakenly interpreted as movement.

Indicators 

• Red flash once Motion Detected
• Rapidly flashing green Searching for Gateway (Pairing Mode)
• Solid green for 3 seconds, then off Unpaired
• Solid green for 3 seconds, then off Paired Successfully

Detection Behavior
When powered on, the sensor warms up for 30 seconds, indicated by a flashing red LED, and then starts detecting motion. Once motion is detected, the sensor enters sleep mode, not detecting any movement for 60 seconds, then resumes detection.

Using the Networking Button
To put your device into pairing mode, press and hold the networking button with the included reset tool until the green LED starts flashing rapidly. This indicates that the device is ready to pair. Once successfully paired, the LED will remain solid green for 3 seconds before turning off. To unpair your device, press and hold the networking button with the reset tool until the green LED flashes slowly, which should take about 5 seconds. This indicates that the device has been successfully disconnected.

Changing the Battery
Press the disassembly hole by the pin key, remove the bottom cover from the sensor body. The device needs a single CR2 battery. Make sure to match the plus{+) and minus(-) signs on the battery with those in the battery space. Keep an eye on the Vane mar App for low battery alerts and change the battery when you receive the alert to ensure the device functions properly.