LEKATO ME-01 Multi Effects Processor Owner’s Manual

LEKATO logoME-01 Multi Effects Processor
Owner’s ManualLEKATO ME 01 Multi Effects Processor

Preface

ME-01 is a portable and multifunctional Guitar/Bass effector. ME-01 has 80 editable Presets, the users also can customize effectors chain and save. It has built-in battery, it can last up to 10 hours on a full charge. ME-01 has 6 effects Modules, it provides the Noise Gate, Boost, Compressor, 20 Preamp, 3-band EQ, 7 Modulations, 5 Delays, 6 Reverbs, 20 IR CAB slots and so on.
Press the HOME button on the Main Display Screen to enter the Module Operation Screen, then use the EDIT Knob to customize the position of the effects Module. At this time, you can also select any Module by pressing the Right-Footswitch and then open/close this module with the Left-Footswitch, which is convenient for the user to control the Module on/off with the foot during the performance(Stomp Mode). When you click the MOD/DLY Button, the MOD/DLY Module opens on the screen, you can tap the Right-Footswitch to adjust the effect speed of the MOD/DLY Module.
You can download the computer software or mobile APP from our official channels, use it to edit presets, swap presets, share presets, import/export presets, and import the IR files, import the AMP module timbre data(The file format is AM2, AM3, AMx,etc), besides you can restore the factory Settings or firmware upgrade on the computer. It support BT wireless music, earphone monitoring function, and computer sound card, etc. ME-01 can be used as an audio interface with a cellphone, use a OTG converter (separately buying) and accessory USB cable to connect the cellphone, then enter any video/audio recording APP for direct recording. It integrates a variety of function, it is easy-carry and it has excellent sound! It could be a good partner of your music instruments.

Attentions

The power supply:
It is equipped with built-in battery for power supply, which can last for 10 hours after full charge. It can charge with the 5V adapter or the power bank. When the battery run low, you can use the 5V 2A adapter, you need 5 hours to fully charge the battery. When the battery run low, don’t use it for a long time to avoid unstable working performance, please charge it in time.
The connection:
Be sure to turn off the power of related equipment before connecting or disconnecting the device.
The electrical interference:
The electromagnetic wave of radio, television and other equipment may cause interference to the equipment, so please try to stay away from radio, television and other equipment.
The location:
To avoid deformation, discoloration, or other serious damage, do not expose this unit to the following conditions:
a. Heat sources
b. Magnetic fields
c. Sunlight
d. High temperature or moist district
e. Excessively dusty or dirty locations
f. Strong vibrations or shocks

Effectors chain diagram

(The order of the 6 effects Modules can be customized.)LEKATO ME 01 Multi Effects Processor - fig
Rear panel

LEKATO ME 01 Multi Effects Processor - fig1

  1. Power switch.
  2. IN: 1/4″ MONO audio input jack.
  3. Charging indicator: When the battery is normally using, the indicator will go off; During charging, the indicator will stay red, then it will change to a different color after fully charging.
  4. USB jack: Use to charge the battery/The ME-01 can be sound card of computer/Computer software can be connected for interactive data transmission/OTG recording/support MIDI Pedal.
    Tips: ME-01 can be used as an audio interface with a cellphone, use a OTG converter (separately buying) and accessory USB cable to connect the cellphone, then enter any video/audio recording APP for direct recording or playback music.
  5. OUT: 1/4″ MONO audio output jack.
  6. Earphone output.

Front panel

  1. LEKATO ME 01 Multi Effects Processor - fig2Master, Control the volume. (Note: The BT volume and USB input volume are not controlled by this knob.)
  2. EDIT knob (Rotary encoder with button), Rotate it to select items or adjust parameters, Click it to enter, exit, or confirm the items, Press and hold for 1 second to display the “Save to” screen, Press and hold for 2 second to display the “Swap to” screen.LEKATO ME 01 Multi Effects Processor - icon When on the “Save to” or “Swap to” screen, if you click the HOME button, you can exit and return to “Main Display Screen”.
  3. IN jack input volume real-time display bar.
  4. Wireless BT pattern, When the pattern is off, it indicates that BT is not enabled. A white pattern indicates that BT has started but is not connected. The blue pattern indicates that BT is successfully connected.
  5.  Battery status pattern.
  6. This diagram shows the order and the on/off state of the 6 effect Modules. If the pattern is off, the effect is not enabled. If the pattern is on, the effect is started. The state of the pattern corresponds to the state of the 6 buttons down on the right. If all 6 patterns are Off, the ME-01 is in Bypass state.
  7. Preset number, When this number is selected using the EDIT knob, rotate it to quickly switch Presets. ME-01 includes 80 Presets, with the first 40 (P01~P40) containing default factory effects, thereinto the P36-P40 were designed for bass. When you need the factory reset, you can separately reset these 40 Presets to the default values. If you want reset all the 80 Presets, it is also feasible.
    Note: Enter the mobile APP or computer software interface to perform this operation.
  8. The volume of current Preset.
  9. HOME illuminated Button / BT switch Button(with BT status light), click the HOME button to display the Main Display Screen on the screen, then press the HOME button again to enter the Module Operation Screen. Besides, you can hold this button to open/close the BT. When the button light off, the BT had been turned off; when the button light flashing, it means BT is turning on, but not in connection; when the button light keep on, it means BT has been connected.
    “Main Display Screen” is the home page displayed right after the power is turned on. You can directly see the key information and settings of the current Preset, you can also know about battery conditions and other information and so on.LEKATO ME 01 Multi Effects Processor - icon1Module Operation Screen: In this screen, you can operate the connection order of 6 modules by using EDIT knob, you can also open/close a module freely by using two Footswitches (Stomp Mode).LEKATO ME 01 Multi Effects Processor - icon2
  10. FX Module illuminated Button, Click to enter the Edit Settings Menu of Module, then click again to turn on/off Module. At any time, you can hold the button to quickly turn on/off Module. If this Button is lighting on, it means the Module is turned on. If the light goes off, the Module is turned off. When the Edit Settings Menu is displayed on the screen, you can use the EDIT encoder to adjust any of the effects and parameters on the screen. At this time, you can also use the Left Footswitch to turn the current Module on/off.
    Tips: The buttons of the 6 effects Modules all support the above functions.
  11. AMP Module illuminated Button.
  12. Modulation Module illuminated Button, When the Screen displays the MOD’s Edit Settings Menu, you use the Right Foot switch, you can also Tap to obtain the Speed parameter of the effect. At this time, if the Module has been turned on, the button light will also blink based on the Speed parameter.
  13. Delay Module illuminated Button, When the Screen displays the DLY’s Edit Settings Menu, you use the Right Foot switch, you can also Tap to obtain the Time parameter of the effect. At this time, if the Module has been turned on, the button light  will also blink based on the Time parameter. When the Screen displays the DLY’s Edit Settings Menu and the DLY had been turned on, you can hold the Right-footswitch to start the Hold function, after a long step of 1.5 seconds the machine will read the Delay wet sound at this moment. If you don’t release the foot, you’ll keep this Hold sound. If you release the foot, you can immediately cancel the Hold sound (Freeze function).
  14. REV Module illuminated Button.
  15. IR CAB Module illuminated Button.
  16. Left Footswitch, it use to turn down the Presets when in Main Display Screen. In some other interfaces, it can be used for on/off Modules. You can press the left and right Footswitches at the same time to enter Tuning Mode, and then click either Footswitch to exit tuning.
  17. Right Footswitch, it use to turn up the Presets when in Main Display Screen. When in the Module Operation Screens, it can be used to select Modules. When in the MOD/DLY Module screen, you can tap the Right-Footswitch to adjust the effect speed of the MOD/DLY Module. When in the DLY Module Screen and the DLY is turned on, you can hold the Right-footswitch to enable the Hold function (freezing the wet sound to get the unlinited voice).
    Note: On some interfaces, the Right-Footswitch does not work.
    Tips: The tuning interface is shown in the picture. There are two items to choose from in this interface, the “refer to” item is to select the standard A’s frequency 430-450Hz, the “Mode” item is to select the voice output status Bypass or Mute.LEKATO ME 01 Multi Effects Processor - icon3

Effectors module

I: FX Module (FX module can select Noise Gate or NG+Boost or NG+Compress, three collocation ways, you can use 6+1 effect at the same time.)

  1. Noise Gate
    Gate parameter, Adjust the intensity of Al Noise Gate, When set to 0, the effect is turned off.
  2. Boost (Noise Gate can be added)
    Gate parameter, Adjust the intensity of Al Noise Gate, When set to 0, the Noise Gate is turned off.
    Gain parameter, Adjust the gain of the Boost.
  3. Compress (Noise Gate can be added)
    Gate parameter, Adjust the intensity of Al Noise Gate, When set to 0, the Noise Gate is turned off.
    Sustain parameter, Adjust the compression amount.
    Attack parameter, The starting time of the compressor after the signal exceeds the threshold, the larger the value, the slower the compression starting time, and the more prominent the auditory sound-head; The smaller the value, the faster the startup time.
    Level parameter, Use this parameter to adjust the output volume of this Module again.
    II: AMP Module (1-15 is guitar preamp, 16-20 for bass preamp)
    Gain, Adjust the gain of AMP.
    Level, Adjust the level of AMP.
    Bass, Adjust the bass of AMP.
    Mid, Adjust the middle of AMP.
    Treble, Adjust the treble of AMP.
    III: Modulation Module (Support TAP function)
    1. Chorus
    Speed: Adjust the effect speed.
    Depth: Adjust the effect depth.
    Mix: Adjust the dry and wet ratio.
    2. Phaser
    Speed: Adjust the effect speed.
    MitCut: The larger the value, the greater the midfrequency reduction of the effect, this parameter is mainly designed for distortion timbre.
    Resonance: Resonance intensity adjustment of phase effect.
    Feedback: Adjust the feedback amount of Phaser.
    3. Tremolo, it is basically a change of the signal level controlled by an Low-frequency Oscillator.
    Speed: Adjust the effect speed.
    Depth: Adjust the effect depth.
    Level parameter, Use this parameter to adjust the output volume of this Module again.
  4. Flanger, it is use the same principle as Chorus, but it uses a shorter delay time and adds regeneration(or repeats) to the modulating delay. This results in an exaggerated up and down sweeping motion to the effect.
    Speed: Adjust the effect speed.
    Depth: Adjust the effect depth.
    Feedback: Adjust the amount of feedback for the sweep effect in wet sound.
    Mix: Adjust the dry and wet ratio.
  5. Vibrato, The vibrato effect modulates the pitch of the incoming signal. The result is similar to the Tremolo technique used by vocalists. In contrast to a Chorus or Flanger effect, no direct signal is combined with the pitch-modulated signal.
    Speed: Adjust the effect speed.
    Depth: Adjust the effect depth.
  6. Univibe, a unique timbre, a combination of chorus and phaser.
    Speed: Adjust the effect speed.
    Depth: Adjust the effect depth.
    Mix: Adjust the dry and wet ratio.
  7. Autofilter, filter works regularly by setting the frequency, both guitar and bass can be used.
    Speed: Adjust the speed of Autofilter.
    Min: Minimum frequency of the filter sweep frequency, when the value is turned down, the middle and low frequency parts of the wet sound are more prominent.
    Max: Maximum frequency of the filter sweep frequency, when the value is turned up, the middle and high frequency parts of the wet sound are more prominent.
    Mix: Adjust the dry and wet ratio.
    Feedback: Adjust the feedback amount of Autofilter.
    IV: Delay Module(Support TAP and Freeze function)
    1. Analog, it is the delay effect of the signal of the analog tube, and the timbre has the characteristics of retro and warm.
    Time, adjust the feedback speed of echo repeats, 600-60bpm.
    Feedback, the feedback times of echo repeats.
    Mix, Adjust the dry and wet ratio.
    Phaser, the Phaser effect is increased in the Delay wet sound. This parameter can adjust the amount of Phaser used.
    Pitch: We add a little detuning effect to the delay wet sound, this parameter adjusting the pitch of the detuning effect, which is a slightly shifted sound, a retro and charming sound.
    2. Duck Delay, When we process the delayed wet sound, we add the Noise Gate to the part before the wet sound. Thus, the front part of the wet sound is suppressed to achieve a front evasive effect, and the sound is gradually increased, the dynamics of the delay are more ‘felt’ than ‘heard’.
    Time, adjust the feedback speed of echo repeats, 600-60bpm.
    Feedback, the feedback times of echo repeats.
    Mix, Adjust the dry and wet ratio.
    Unpack, After this parameter is turned up, the sudden rise in the volume of the wet rear part can be unpacked, so as to achieve a smoother delay dynamic.
    Speed, the Chorus effect is increased in the Delay wet sound. This parameter can adjust the speed of Chorus used.
    Depth, this parameter adjusts the depth of the Chorus.
    3. dTape, Tape delay, it replicates the unique delay style of tape machine, you can not only get the warmth and silky of professional grade tape machine, but also simulate the sound effects of tape in real situations such as CRINKLE, BIAS, and so on.
    Time, adjust the feedback speed of echo repeats, 600-60bpm.
    Feedback, the feedback times of echo repeats.
    Mix, Adjust the dry and wet ratio.
    Grit, the GRIT takes on the function of TAPE BIAS. This parameter adjusts tape machine bias, from under biased to over-biased, it sounds like an overdrive of wet sounds. Bias sets the dynamic range and headroom of the wet signal.
    Speed, the SPEED takes on the function of TAPE CRINKLE. This parameter adjusts the amount and severity of tape irregularities, including friction, creases, splices and contaminants. Tape Crinkle characteristics track accordingly to tape speed. Set to minimum for a fresh, clean tape. Set to maximum for a tape that has been mangled and chewed for years.
    Depth, This parameter control varies the amount of mechanically related tape speed fluctuations. This also results in natural tape machine style modulation, it’s like a chorus. Parameter minimum for a more tuned, cleaned and serviced tape machine. Parameter maximum to hear the sound of a tape machine in need of service. In between the extreme settings, a natural tape modulation is achieved.
    4. Dual Delay, two independent delay echoes, the time-lag of the first echo and the second echo achieves a very interesting delay rhythm effect.
    Time, adjust the feedback speed of echo repeats, 1200-120bpm.
    Feedback, the feedback times of echo repeats.
    Mix, Adjust the dry and wet ratio.
    Time-Mode, Adjust the time-lag between the two echoes, the minimum is the equivalent of no time-lag, and the greater the number, the greater the time-lag.
    Speed, the Chorus effect is increased in the Delay wet sound. This parameter can adjust the speed of Chorus used.
    Depth, this parameter adjusts the depth of the Chorus.
    5. Lofi Delay, a special, retro and destructive delay effect, the wet sound reflects the filter, the vinyl record, the noise lo-fi and many other senses.
    Time, adjust the feedback speed of echo repeats, 600-60bpm.
    Feedback, the feedback times of echo repeats.
    Mix, Adjust the dry and wet ratio.
    Grit, When the parameter is turned up, it sounds like a overdrive wet sound.
    Speed, the Chorus effect is increased in the Delay wet sound. This parameter can adjust the speed of Chorus used.
    Depth, this parameter adjusts the depth of the Chorus.

V: Reverb Module

  1. Room reverb, it simulates a relatively small, simple-structured room sound where many reflections are absorbed by soft material in the room, and sound is reflected by walls.
    Decay, Adjust the duration of echo.
    Mix, Adjust the ratio of wet and dry.
    HPass, HIGH pass, only used to regulate wet sound.
    LPass, Low pass, only used to regulate wet sound
    Depth, the pitch of wet sound produces a small cyclical rise and fall, you will hear vintage and charming background sound.
  2. Hall reverb, it gives a wide, slightly scattering feeling, it simulates a grand ambient sound.
    Decay, Adjust the duration of echo.
    Mix, Adjust the ratio of wet and dry.
    HPass, HIGH pass, only used to regulate wet sound.
    LPass, Low pass, only used to regulate wet sound
    Depth, the pitch of wet sound produces a small cyclical rise and fall, you will hear vintage and charming background sound.
  3. SWELL reverb, the Swell machine brings in the reverb gradually behind the dry signal for subtle evolving textures, like having a volume pedal on the wet sound.
    Decay, Adjust the duration of echo.
    Mix, If the dry sound is removed, and set the RiseT parameter to 0, it can mimic the sound of string instruments such as the violin.
    HPass, HIGH pass, only used to regulate wet sound.
    LPass, Low pass, only used to regulate wet sound
    RiseTime, it adjusts the rise time of the swelled signal, I suggest you choose shorter times for single-line soloing or longer times for ambient chord work.
  4. Spring reverb, it is a common type of reverberation. The sound signal is transmitted to the spring tank, and the pickup picks up the resonant sound of the spring tank, to mimics the reverberation effect produced in space.
    Decay, Adjust the duration of echo.
    Mix, Adjust the ratio of wet and dry.
    HPass, HIGH pass, only used to regulate wet sound.
    LPass, Low pass, only used to regulate wet sound
    Combs, control the number of springs.
  5. Shimmer reverb, there is a pitch-shift sound in the wet sound. Adjust the pitch of the pitch-shift sound, you can get the dissonant interval, create a scary background sound. You also can get the harmonic interval, it’s a wonderful sound, a resplendent and unearthly ambience. The Amount parameter allow for a range of shimmer effects from laid-back and subtle to full-blown majestic splendor.
    Decay, Adjust the duration of echo.
    Mix, Adjust the ratio of wet and dry.
    Tone, Adjust the brightness of the reverb wet sound.
    Pitch, Adjust the pitch of the pitch-shift sound, the minimum value is the same as the original sound, the maximum value is two octaves above the original sound.
    Amount, adjust the amount of pitch-shift sound.
  6. Cloud reverb, is a gorgeous large ambient reverberation, it sounds like the music come from all sides of the cloud. Cloud reverb can take any modest guitar or synth sound and turn it into a gorgeous ensemble.
    Decay, Adjust the duration of echo.
    Mix, Adjust the ratio of wet and dry.
    HPass, HIGH pass, only used to regulate wet sound.
    LPass, Low pass, only used to regulate wet sound
    Diffusion, softens the early reflections to create a more diffused reverb. As Diffusion is increased, the reverb is smoothed and softened, the delay and reverberation mix together more naturally.

VI: IR CAB Module (1-15 is guitar CAB simulator, 16-20 is bass CAB simulator)

  • Level, Adjust the level of CAB.
  • Low cut, Adjust the low cut point, optionally 20-300 Hz. If you choose 300 Hz, it means that low frequencies below 300 Hz are suppressed.
  • High cut, Adjust the high cut point, optionally 18000-5000 Hz. If you choose 5k Hz, it means that high frequencies above 5000 Hz are suppressed.

Technical parameters

Input Standard 1/4″ jack MONO/TS
Output Standard 1/4″ jack MONO/TS, 1/8″ Stereo jack
Sample rate 44.1 KHz/24bit
Size 118(L)x115(W)x41(H)mm
Weight 425q
Power supply&USB data transmit Type-C, 5W300mA
Battery capacity 2000mah
Battery Model/Type 103450
Battery Nominal Voltage 3.7V
Battery life 10+ hours
Charging current limit About 408 mA
Dynamic Range 105dB
Total effects 60+
Effects Slots/Effects Modules Total of 6+1 simultaneous effects slots, it can customized the order
Presets amount 40+40
USB AUDIO (OTG) 44.1 K/24Bit, support Loopback ON/OFF
USB MIDI Support
BT music Support
Software support WINDOWS,MAC,IOS,Android
IR processing 44.1 K/24Bit Mono WAV files, 1024 sampling points
Power supply Built-in battery or USB 5V
AMP modeler Total& 20 (1-15 is electric guitar preamp, 16-20 for bass preamp)
IR slots Totally 20 (1-15 is electric guitar CAB, 16-20 for bass CAB)
Working current About 200 mA
Attachment USB cableX1

Other

  • Software Download
    For mobile devices (Android/iOS) and computers, please download the M-EFCS software from the following website: https://lekatotech.com/
  • Tips: Loopback function, a common function on sound cards, can be enabled or disabled in software, it is set to the “on” position in factory condition.
    When the function is turned on, the music in the computer/mobile phone will be recorded at the same time with the instrument sound, it’s the same track mixed
    recording, including USB and BT music. If the function is turned off, when using the ME-01 as a sound card for recording, only the IN-interface instrument sounds can be recorded, which is more convenient for sub-track recording of instrument sounds during computer recording.
  • We will continue to improve our products and reserve the right to modify certain functions and specifications (including but not limited to appearance, packaging design, operation manual, accessories, dimensions, specifications, displays, etc.) without prior notice. Please confirm the product functions and specifications with the local distributor before the purchase. Product pictures and color due to the light error and screen admiration setting. It may be different from the physical product effect. Please refer to the physical object accordingly.

FCC Warning Statement
★ Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2)This device must accept any interference received, including interference that may cause undesired operation.

LEKATO logoThank you for choosing LEKATO products.
Please read this Owner’s manual thoroughly before using, and keep it in a safe place for later reference.
If there’s any questions regarding to this product, please feel free to contact us.
HOMCOM support@lekatotech.com
icon https://lekatotech.com

Documents / Resources

PDF thumbnailME-01 Multi Effects Processor
Owner's Manual · ME-01, ME01, 2BBZH-ME-01, 2BBZHME01, ME-01 Multi Effects Processor, Multi Effects Processor, Effects Processor, Processor

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.