8BitDo N30 Pro 2 Bluetooth Gamepad User Manual
N30 Pro 2 Bluetooth Gamepad Instruction
- Press start to turn on the controller
- Press & hold start for 3 seconds to turn off the controller
- Press & hold start for 8 seconds to force turn off the controller
Switch
1. Press & hold V & start to turn on the controller, LEDs will blink four times per cycle
2. Press & hold pair for 2 seconds to enter pairing mode, Blue LEDs will rapidly blink
3. Go to your Switch Home Page to click on Controllers, then click on Change Grip/Order. LEDs will enter its breathing mode when connection is successful
4. Controller will auto reconnect to your Switch with the press of start once it has been paired
- When connected to your Switch, star button= Switch Screen Shot button
- Home button= Switch HOME button
Android ( D – input )
1. Press & hold B & start to turn on the controller, blue LEDs will blink once per cycle
2. Press & hold pair for 2 seconds to enter pairing mode, Blue LEDs will rapidly blink
3. Go to your Android device’s Bluetooth setting, pair with [8BitDo N30 Pro 2]. LEDs will enter its breathing mode when connection is successful
4. Controller will auto reconnect to your Android device with the press of start once it has been paired
- USB connection: connect the controller to your Android device via USB cable after step 1
Windows (X – input)
1. Press & hold X & start to turn on the controller, LEDs will blink twice per cycle
2. Press & hold pair for 2 seconds to enter pairing mod a, Blue LEDs will rapidly blink
3. Go to your Windows device’s Bluetooth setting, pair with [8BitDo N30 Pro 2]. LEDs will enter its breathing mode when connection is successful
4. Controller will auto reconnect to your Windows with the press of start once it has been paired
• USB connection: connect the controller to your Windows device via USB cable after step 1
MacOS
1. Press & hold A & start to turn on the controller, LEDs will blink three times per cycle
2. Press & hold pair for 2 seconds to enter pairing mode, Blue LEDs will rapidly blink
3. Go to your macOS device’s Bluetooth setting, pair with [Wireless Controller]. LEDs will enter its breathing mode when connection is successful
4. Controller will auto reconnect to your macOS device with the press of start once it has been paired
- USB connection: connect the controller to your macOS device via USB cable after step 1
Turbo function
1. Hold the button you would like to set turbo functionality to and then press the star button to activate turbo functionality.
2. To deactivate turbo function, hold the button with turbo functionality activated and press the star button to deactivate turbo functionality
- Analog sticks are not included
- This does not apply to Switch
Battery
| Status | LED indicator |
| Low battery mode | LEDs in red |
| Battery charging | LEDs in yellow |
| Battery fully charged | LEDs turn off |
- Built-in 480 mAh Li-on with18 hours of playtime
- Rechargable via USB cable with1 – 2 hour charging time
Power Saving
- 1 minute with no Bluetooth connection, will power off
- 15 minutes with Bluetooth connection but no use, will power off
- Controller stays on and connected on wired USB connection
Support
Please visit support.8bitdo.com for further information & additional support
FAQ – Frequently Asked Questions
The differences are:
A. Shoulder button physical layout
SN30 Pro – two level placement for R1/R2 and L1/L2.
N30 Pro 2 – one level placement for R1/R2 and L1/L2.
B. LED indicators
SN30 Pro – four small LED lights placed on the bottom of the controller.
N30 Pro 2 – two long narrow curved lights on the sides.
C. Motor and thumb stick cap size
SN30 Pro – eccentric shaft gear motor and 17mm diameter thumb stick cap.
N30 Pro 2 – Linear vibration motor and 11mm diameter thumb stick cap.
When connected to Switch, you can find on this controller:
A. Screenshot = STAR button
B. Home button = Logo button
Turbo and NFC functions are not applicable here.
When connected to other devices, you can find on this controller:
A. STAR button = Turbo button
No, you can not wake up your Switch wirelessly with this controller.
It works with Switch, Windows 10, macOS, Android, Raspberry Pi.
It does auto reconnect to all the systems mentioned above with the press of START once they have been successfully paired.
No, it does not.
Just follow the procedure as below:
A. Press and hold Y+START to turn on the controller
B. Press and hold pairing button located at the bottom of the controller for 3 seconds to pair them
C. Find ‘Switch Pro support’ & ‘Nintendo button mapping’ and click on them
They are controller mode indicators:
A. When they blink once: D-input mode
B. When they blink twice: X-input mode (Xbox 360 mode)
C. When they blink 3 times: macOS mode
D. When they blink rapidly: Switch mode or pairing mode
E. Solid LEDs: connection is successful
We suggest you charge it via a phone power adapter.
The controller uses 480mAh rechargeable battery with 1-2 hour charging time. The battery can last up to 18 hours when fully charged.
Yes, you can. You can connect it to Switch, Windows 10, Android, Raspberry Pi and macOS.
Yes, they function as L3 and R3 when they are pressed down vertically.
10 meters. This controller functions the best within the range of 5 meters.
This might be caused by there are too many controllers connected to your Switch, as one Switch can take up to 10 controllers at a time maximum. Please follow the steps below to fix it:
A. Go to ‘System Setting’ on your Switch, then click on ‘Controllers and Sensors’ to disconnect the controllers which are connected to it
B. Restart your Switch
C. Press and hold Y+START to turn back on the controller. Press the pairing button on the bottom of the controller for 3 seconds
D. Go back to ‘System Settings’ and choose ‘Change Grip/Order’ to pair them
It uses a normal rumble, not HD rumble. .
It depends on the number of controllers each device can take. MultipleN30 Pro2 controllers can be used at a time.
Download
8BitDo N30 Pro 2 Bluetooth Gamepad User Manual – [ Download PDF ]
