Winsen ZPHS01C Multi-in-one Sensor Module
Isitatimende
Leli lungelo lokukopisha lemanuwali lingeka-Zhengzhou Winsen Electronics Technology Co., LTD. Ngaphandle kwemvume ebhaliwe, noma iyiphi ingxenye yale manuwali ngeke ikopishwe, ihunyushwe, igcinwe kusizindalwazi noma ohlelweni lokubuyisa, futhi ayikwazi ukusatshalaliswa nge-elekthronikhi, ukukopisha, izindlela zokurekhoda.
Siyabonga ngokuthenga umkhiqizo wethu. Ukuze uvumele amakhasimende ukuthi ayisebenzise kangcono futhi anciphise amaphutha abangelwa ukusetshenziswa kabi, sicela ufunde imanuwali ngokucophelela futhi ulisebenzise ngendlela efanele ngokuhambisana nemiyalelo. Uma abasebenzisi bephula imigomo noma besusa, beqaqa, beshintsha izingxenye ezingaphakathi kwenzwa, ngeke sibe nesibopho sokulahlekelwa.
Okucacile okufana nombala, ukubukeka, osayizi ... njll., sicela ngomusa kuyanqoba.
Sizinikela ekuthuthukisweni kwemikhiqizo kanye nokuqanjwa kabusha kwezobuchwepheshe, ngakho sigodla ilungelo lokuthuthukisa imikhiqizo ngaphandle kwesaziso. Sicela uqinisekise ukuthi iyinguqulo evumelekile ngaphambi kokusebenzisa leli bhukwana. Ngasikhathi sinye, ukuphawula kwabasebenzisi ekusetshenzisweni okulungiselelwe kwamukelekile.
Sicela ugcine imanuwali ngendlela efanele, ukuze uthole usizo uma unemibuzo ngesikhathi sokuyisebenzisa esikhathini esizayo.
I-Multi-in-One Sensor Module
UProfile
Le module ihlanganisa i-Electrochemical formaldehyde, inzwa ye-VOC ye-Semiconductor, inzwa yezinhlayiyana ze-Laser, inzwa ye-NDIR CO2 kanye nenzwa yokushisa & nomswakama. (Abasebenzisi bangakhetha inguqulo ye-CH2O noma inguqulo ye-VOC, abahambisani.)
I-Communication Interface: TTL serial/RS485, Baud rate:9600, data bit:8, stop bit:1, parity bit: none.
Isicelo
- Umtshina wegesi Ukuqapha izinga lomoya
- Isihlanzi somoya Isistimu ye-HVAC yekhaya elihlakaniphile
Ukucaciswa
| Imodeli | I-ZPHS01C |
| I-Target Gas | PM2.5, CO2, CH2O, TVOC,Izinga lokushisa & Nomswakama |
| Igesi yokuphazamiseka | I-Alcohol/CO gas...njll. |
| Ukusebenza voltage | I-5V (DC) |
| Isilinganiso samanje | 500 mA |
| Izinga lesikhombimsebenzisi | 3 V(ihambisana ne-3.3V) |
| Isignali yokuphumayo | UART/RS485 |
| Hlanganisa isikhathi | ≤ 3 iminithi |
| Ibanga le-CO2 | 400 ~ 5000ppm |
| PM2.5 ububanzi | 0 ~ 1000ug / m3 |
| CH2O ububanzi | 0 ~ 1.6ppm |
| Ibanga le-TVOC | 4 amabanga |
| Them. ububanzi | 0～65℃ |
| Them. ukunemba | ±0.5℃ |
| Hum. ububanzi | 0~100% RH |
| Hum. ukunemba | ±3% |
| I-Tem yokusebenza. | 0～50℃ |
| Ukusebenza Hum. | 15–80% RH(akukho ukufingqa) |
| Isikhathi Sokugcina. | 0～50℃ |
| Isitoreji Hum. | 0~60% RH |
| Usayizi | 62.5mm (L) x 61mm(W) x 25mm(H) |
Ithebula 1: ipharamitha yokusebenza
Ukubukeka Kwemojula
Usayizi wemojuli 
Umfanekiso wesi-3: Ubukhulu bokukhweza
Iphini Incazelo
- I-PIN1 GND Power input (itheminali yaphansi)
- I-PIN2 +5V Amandla okokufaka (+5V)
- I-PIN3 RX serial port (i-serial port receiver yamamojula)
- Imbobo yomkhiqizo ye-PIN4 TX (umthumeli wembobo we-serial wamamojula)
Ifomethi yephrothokholi yokuxhumana kwe-serial
Ikhompuyutha engusokhaya ithumela ifomethi
| Qala uhlamvu | ubude | Umyalo inombolo |
Idatha ye-1 | …… | Idatha n | checksum |
| IKHANDA | LEN | CMD | Idatha ye-1 | …… | Idatha n | CS |
| 11H | XXH | XXH | XXH | …… | XXH | XXH |
Ifomethi yephrothokholi enemininingwane
| Ifomethi yephrothokholi | Incazelo enemininingwane |
| Qala uhlamvu | Thumela i-PC ephezulu [11H]，Izimpendulo zemojuli [16H] |
| Ubude | Ubude bebhayithi yozimele = ubude bedatha+1 (kuhlanganisa i-CMD+DATA) |
| Umyalo No | Inombolo yomyalo |
| Idatha | Idatha efundiwe noma ebhaliwe, enobude obuguquguqukayo |
| I-Checksum | Okuphambene nesamba sokuqoqwa kwedatha |
Ithebula lenombolo yomyalo wephrothokholi ye-serial
| CHA. | Umsebenzi | Umyalo NO. |
| 1 | Ukufunda umphumela wokulinganisa | 0x01 |
| 2 | Ukulinganisa kwe-CO2 | 0x03 |
| 3 | Qala/Misa ukulinganisa uthuli | 0x0c |
Incazelo enemininingwane yephrothokholi
| Imodi yokulayisha esebenzayo:
Ukuthumela: 11 02 01 00 EC Impendulo: 16 0B 01 01A CO2 |
00 67 I-VOC/CH2O |
01 EA Umswakama |
03 04 Izinga lokushisa |
00 36 PM2.5 |
B4 CS |
Imodi ye-Q&A:
- Ukuthumela: 11 02 02 00 EB
- Impendulo: 16 0B 01 01 9A 00 67 01 EA 03 04 00 36 00 3C 00 20 B4
I-CO2 VOC/CH2O Izinga Lokushisa Lokuswakama PM2.5 PM10 PM1.0 CS
| Ukuhlonza | Idesimali ububanzi obuvumelekile | Inani elihambisanayo | amaningi |
| CO2 | 400 ~ 5000 | 400 ~ 5000ppm | 1 |
| I-VOC | 0 ~ 3 | 0 ~ 3 izinga | 1 |
| I-CH2O | 0 ~ 2000 | 0~2000μg/m3 | 1 |
| PM2.5 | 0 ~ 1000 | 0 ~ 1000ug / m3 | 1 |
| PM10 | 0 ~ 1000 | 0 ~ 1000ug / m3 | 1 |
| PM1.0 | 0 ~ 1000 | 0 ~ 1000ug / m3 | 1 |
| Izinga lokushisa | 500 ~ 1150 | 0 ~ 65℃ | 10 |
| Umswakama | 0 ~ 1000 | 0~100% | 10 |
- Inani lokushisa likhuphuka ngo-500 kusukela emiphumeleni yokulinganisa yangempela, okungukuthi, i-0 ℃ ihambisana nenani lika-500.
Inani lezinga lokushisa = (DF7*256+DF8-500)/10 - Inani elilinganisiwe limelelwa amabhayithi amabili, i-byte ephakeme ngaphambili kuyilapho ibhayithi ephansi ngemuva.
- Ngemva kokuthumela umyalo wokubuza, uma impendulo itholwa, imojuli izolayisha idatha njalo ngomzuzwana ngokuzenzakalelayo. Asikho isidingo sokuphinda umyalo ngaphambi kokuthi ugesi ucishwe.
I-Checksum nokubala
i-char engabhalisiwe i-FucCheckSum(i-char engabhalisiwe *i,unsigned char ln){
uhlamvu olungasayiniwe j,tempq=0; i+=1;
okwe(j=0;j<(ln-2);j++)
{
tempq+=*i; i++;
}
tempq=(~tempq)+1; buyisela (tempq);
}
Ukulinganisa kwephoyinti elinguziro le-CO2(400ppm).
- ukuthumela:11 03 03 01 90 58
- Impendulo: 16 01 03 E6
- Umsebenzi: CO2 ukulinganisa kwephuzu elinguziro
- Iziyalezo: Iphoyinti elinguziro lisho u-400ppm, sicela uqinisekise ukuthi inzwa isivele isebenza amaminithi angu-20 okungenani ezingeni lokuhlushwa elingu-400ppm ngaphambi kokuthumela lo myalo.
Qala & Misa ukulinganisa uthuli
- Thumela:11 03 0C DF1 1E C2
- Impendulo: 16 02 0C DF1 CS
- Umsebenzi: Qala/Yeka ukukala uthuli
- Umyalelo:
1, Phakathi kokuthumela umyalo, DF1=2 kusho ukulinganisa kokuqala, DF1=1 kusho ukumisa ukulinganisa; 2, Phakathi komyalo wokuphendula, i-DF1=2 isho ukulinganisa kokuqala, i-DF1=1 isho ukumisa ukulinganisa; 3, Lapho inzwa ithola umyalo wokulinganisa, ingena esimweni sokulinganisa okuqhubekayo ngokuzenzakalelayo. - Thumela:11 03 0C 02 1E C0 //ukuqala ukulinganisa uthuli
- Impendulo: 16 02 0C 02 DA //imojula “ikukalo luthuli endaweni”
- Thumela:11 03 0C 01 1E C1 //misa isilinganiso sothuli
- Impendulo: 16 02 0C 01 DB // imojula "ikukalwa kothuli olungekho esimweni"
Izixwayiso
- Inzwa ye-PM2.5 kule mojula ifanele ukutholwa kwezinhlayiya zothuli ezindaweni ezijwayelekile zasendlini. Indawo yokusetshenziswa kwangempela kufanele izame ukugwema indawo ezungezile yomsizi, izinhlayiya zothuli ngokweqile, indawo enomswakama ophezulu, njengalokhu: ikhishi, igumbi lokugezela, igumbi lokubhemela, ngaphandle, njll. Uma isetshenziswa endaweni enjalo, izinyathelo zokuvikela ezifanele kufanele zengezwe ukuze kuvinjelwe izinhlayiya ze-viscous. noma izinhlayiya ezinkulu ezivela ekungeneni kwenzwa, zakha i-buildup ngaphakathi kwenzwa, futhi zithinte ukusebenza kwenzwa.
- I-module kufanele igweme ukuthintana nama-solvents e-organic (okuhlanganisa i-silica gel nezinye izinto zokunamathisela), izigqoko, imithi yemithi, amafutha kanye namagesi aphezulu kakhulu.
- I-module ayikwazi ukufakwa ngokuphelele nge-resin material, futhi ayikwazi ukucwiliswa endaweni engenawo umoya-mpilo, ngaphandle kwalokho ukusebenza kwenzwa kuzolimala.
- Imojula ayikwazi ukusetshenziswa endaweni equkethe igesi ebolayo isikhathi eside. Igesi ebolayo izolimaza inzwa.
- Imojuli idinga ukufudunyezwa ngaphezu kwamaminithi angu-3 uma ivuliwe okokuqala.
- Ungayisebenzisi le mojula ezinhlelweni ezibandakanya ukuphepha komuntu siqu.
- Ungasebenzisi imojuli ekamelweni elincane, indawo ezungezile kufanele ingene umoya kahle.
- Ungayifaki imojula endaweni eqinile yomoya we-convection.
- Ungabeki imojula kugesi ephilayo ekugxilwe kakhulu kuyo isikhathi eside. Ukubekwa kwesikhathi eside kuzobangela inzwa eyiziro iphuzu ukukhukhuleka kanye nokululama kancane.
- Akuvunyelwe ukusebenzisa i-adhesive encibilikayo eshisayo noma i-sealant ukuze uvale imojuli ngezinga lokushisa elipholile elingaphezu kuka-80℃.
- Imojuli kufanele ibe kude nomthombo wokushisa, futhi igweme ukukhanya kwelanga okuqondile noma eminye imisebe yokushisa.
- Imojula ayikwazi ukudlidliza noma ukushaqeka.
I-Zhengzhou Winsen Electronics Technology Co., Ltd
Engeza.: NO.299 Jin Suo Road, National Hi-Tech Zone, Zhengzhou, 450001 China
Ucingo.: 0086-371-67169097 67169670
Ifeksi: +86- 0371-60932988
I-imeyili: sales@winsensor.com
Webindawo: www.winsen-sensor.com
Amadokhumenti / Izinsiza
 |
Winsen ZPHS01C Multi-in-one Sensor Module [pdf] Incwadi Yeziqondiso I-ZPHS01C, i-Multi-in-one Sensor Module, i-ZPHS01C Multi-in-one Sensor Module, Imojula Yezinzwa |
