1. Isingeniso
This manual provides detailed instructions for the safe and efficient operation of your ATOMSTACK A12 Pro Laser Engraving Machine. Please read this manual thoroughly before use to ensure proper setup, operation, and maintenance. Keep this manual for future reference.
Izexwayiso Zokuphepha:
- Always wear UV-filtering eye protection when operating the laser engraver.
- Ensure proper ventilation to dissipate fumes and smoke generated during engraving/cutting.
- Ungashiyi umshini ungagadiwe ngesikhathi sokusebenza.
- Gcina izinto ezivuthayo kude nendawo yokusebenza.
- Familiarize yourself with the emergency stop button location.
2. Okuqukethwe Kwephakheji
Qinisekisa ukuthi zonke izinto ezibalwe ngezansi zifakiwe kuphakheji yakho:
Figure 2.1: ATOMSTACK A12 Pro Laser Engraving Machine and included accessories.
- ATOMSTACK A12 Pro Laser Engraving Machine (Unibody Frame)
- Ikhanda le-Laser
- I-adaptha yamandla (24V, 5A)
- Ikhebula Lamandla
- Ikhebula le-USB (Uhlobo-C)
- Goggles (UV-filtering eye protection)
- Fixed Focus Lens
- Imaniwali yosebenzisayo
- Tools (H3 hexagon L-shaped wrench, M4 thumb screws)
- I-Flash Drive
- I-antenna ye-WiFi
- Silicone Hose (air hose)
- Wire Anchor
- Ikhebula Clamp
- 100*30 lint free cloth
- Isilayidi
- Shintsha ukhiye
3. Umhlahlandlela wokusetha
The ATOMSTACK A12 Pro features an unibody design for minimal assembly. Follow these steps to get started:
- I-Unboxing: Carefully remove the machine and all accessories from the packaging. The machine is pre-calibrated and shipped as a single unit.
Figure 3.1: The ATOMSTACK A12 Pro is ready to use right out of the box with its unibody design.
- Install the Slider: Attach the slider component to the designated rail on the machine. Secure it with the provided screws.
- Install the Laser Head: Mount the laser head onto the slider. Ensure it is firmly attached.
- Install the WiFi Antenna: Screw the WiFi antenna into its port on the machine's side.
- Install Tubing and X-axis Link Lines: Connect the tubing and X-axis link lines as shown in the diagram to ensure proper cable management and operation.
- Xhuma Amandla ne-USB: Plug the power adapter into the machine and a power outlet. Connect the USB cable from the machine to your computer.
- Vula: Insert the switch key and turn it to the ON position. The machine is now ready for software setup.
Video 3.1: A detailed guide on how to install and set up the ATOMSTACK laser engraver.
4. Iziqondiso Zokusebenza
4.1 Software Control
The ATOMSTACK A12 Pro supports multiple control methods:
- ATOMSTACK PC Software: Exclusive software for simplified operation, ideal for beginners.
- LightBurn & LaserGRBL: Traditional PC software for advanced users.
- ATOMSTACK Mobile APP: Available on Android and Apple App Stores for WiFi control via smartphone.
Umdwebo 4.1: Ngaphezuluview of the various software and app control options for the laser engraver.
4.2 Inqubo Yokuqopha
- Ukubekwa Kwempahla: Place your material flat on the engraving bed.
- Ukulungisa Ukugxila: Use the fixed-focus design for rapid and precise focusing in approximately 10 seconds.
- Cross Positioning: Utilize the newly added cross laser positioning feature for clear visibility of the laser's location, ensuring perfect alignment for engraving and easy horizontal adjustment.
- Izilungiselelo Zesofthiwe: Adjust engraving parameters (speed, power, passes) in your chosen software based on the material.
- Qala Ukuqopha: Qalisa inqubo yokuqopha kusuka kusoftware.
Figure 4.2: The cross positioning system helps align objects and lock to edges for precise horizontal carving.
5. Features & Capabilities
- Idizayini ye-Unibody: Sturdy all-aluminum unibody design, installation-free and pre-calibrated.
- High Speed & Precision: New dual-axis linear guide rail structure and high-speed motherboard allow engraving speeds up to 600mm/s, 3-6 times faster than traditional frame machines. Accuracy within 0.004 inches.
- I-Laser enamandla: 12000mW diode laser (Laser Class 4) with 50W machine power and a 0.05*0.06mm ultra-fine laser spot focus.
- Thicker Cuts: Can cut through 8mm wood, 5mm black acrylic, and 0.02mm stainless steel in a single pass.
- Diverse Material Compatibility: Engraves and cuts a wide range of materials including wood, acrylic, metal, glass, ceramics, leather, paper, cardboard, and more.
- Automatic Power Failure Recovery: Memorizes engraving position and swiftly resumes from the paused point, ensuring uninterrupted production and material saving.
- Ukuvikeleka Okuthuthukisiwe: Equipped with 4-way limit switches, UV-filtering eye protection, a tilt detector with a 15-degree alarm, and an emergency stop button.
Figure 5.1: Comparison showing the significantly faster engraving speed of the A12 Pro.
Figure 5.2: Demonstrates the maximum cutting thickness for various materials with the A12 Pro.
Umfanekiso 5.3: Eksamples of various materials that can be engraved or cut by the machine.
6. Isondlo
- Ukuhlanza ilensi: Regularly clean the laser lens with the provided lint-free cloth to maintain optimal performance and prevent residue buildup.
- Ukugcotshwa kukaloliwe: Periodically apply a small amount of lubricant to the guide rails to ensure smooth movement of the laser head.
- Ukususwa Kwemfucumfucu: Keep the engraving bed and surrounding area free of debris and dust. Use an air compressor or brush to clear away small particles.
- Ukuvuselelwa kwe-Firmware: Check the official ATOMSTACK website periodically for firmware updates to ensure your machine has the latest features and bug fixes.
7. Ukuxazulula izinkinga
| Inkinga | Imbangela Engenzeka | Isixazululo |
|---|---|---|
| Umshini awuvuli amandla | Power cable loose; Emergency stop engaged; Key not turned. | Check power connections; Disengage emergency stop; Turn key to ON. |
| I-laser ayidubuli/okukhiphayo okubuthakathaka | Lens dirty; Incorrect focus; Low power setting in software. | Clean laser lens; Adjust focus; Increase power setting. |
| Engraving is distorted/inaccurate | Loose belts/rails; Material shifting; Incorrect software settings. | Check and tighten belts/rails; Secure material; Verify software settings. |
| Software not connecting to machine | USB cable issue; Driver not installed; Incorrect COM port. | Try different USB port/cable; Install drivers; Select correct COM port in software. |
8. Imininingwane
- Ubukhulu bomkhiqizo: 23.22 x 23.22 x 7.08 amayintshi
- Isisindo Sento: 18.74 amakhilogremu
- Amandla Okukhipha I-Laser: 12000mW (12W)
- Amandla Omshini: 50W
- Usayizi wendawo ye-Laser: 0.05*0.06mm
- Isivinini Sokuqopha: Kufika ku-600mm/s
- Ukunemba: Within 0.004 inches
- Ukuxhumana: USB, WiFi (via Mobile APP)
- Isofthiwe Esekelwe: ATOMSTACK PC Software, LightBurn, LaserGRBL
- Umkhiqizi: I-Shenzhen AtomStack Technologies Co., Ltd.
- Izwe azalelwe kulo: China
9. Iwaranti kanye Nokusekela
Your ATOMSTACK A12 Pro Laser Engraving Machine comes with a standard manufacturer's warranty. For detailed warranty information, technical support, or service inquiries, please refer to the warranty card included in your package or visit the official ATOMSTACK webindawo.
Our professional technical and support teams are available 24/7 to answer any questions or concerns you may have.
