ZOSI C280A IP WiFi Security Camera User Guide

What’s in the Box

• Camera
  
• Power Adapter
  
• Mounting Screw Bag
  
• Mounting Template
  
• Warning Stickers
  
• Quick Start Guide
  

NOTE : The number of accessories varies with the camera model you purchased.

Camera Structure Diagram

Connection Diagram

1. Connect the camera and NVR to the power supply.
2. After the device is powered on, the NVR will automatically search and pair with the camera, and the camera feed will be displayed.

NOTE: If you have purchased a new camera, it needs to be paired before it can be added to the system. For detailed pairing operations, please refer to the following link:
To add additional cameras to the NVR, follow these steps:

1. Power on the camera and connect the NVR and camera with an Ethernet cable.
2. Right-click on the screen to open the menu.
3. Select “IPC Channel Configuration” and click the “Search” button.
4. Click “Add All” to connect the cameras. A “Connected” status indicates a successful connection.
5. Disconnect the Ethernet cable from the camera and NVR, and wait for the camera to switch to WiFi mode.

Install the Camera

1. Installation Precautions
   • Avoid directing the camera towards strong light or reflective objects, including sunlight, lights, glass, mirrors and other areas with strong refraction of light sources.
   • Do not install at location with objects covering or obscuring the camera.
   • Avoid mounting the camera in places where too dim, and point the camera towards a well-lit area. For better image quality, make sure the camera and the captured subject are at the same lighting conditions.
   • For better image quality, it is recommended to clean the lens with a soft cloth from time to time.
   • Do not expose the power port to water or moisture, or blocked by dirt or other things.
   • Do not install the camera where rain and snow may hit the lens directly.
   • Camera may work in extremely cold conditions as low as -10°C because it will produce heat when powered on. You may power the camera indoors for a few minutes before installing it outdoors (Only for outdoor cameras)

NOTE:

1. Set up the network before installing the camera.
2. Run the cables through the cable notch on the mount base before installing the camera.

A : Mount the Camera to the Wall

1. Drill holes according to the mounting template and insert the anchors.
2. Install the mount base with screws.
3. Install the top bracket of the camera to the base and tighten the knob of the camera bracket.
4. To adjust the camera direction, you may control the camera to pan and tilt via Zosi App or Client.
   

B : Mount the Camera to the Ceiling

1. Drill holes according to the mounting template and insert the anchors.
2. Install the mount base with screws.
3. Install the top bracket of the camera to the base and tighten the knob of the camera bracket.
4. To adjust the camera direction, you may control the camera to pan and tilt via Zosi App or Client.
   

Installation Distance, Height and Angle

Distance : Best accuracy for objects within 5-50 ft (1.5-15 m).
Angle : Tilt the camera down about 30°-60°from the horizontal position.
Height : Install the camera 8-16 ft (2.5-5m) above the ground.

Install the camera 8-16 ft (2.5-5m) above the ground.

NOTE : The accuracy of human detection will be affected by various factors, such as the distance between the person and the camera, the height of the person, the height and angle of the camera, etc. The accuracy and distance of detection will also be affected in
the night vision environment.

FAQ

Q: Does the camera support motion detection and image capture?

A: It captures images automatically when people, are detected or when there is a change in detected images. Users can also manually capture images using our ZOSI Smart APP.

Q: The Wireless Connection of the Camera is Not Working during Pre-installation Testing?

A: Please try resetting the camera and connecting it to the NVR with an Ethernet cable before adding it.

Q: The Camera is Not Powered On?

A: If the camera still cannot be powered on after changing the power supply, please check if the camera's infrared lights are lit. If the infrared lights are not lit,, the camera may be damaged and needs to be returned or exchanged.

Notification of Compliance

1. FCC Compliance Statement
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including inference that. may cause undesired operation.
   Simplified EU Declaration of Conformity

ZOSI declares that the device is in compliance with the essential requirements and other relevant provisions if Directive 2014/53/EU.
Correct Disposal of this Product
This marking indicates that this product cannot be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal and promote the sustainable reuse of material resources, please recycle it responsibly. To return your used device, please visit the Return and Collection System or contact the retailer from whom the product was purchased. They can take this product away for environmentally safe recycling.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any  interference received, including interference that may cause undesired operation.

RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

For USA: The frequency stability of all transmission frequencies of U-NII-1, U-NII 2A, U-NII 2C and U-NII-3 meets the requirements of 47 CFR FCC Part15.407(g), and the manufacturer declares that their transmission is maintained at Band U-NII-1, U-NII 2A, U-NII 2C and U-NII-3.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subje ct to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

ISED Radio Frequency Exposure Statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in mobile exposure conditions. The min separation distance is 20 cm.
ISED Déclaration d’exposition aux radiofréquences:

Operation of this device is restricted to indoor use only. (5150-5350MHz)

For Canada : The frequency stability of all transmission frequencies of U-NII-1, U-NII 2A, U-NII 2C and U-NII-3 meets the 47 CFR FCC Part15.407(g) requirements, and the manufacturer states that their transmissions remain within the U-NII-1, U-NII 2A, U-NII 2C and U-NII-3 bands.

For more information, please visit : https://www.zositech.com
Support Email: service@zositech.com

Documents / Resources

ZOSI C280A IP WiFi Security Camera [pdf] User Guide C280A, C186, C188, C289, C280A IP WiFi Security Camera, C280A, IP WiFi Security Camera, WiFi Security Camera, Security Camera, Camera

References

• User Manual