ZigBee WZ1 RF 2CH LED Controller User Manual

ZigBee & RF 2CH LED Controller
Model No.: WZ1
User Manual

Tuya APP cloud control/Philips HUE control/Voice control/2 Channels/Push-Dim/DC power socket input

Features

• Used for control single color or color-temperature LED strip.
• DC power socket input and 2-channel constant voltage output.
• Tuya APP cloud control, supports on/off, color temperature and brightness adjust, delay turning on/off light, timer run, scene edit, and music play function.
• Philips HUE APP control by connecting with Philips HUE bridge.
• Voice control, support amazon ECHO and Tmall Genie smart speakers.
• Match with optional RF 2.4 G remote control
• User needs to set the light type by pressing the key before Tuya APP network connection and match the RF remote of the same light type.
• Each WZ1 controller can also work as a ZigBee-RF converter, then use Tuya APP to control one or more RF LED controllers or RF LED dimming driver synchronously.
• Connect with an external push switch to achieve on/off and 0-100% dimming function.
• Light on/off fade time 3s selectable.

Technical Parameters

Input and Output

Dimming data

Safety and EMC

Environment

Warranty and Protection

Mechanical Structures and Installations

WZ1 ZigBee & RF 2CH LED Controller

System wiring

Note:

1. The above distance is measured in a spacious (no obstacle) environment,
   Please refer to the actual test distance before installation.
2. Users must use the Tuya ZigBee gateway to realize remote control and voice control.

Wiring Diagram

● For single color

Dimming remote
Press and hold the match/set key for 8s, until the RUN LED indicator turns white, then release; the controller will become DIM type, then do smart config by Tuya APP, or short press the match key to match with the dimming RF remote.

● For dual color CCТ

CCT remote
Press and hold the match/set key for 10s, until the RUN LED indicator turns yellow, then release; the controller will become CCT type, then do smart config by Tuya APP, or short press the match key to match with the CCT RF remote.

Note:

1. User can connect a constant voltage power supply or power adapter as power input.
2. Press and hold the Match/Set key for 2s to switch between 2 kinds of light type in sequence.
3. Switch off the power, then switch on the power, repeat again.
   Immediately short press match key 3 times; the light on/off time will change between 3s and 0.5s.
4. For CCT light, continuous power on and off will change 3 levels of color temperature (WW, NW, and CW) in sequence.

Push Dim

Tuya APP network connection

Press and hold Match/Set key for 2s:
Switch 2 kinds of light type in sequence; notice this operation does not automatically clear previous network connection.
Press and hold the Match/Set key for 5s, or push the Match/Set key twice quickly, or press and hold the Match/Set key for 8 or 10s to set 2 kinds of light type:
Clear the previous network connection, enter config mode; the purple LED indicator fast flashes, and the output LED will flash 10 times.
Repeat powering on and off for 5 consecutive times; also clear the previous network connection, enter config mode, and the output LED will flash 10 times.
If the Tuya APP network connection succeeds, the RUN LED indicator will stop flashing purple and turn the corresponding light type color (White: DIM, Yellow: CCT). And in the Tuya APP, you can find the ZB-DIM or ZB-CCT device

Tuya APP interface

DIM:
Touch the brightness slider to adjust brightness.

CCT:
Touch the color wheel to adjust color temperature.
Touch the brightness slider to adjust brightness.

WZ1 match remote control (Optional)

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the WZ1’s Match key
Match:
Short-press the match key of WZ1, immediately press the on/off key (single zone remote) or zone key (multiple zone remote) on the remote.
The LED indicator fast-flashes a few times means the match is successful.
Delete:
Press and hold the match key of WZ1 for 15s to delete all matches.
The LED indicator fast-flashes a few times means all matched remotes were deleted.

Use Power Restart
Match:
Switch off the power of WZ1, then switch on the power; repeat again.
Immediately short-press the on/off key (single-zone remote) or zone key (multiple zone remote) 3 times on the remote.
The light blinking 3 times means the match is successful.
Delete:
Switch off the power of WZ1, then switch on the power, repeat again.
Immediately short-press the on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote
The light blinking 5 times means all matched remotes were deleted.

WZ1 works as a ZigBee-RF converter to match the RF LED controller or dimming driver
End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key
Match:
Short-press the match key of the controller, immediately press the on/off key on the Tuya APP.
The LED indicator fast-flashes a few times means the match is successful.

Delete:
Press and hold the match key of the controller for 5s,
The LED indicator fast-flashes a few times means the match was deleted

Use Power Restart
Match:
Switch off the power of the controller, then switch on the power; repeat again.
Immediately short-press the on/off key 3 times on the Tuya APP.
The light blinking 3 times means the match is successful.
Delete:
Switch off the power of the controller, then switch on the power; repeat again.
Immediately short-press the on/off key 5 times on the Tuya APP.
The light blinking 5 times means the match was deleted