ZigBee RGBW LED Light Device

Important: Read All Instructions Prior to Installation

Function introduction

Note: W channel can only be controlled through color temperature control command since Zigbee only has tunable white control. Color temperature control will mix RGB channels as 1 channel white and then make color tuning with the 4th channel white.

Product Data

No.	Input Voltage	Output Current	Output Power	Output Type	Dimension (LxWxH)
1	12-36VDC	4CH, 5A/CH	240-720W	Constant voltage	170×53.4x28mm
2	12-36VDC	4CH, 0.35A/CH	16.8-50.4W	Constant current	170×53.4x28mm
3	12-36VDC	4CH, 0.7A/CH	33.6-100.8W	Constant current	170×53.4x28mm

• ZigBee RGBW LED light device based on latest ZigBee 3.0 protocol
• Enables to control ON/OFF, light intensity and RGB color of connected RGBW LED lights
• W channel can only be controlled through color temperature control command
• Color temperature control will mix RGB channels as 1 channel white and then make color tuning with the 4th channel white
• ZigBee end device that supports Touchlink commissioning
• Supports self-forming zigbee network without coordinator
• Supports find and bind mode to bind a ZigBee remote
• Supports zigbee green power and can bind max. 20 zigbee green power remotes
• Compatible with universal ZigBee gateway products
• Waterproof grade: IP20

Safety & Warnings

•  DO NOT install with power applied to device.
• DO NOT expose the device to moisture.

Operation

1. Do wiring according to connection diagram correctly.
2. This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
   Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually”.
   Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
   
4. TouchLink to a Zigbee Remote
   
   Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
   2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
   3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
   4) After TouchLink, the device can be controlled by the linked remotes.
5.  Removed from a Zigbee Network through Coordinator or Hub Interface
   
6. Factory Reset Manually 
   
7. Factory Reset through a Zigbee Remote (Touch Reset)
   Note: Make sure the device already added to a network, the remote added to the same one or not added to any network.
   
8. Find and Bind Mode
   
9. Learning to a Zigbee Green Power Remote
   
10. Delete Learning to a Zigbee Green Power Remote
    
11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)
    
    Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals.
    Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals
    Note: 1) Each added device can link and be controlled by max. 30 added remotes.
    2) Each added remote can link and control max. 30 added devices.
12. ZigBee Clusters the device supports are as follows:
    Input Clusters
    • 0x0000: Basic • 0x0003: Identify • 0x0004: Groups • 0x0005: Scenes
    • 0x0006: On/off • 0x0008: Level Control • 0x0300: Color Control • 0x0b05: Diagnostics
    Output Clusters
    • 0x0019: OTA
13. OTA

The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically.

Wiring Diagram

Documents / Resources

ZigBee RGBW LED Light Device [pdf] Instruction Manual RGBW LED Light Device, RGBW Light Device, LED Light Device, Light Device

References

• User Manual