ZigBee 3.0 Wireless Push Button Smart Scene Switch Controller User Manual

ZigBee 3.0 Wireless Push Button Smart Scene Switch Controller

Product Information

Features

• Can be controlled by iOS phone/Android phone
• Support “Smart Life” and “Tuya Smart” APP
• Voice control: Compatible with Alexa and Google home T mall Genie or Xiaodu speakers
• Timing function: Auto on/off with timing function
• Overload protection for easy replacement of your traditional mechanical switches (needs neutral)
• Smart scene
• Device group

Security Information

Risk of electric shock: Electricity can cause personal injury and properly damage if not handled properly. If you are unsure of any part of these instructions, seek professional help from a qualified electrician.

Install

Notice:

• Make sure the power on the circuit breaker is turned off before wiring.
• Neutral wire is required. Verify that the wall box contains a neutral wire (usually white). If the wall box does not have a neutral wire, try another location in the home or call a professional electrician to install the switch.
• The wire colors indicated in this manual are the usual colors and may vary in some houses.
• Make sure the wire conductors are securely attached to each screw.
• Make sure the Wi-Fi signal is stable and working properly before wiring.
• If you do not have any wiring experience, please call a professional electrician.

First Step:

• Turn off the circuit breaker and test the power with an electrical tester.
• Make sure the switch is off before wiring.

Second Step:

• Remove existing wall panels; turn on power at breaker and use electrical tester to check which wire is the line; the tester will beep when near the line.
• Turn off the power at the circuit breaker; if there is a power outage, use an electrical tester, pull the existing switch out; mark the wiring and other wires; disconnect the power with pliers and remove the wires from the existing switch.
• Connect the switch wires to the wall box with the wire conductors according to the wiring diagram below.
• Third step: Install the switch using the screws provided and snap the wall plate onto it.
• The fourth step: Turn the power back on at the circuit breaker, then turn on the lights.

Wiring Diagram

The Live wire is connected to the “L” terminal, The Neutral wire is connected to the “N” terminal, Lighting wire is connected to “L1, L2, L3” terminals.

1. Gang switch lighting wire connection: “L1” terminal
2. Gang switch lighting wire connection: “L1,L2” terminals
3. Gang switch lighting wire connection: “L1,L2,L3” terminals

Add device

Add device to “Smart Life” or “Tuya Smart” APP

1. Step 1: Download and install the “Smart Life” or “Tuya Smart” APP: Scan the QR code below
   
2. Step 2: Enter the phone settings option, turn on the Bluetooth and WiFi functions, and turn on the product at the same time
3. Step 3: Open the Smart Life APP, register and log in your account, if you have a Smart Life account, just log in.
4. Step 4: Power on after the wiring is completed, the device is powered on by default, press and hold the touch wall switch button for about 8, until the WiFi blue LED flashes quickly, enter the network configuration mode
5. Step 5: Enter the App, click the “+” at the top right of the page to enter the network connection page.
6. Step 6: Make sure your device’s light is blinking quickly(2 times per second) tap to proceed to the next steр.
7. Step 7: Enter your WiFi and password
8. Step 8: Name your device.
9. Step 9: When the WiFi LED is on, the device is online.
   Take control now!

How to use smart speakers to control devices, such as Amazon Alexa, Google Assistant or T mall Genie?
Open the Smart Life app to enter the “Me” view and find the user Quide for “Me” view and find the user guide the corresponding smart speaker

【Note: Before using the smart speaker, please log in to your account on Amazon Alexa Google Assistant, or T mall Genie.]

Introduction of RF remote control operation

Packaged products are paired at the factory and do this wirelessly. If you need to add or replace the remote control switch, please refer to the following steps

Pairing method
Press and hold the touch wall switch button for about 3 seconds. The red LED indicator lights up to enter the RF433 pairing mode. At this time, press the RF433 remote control switch a few times and the indicator light flashes off. The switch is controlled and paired successfully.

Code clearing method

Long press the touch wall switch button for 5 seconds until the red LED indicator flashes 3 times, the code is cleared successfully.