Keilton Basic RM51 灯具传感器遥控器
描述
The RM51 Remote is used to program the configurations of the Keilton Basic sensors using infrared (IR) communications with the devices. It offers 6 default modes of configurations plus manual settings. Customer configurations can be created, saved, and then sent to each device, ensuring a rapid deployment.
特征
- 低功耗。
- Infrared communication.
- Setting most of the Keilton Sensors G2.
- Custom Configurations can be saved to A, B, C, D, or For.
- 40′ maximum IR range.
- RML (included with new orders, available as an accessory for order), installed, will increase the IR range. (See table below)
规格
订购信息
| 模型 | 描述 |
| RM51.A0 | Basic Sensor Controller RM51 |
| RM51.A1 | Basic Sensor Controller RM51 With RML |
订购信息 – 配件
| 模型 | 描述 |
| RMLS | Extended IR range for commissioning |
方面
产品标签
远程指令
记忆模式（调试）
To begin commissioning, follow these steps:
- 选择内存专业版file：A、B、C、D 或 E。
- The remote’s indicator lights will flash, indicating the currently saved settings.
- Settings can be configured by pressing the appropriate buttons in the highlighted gray area of the remote (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review the selected settings and make changes as needed.
- Point the remote at the desired luminaire and press “SEND.”
- The luminaire will flash twice to confirm that he settings are saved. Changing a parameter in a memory profile will automatically override previous settings.
- If configuring multiple luminaires, repeat steps 4 and 5 after selecting the configured memory mode.
E Mode allows for visual adjustment to choose the desired dimming level.
日光采集（F 模式）
Continuous Adjustment Mode adjusts dimming levels based on daylight.
- Point the remote at the desired luminaire and press “ON,” then press DIM+ or DIM- to adjust the dimming level.
- Press “F.” The indicator lights on the remote will show the current saved settings. Note: Only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings
- Review the selected settings and make changes as necessary. Press “SEND.”
- If the configuration is successful, the luminaire will flash twice to confirm that the setting is saved. If configuring multiple luminaires, select the configured Daylight Harvesting settings, then follow steps 1, 2, and 3.
附加远程功能
| ON | 转数 ON 灯具。 |
| 离开 | 转数 离开 灯具。 |
|
测试 |
The fixture enters the test mode and exits automatically after 5 minutes. The test mode parameters are configured as follows: Trim-level: 100%， 敏感度： 高的， 保持时间： 2s， Standby dim: 50%， 待机时间： 2 年代。 |
| 重置 | Trim= 100％, Sensitivity = 高的, T1 = 5 分钟, Standby Dim = 30％, T2 = 60 分钟,
Photocell = 离开. |
| 昏暗+/- | Press Dim+ or Dim- to adjust brightness in 0.5V increments. Hold the button for continuous
调光 |
| 修剪级 | Set the Maximum brightness. |
| 敏感度 | Set the motion sensitivity of the sensor 低的：50% / 高的：100%，
关： disable the motion detection function. |
| 保持时间 | 在转换到待机暗态之前，未检测到占用情况的持续时间。 |
| 待机昏暗 | Select any standby dim level. |
| STANDBY 时间 | Standby time, when the time is set to “∞”, the daylight detection function is activated. |
| 光电池 | visible light threshold, the fixture is allowed to be turned on when it falls below the threshold
低的：5fc / 高的：20fc, 加州航空: Collect the current visible light illuminance as the threshold, 关： disable PHOTOCELL function. |
| 模式 | Default configuration parameters for modes A 到 F. |
| 发送 | 将设置发送到传感器。 |
| 默认 模式A | Trim= 100％, Sensitivity = 低的, T1 = 30 分钟, Standby Dim = 50％, T2 = ∞, Photocell = 加州航空. |
| 默认模式 B | Trim= 100％, Sensitivity = 低的, T1 = 30 分钟, Standby Dim = 50％, T2 = 15 分钟, Photocell = 加州航空. |
| 默认模式 C | Trim= 100％, Sensitivity = 低的, T1 = 30 分钟, Standby Dim = 50％, T2 = 15 分钟, Photocell = 离开. |
| 默认模式 D | Trim= 50％, Sensitivity = 低的, T1 = 30 秒, Standby Dim = 50％, T2 = 30 分钟, Photocell = 加州航空. |
| 默认模式 E | Manual Dimmer Mode, Trim 100％. |
| 默认模式 F | Daylight Harvesting, Trim= 50％, Sensitivity = 低的, T1 = 15 分钟. |
联系我们
- 7001 Columbia Gateway Drive, Suite 210, Columbia, MD 21046, USA
- 电话：+1 443-320-2233 (M-F 9 am-5 pm ET)
- E: support@autani.com
常见问题解答
How do I change the memory profile 设置？
Select the desired memory profile on the remote and adjust settings as needed before pressing SEND to save
Can I configure Daylight Harvesting settings for multiple luminaires simultaneously?
No, you need to configure Daylight Harvesting settings for each luminaire individually using the F Mode on the remote.
What is the expected operation if the user sets Standby Time to something other than INFINITE?
moiton -> the intensity of ambient light is lower than the threshold set by the PC->turn on the light and dim to trim-level->t1 timeout->dim to standby dim ->t2 timeout->turn off the light.
If it does not turn OFF the fixture, why would Mode B and D use CAL as the default?
The ambient light intensity stored by CAL will serve as the threshold for turning on the lights, but it has no connection with the function of turning off the lights.
文件/资源
 |
Keilton Basic RM51 灯具传感器遥控器 [pdf] 用户手册 RM51.A0、RM51.A1、RM51 灯具传感器遥控器、RM51、灯具传感器遥控器、灯具传感器、灯具传感器 |