ZEPHYR FZSATJ-3 Battery Sprayers User Guide

A: Yes, you can use essential oils with the sprayer. However,
make sure to thoroughly clean the sprayer after each use with warm,
soapy water to prevent damage.

Q: What should I do if the power switch is not functioning
correctly?

A: If the power switch is not working correctly, do not operate
the sprayer. Contact customer support for assistance and do not
attempt to make adjustments or use the sprayer.

Q: How should I store the sprayer?

A: Store the sprayer in a cool, dry place away from children and
untrained users. Disconnect the battery pack when not in use to
prevent accidental starting.

“`

View Fullscreen

ZEPHYR OPERATION GUIDE

FZSATJ-3

OPERATION GUIDE
Model #: FZSATJ-3

BATTERY POWERED BACKPACK SPRAYER
4-GALLON TANK CAPACITY
– 1 –

ZEPHYR OPERATION GUIDE FZSATJ-3

ATTENTION !

Please read the following information carefully. User must read and understand the entire manual

before operating the sprayer. Failure to follow instructions or improper use could lead to sprayer failure

and possible serious injuries.

· DO NOT RETURN SPRAYER TO · Read and follow all instructions

STORE. If you experience issues

and cautions on label of products

chemical spray from drifting into unintended areas.

NOTES

or have questions, contact our

used in this sprayer.

· Keep sprayer and all chemicals out

Support Team M-F 9am-5pm · Do not store your sprayer in

of the reach of children.

· The sprayer may have residual

EST at 1-803-339-2500 or email

extremely high temperatures. · Remove chemicals and thoroughly

water in it when first opened.

support@wessol.com. · Never spray flammable, caustic,

Heat can lead to the build-up of pressure within the sprayer,

clean the sprayer after each use. Failure to clean the sprayer

This is due to quality testing every sprayer undergoes before leaving

acidic, heat, pressure, or gas

resulting in a possible explosion.

producing chemicals.

· Do not try to make modifications to

may cause contamination of

our factory.

subsequent applications, will · Some parts may be located

· Always read and follow chemical

manufacturer’s

instructions

the sprayer. Always use FlowZone® branded replacement parts from

cause premature spray ware, and void the sprayer warranty.

under the tank lid or in the battery compartment when first

before use with this sprayer as

the manufacturer.

assembling the sprayer.

some chemicals may be hazardous · Do not use batteries that are wet

when used with this sprayer.

or have been damaged.

· Never leave chemicals or solutions · Inspect sprayer hose, power knob,

sitting in your sprayer after using.

wand, and gun for damage or loose

· After using sprayer with

connections before each use.

chemicals, it is important to spray · Do not lift or carry the sprayer by

with fresh water for 3-5 minutes to

the hose, or wand. Carry by the

ensure residual chemicals in the

handle only.

NEVER spray petroleum oil

THIS SPRAYER IS DESIGNED TO OPERATE WITH ONLY FLOWZONE®

distillates, or acetone through

BRANDED BATTERIES AND

your sprayer. If using essential

ADAPTERS. ANY OTHER

oils, thoroughly clean the

BATTERIES COULD CAUSE

sprayer after each use with

SERIOUS HARM OR INJURY TO

warm, soapy water.

THE OPERATOR AND SERIOUS DAMAGE TO THE SPRAYER.

gun, wand, tank, pump, and hose · Only spray when the air is calm (no

are cleaned out.

wind or air movement) to prevent

When using chemicals, always wear protective clothing, including respiratory

protection masks, gloves, eye protection, etc.

This product contains chemicals, including lead, known to the state of California to cause birth defects and other reproductive harm.

Do not dispose of Lithium-ion batteries with household waste; recycle where facilities exist.

– 2 –

ZEPHYR OPERATION GUIDE FZSATJ-3

OPERATING
· Do not allow familiarity with products to make you careless. Remember that a single moment of carelessness is sufficient to cause serious injury.
· Always wear eye protection with side shields when handling or operating this sprayer. Failure to do so could result in serious injury from chemical contact or flying dirt or debris.
· The Lithium-ion battery pack can be used in temperatures down to 32ºF. When operating in cold temperatures, put the battery pack in the battery compartment and use the sprayer in a light duty application. After about a minute the battery pack will warm up and begin operating normally.
· Always use the correct power setting for your application. Using the correct PSI and flow rate will result in a safer and more thorough treatment. For calibration resources please contact FlowZone® technical support. (Note: Always refer to local, state, and federal laws and regulations regarding your application.)

· Do not use the sprayer if the
power switch is not functioning
correctly. Any power tool that cannot be controlled with the switch is dangerous and must be
repaired. · Remove battery before making
any adjustments, changing
accessories, or storing the
sprayer. Disconnect the sprayer from the power source by removing the battery pack.
These preventative safety
measures reduce the risk of
starting the sprayer accidentally.

STORING

· Store sprayer out of reach of

children and do not allow persons

unfamiliar with the power tool

or these instructions to operate

the sprayer. Power tools are

dangerous in the hands of

untrained users.

· Maintain

sprayers

and

accessories. Check for misalignment or binding of

moving parts, breakage of parts

and any other condition that may

affect the sprayers operation.

SAFETY

· Use the sprayer and accessories

in accordance with these

instructions, taking into

consideration the working conditions and the work to be

performed. Use of this sprayer

for applications that it was not

intended for could result in a hazardous situation.

Keep handles and lift points dry, clean and free from oil and

grease. Slippery handles and lift points do not allow for safe

handling and control of the

sprayer. · Risk of fire or explosion: Never

use this sprayer with liquids such

as gasoline, ethanol, methanol, or any other flammable or gas

producing chemicals. Do not use sprayer around sparks, flame, or

smoke. Failure to adhere to these

instructions may cause ignition,

resulting in potential injury and

damage to property.

To reduce the risk of fire,
personal injury, and product
damage from a short circuit,
never immerse the sprayer, battery, or charger in fluids. Do
not place or store sprayer where it could fall or be pulled into a tub
or sink. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products,
etc., can cause a short circuit. Electric shock hazard: Never
spray toward electrical outlets. Spray area must be well ventilated to avoid hazardous fume build-
up. Always refer to the product label of the chemical being used
for safety instructions and proper
use practices.
Avoid spraying on windy days.
Spraying in windy conditions could cause chemicals to be blown onto persons, plants, or objects that are not intended to be sprayed.

DO NOT RETURN SPRAYER TO STORE, if you experience problems or have
questions contact our Customer Support, M-F 9am-5pm EST at +1 803-339-2500, or email: support@wessol.com, or find more information
at fzspray.com/pages/troubleshoot.

– 3 –

ZEPHYR OPERATION GUIDE FZSATJ-3

SAFETY CONT.

· Always use common sense and be cautious when

·
· ·

Do not store chemicals in the

tank. Chemicals can degrade

seals and hoses. Drain and

clean sprayer after each use.

Failure to do so may void the

sprayer warranty. Remove gloves before handling

battery pack. Chemicals may be damaging to plastics.

Thoroughly inspect the interior,

exterior, and all components of the sprayer before each

use. Check for cracked and

using the sprayer. It is not possible to anticipate every

situation that could result in

a dangerous outcome. Do not

use this sprayer if you do not

understand these operating

instructions or if you feel the work is beyond your capability.

Maintain

labels

and

nameplates. These carry

important information. If unreadable or missing, contact

FlowZone® Support.

deteriorated hoses, leaks, clogged nozzles and missing

or damaged parts. If damaged,

ensure the sprayer is repaired

before use. Many accidents are

caused by poor maintenance.

Always remove the battery

pack from the sprayer before

Manuals are subject to updates. Scan the QR code to view the most updated manual online!

performing any maintenance,

storing or draining of the

sprayer.

· Do not eat or smoke while

handling or operating the

sprayer. Refer to the product label of the chemical being

used for user safety practices. · Do not use the battery

compartment for storage.

or visit: www.fzspray.com/pages/

operation-guides

– 4 –

© WESSOL, LLC
REGISTER YOUR SPRAYER!
To take advantage of the 1-year Limited Warranty from WESSOL, LLC. Register your sprayer at the website below:
fzspray.com/pages/register
Please read and follow this manual carefully to ensure that you get the most out of your new sprayer. If you need assistance with the assembly or operation of your sprayer, please don’t hesitate to contact WESSOL via the support methods below: fzspray.com spraysquad@fzspray.com

ZEPHYR OPERATION GUIDE FZSATJ-3

! THE BATTERY
These batteries have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries
especially when wearing rings or jewelry could result in serious burns.
· Recharge only with the charger specified by FlowZone®. A charger that is suitable for one type of battery pack may create a risk of fire when used with another batter pack.
· Only use sprayers specifically
designated with their designated battery packs. Use of any other battery packs may create a risk of injury and fire. · When battery pack is not in use, keep it away from other metal objects,
like paper clips, coins, keys, nails, screws or other small metal objects,
that can make a connection from
one terminal to another. Shorting the battery terminals together may cause burns or fires. · Under abusive conditions, liquid can be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. · Liquid ejected from the battery may cause irritation or burns. · Do not use a battery pack or sprayer that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. · Do not expose a battery pack or sprayer to fire or excessive temperature. Exposure to fire or temperature above 265°F (130°C) may cause explosion. · Follow all charging instructions and do not charge the battery pack outside the temperature range specified in the instructions. Charging improperly or at a temperature outside the specified range may damage the battery and increase the risk of fire.
STORING BATTERY PACK
LONGER THAN 30 DAYS
· Store the battery pack where the temperature is below 80°F and away from moisture.
· For long-term storage, regular charging of the battery is required

to maximize battery life. Check the battery level using the indicator lights every 4 weeks. Recharge the battery if it falls below 3 bars. · Do not allow the battery to fully discharge.
BATTERY RECYCLING
PREPARATION
· To preserve natural resources, please recycle or dispose of the batteries properly.
· This product contains Lithium-ion batteries. Local, state or federal laws may prohibit disposal of lithium-ion batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and/or disposal options.
LITHIUM-ION BATTERY PACKS
· Lithium-ion batteries deliver fade free power for their entire run time. Lithium-ion batteries will not gradually lose power due to decreasing battery charge.

Instead, power form the battery pack will drop from full to zero once the full charge has been drained from the battery. Once this happens, recharging of the battery is required.
BATTERY PACK PROTECTION FEATURES
· Lithium-ion battery packs are designed with features that protect the lithium-ion cells and maximize battery life. If the sprayer stops during use, release the trigger to reset and resume operation. If the sprayer still doesn’t work, the battery needs to be recharged.
If after 2 hours during the charging process, none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the product. DO NOT insert another battery. Contact Customer Support for instructions on replacing the battery.

– 5 –

ZEPHYR OPERATION GUIDE FZSATJ-3

CONTENTS:

ABOUT 07 Specifications 08 What’s Inside 09 Parts Diagram
SET UP 10 Sprayer Assembly 12 How to Spray 15 Aftercare
TROUBLESHOOT 17 Common Solutions 19 Parts & Accessories 21 Warranty

TOOL ONLY 23 QuickSwapTM Adapter Installation 24 Tool Only Parts Diagram

– 6 –

ZEPHYR OPERATION GUIDE FZSATJ-3
WHAT ARE THE CAPABILITIES OF YOUR SPRAYER?
This FlowZone® sprayer is a highly efficient sprayer that is suitable for spraying many kinds of chemicals and solutions.
Powered by a 18V Lithium-ion battery, this sprayer results in more efficiency than a manual sprayer. This sprayer can be operated continuously for up to 2 hours and spray more than 24 gallons per battery charge at a distance of over 25 feet!

FlowZone® ZephyrTM Specifications

Model Number

FZSATJ-3

Pump Type

Battery Type

Lithium-ion

Battery Voltage

18V

Battery Capacity

2.6Ah

Battery Charging Time 1 hour

Battery Cycle Life

1,000 cycles

Battery Charger

21V/1A

Spray Time Pressure Spray Distance Tank Capacity Flow Rate Pump Life

Standard diaphragm Up to 2 hours Up to 40 psi >20 feet 4 gallon 0.2 gal/min 500 hours

– 7 –

ZEPHYR OPERATION GUIDE FZSATJ-3
1
2

5 8

15 16

W H AT ‘ S
INSIDE
For part numbers and replacement parts/accessories please see pages 9 & 19.

Name

1 Tank Lid

2 4-Gallon Tank

3 Tank Strainer

4 Top Holster 5 Bottom Holster 6 Nuts & Bolts

Name

7 18V/2.6Ah Battery Pack

8 21V/1A Battery Charger

9 Carbon Fiber Spray Wand

10 Inline Spray Handle 11 Backpack Straps

12 UV-Resistant 5-Foot Hose

Name

13 80° Fan Nozzle

14 0° Pin Stream Nozzle

15 45° Fan Nozzle

16 Adjustable Nozzle

– 8 –

SPRAYER DIAGRAM & Replacement Parts

ZEPHYR OPERATION GUIDE FZSATJ-3

FZRARV

Tank Lid with Wand Holster

FZRABW

Tank Strainer

FZRAMZ

4-Gallon Tank

FZRANL

Upper Wand Holster

FZRANK

Lower Wand Holster

FZRATL

Pump

FZRAOG

Pump Outlet Hose & Nut

FZRAGK

Pump Inlet Filter

FZAATA

FlowZone Battery Adapter

FZRAEG

Battery Door Assembly

FZAAEN

18V/2.6Ah Battery

FZAAEL

21V/1A Charger

45° Fan Tip w/ 45° Base Assembly

Adjustable Cone w/ 45° Base Assembly

FZRASV

0° Pin Stream Nozzle Tip

80° Fan Nozzle Tip

FZRAQX-V1

Inline Spray Handle

FZRADK

18-in. Carbon Fiber Wand

FZRAOF

5-ft. UV-Resistant Hose

FZRATK

Backpack Straps

FZRATM

Front Cover Plate

13 14

18 19

11 1
17
4 2
5

6
21 3

– 9 –

8 7

ZEPHYR OPERATION GUIDE FZSATJ-3
GETTING STARTED
Setting up your sprayer
NOTE: The sprayer may have residual water in it when first opened. This is due to quality testing every sprayer undergoes before leaving our factory.

Take off the tank lid (1). Lay the sprayer flat. Bring the backpack

Remove the nuts and bolts straps (11) to the bottom of the tank and

(6), and holsters (4, 5) from insert through designated opening. Once

the tank strainer (3). Remove inserted, tilt the buckle upward, insert

the nozzles (13, 14, 15, 16) on the underside of the buckle & pull

from the battery holster. through. Next, insert through the top side

Set aside.

of the buckle and pull through.

3 A

Next, slide the adjustable strap through the top tank loop. Continue by sliding the strap under and over the buckle fitting. Lightly tug to make sure the strap is secure. Repeat on other side.
– 10 –

ZEPHYR OPERATION GUIDE FZSATJ-3
4

5
A

If the shoulder straps
arrive detached, attach the bottom to the adjustable buckle using the same method as before.

Slide the top wand holster
onto protruding holster
mount on the sprayer tank.
Insert a nut on one side of the hexagonal slot on the bottom
of the holster and screw the bolt through the other
side using a Phillip’s head screwdriver until the bolt
fastens into the nut. Repeat for the bottom holster/slot.

Take the inline spray handle
(10) and attach it to the threaded fitting on the end
of the hose (12). Tighten the fitting to ensure the
gasket properly seals the
connection.

If spraying with the carbon fiber spray wand (9), thread
either end of the wand
to the spray handle male
threads. Make sure the o-ring sits flush with the
threads, and then twist the
cap into place.

– 11 –

ZEPHYR OPERATION GUIDE FZSATJ-3
S P R AY I N G
Preparing to spray

Although the battery (7) may be partially charged upon delivery, it is essential to fully charge the battery prior to the first operation. An indicator light should flash while the battery is plugged in and charging.
The charge level can be viewed by activating the indicator lights on the battery by pressing on the battery icon.

In a separate container,

prepare the solution

you wish to spray

according

the

chemical manufacturer’s

instructions. Remove the

tank lid and carefully pour

the solution through the

tank strainer. Securely

tighten the tank lid.

When using chemicals, always wear protective clothing, including respiratory protection masks, gloves, eye protection, etc.

– 12 –

ZEPHYR OPERATION GUIDE FZSATJ-3
3

Determine the nozzle you
would like to use and place it onto the carbon fiber wand. Bring the turqouise o-ring to sit flush with the nozzle base. Once in place, bring the cap to the nozzle base and thread it to secure the nozzle. General flow rates for each nozzle can be
found on page 14.

Turn the pump on by flipping the toggle switch to ON. Reference flow rate and spraying pressure chart on Page 14.
5

© WESSOL, LLC
Priming your sprayer
NOTE: Although rare, when spraying for the first time or after storing the sprayer for an extended amount of time, the sprayer may need help priming. If the sprayer turns on and you can hear the pump running, but no liquid is passing through the sprayer, you will need to manually prime the sprayer according to the steps below:
1. With the sprayer off, install the battery and make sure the battery cover is shut.
2. Remove the tank lid and take the tank strainer out to reveal the inside of your sprayer tank.
3. Locate the inlet filter at the bottom of the sprayer tank (See diagram 3 on page 18 for a visual representation). Gently wiggle the white circular piece until it comes apart from the inlet tube. Set aside.
4. Using a garden hose or similar delivery method, rapidly run clean water into the inlet tube where the mesh filter was. Turn your sprayer on at full power (speed 5). Squeeze the trigger until water comes out.
5. Reinstall the inlet filter with the mesh screen facing the bottom of the tank.

To begin spraying, simply hold down the trigger on the spray gun.
– 13 –

Scan for video instructions or visit https://fzspray.com/pages/ troubleshoot#priming-sprayer

ZEPHYR OPERATION GUIDE FZSATJ-3

NOZZLE FLOW RATES

Nozzle Tips:
45° Fan Nozzle 80° Fan Nozzle 0° Pin Stream Nozzle
Adjustable Nozzle

Cone Stream

Flow Rate:
0.2 gpm 0.2 gpm 0.3 gpm 0.2 gpm 0.3 gpm

Pressure:
40 psi 40 psi 10 psi 40 psi 10 psi

NOTE

The included nozzles are engineered for a low flow rate. These nozzles are only compatible with the ZephyrTM,
and will cause damage to the pumps if used on other FlowZone Series 2.5 / 3 sprayers.

– 14 –

ZEPHYR OPERATION GUIDE FZSATJ-3

AFTERCARE
Sprayer maintenance
CAUTION: Failure to properly rinse out the sprayer may cause chemical residue build-up that can clog or damage internal and external components. Leaving chemical liquids in the sprayer when not in use can lead to premature wear and voiding of the warranty. Never store the sprayer with chemical inside.
1. With the sprayer off, dispose of extra product based
on the manufacturer’s instructions. Rinse out any
residual solution in the spray tank with warm soapy
water. Then, spray fresh water through the sprayer for
3-5 minutes to clear the sprayer of chemicals.
2. Disconnect the spray gun from the hose and allow the hose to hang down towards the ground; draining the
hose of liquid. 3. Throughly dry the sprayer tank and clear the nozzles
and inlet filter of any build-up.
4. Store the sprayer in a dry, clean, and shaded place to
protect it from extreme heat or frost.

NOTE

For long-term storage, regular charging of the battery is required to maximize battery life. Check the battery
level using the indicator lights every 4 weeks. Recharge the battery if it falls below 3 bars. Do not allow the battery to fully discharge.

© WESSOL, LLC
Cleaning the inlet filter
NOTE: It is recommended you clean your inlet filter at least every other time your sprayer is used. Buildup at the inlet filter can cause damage to the pump and reduce spraying pressure.
1. With the sprayer off and battery removed, take off the tank lid.
2. Lift the tank strainer out of the mouth of the sprayer tank and set aside.
3. Reach into the sprayer tank and gently pry the inlet filter from the pump connection at the bottom of the tank.
4. Rinse the inlet filter with fresh water and get rid of any debris or particles.
5. Taking a clean cloth, wipe down the filter screen and dry the inlet filter. Reassemble the sprayer with the inlet filter and store the unit in protected area.

– 15 –

ZEPHYR OPERATION GUIDE FZSATJ-3

– 16 –

ZEPHYR OPERATION GUIDE FZSATJ-3

TROUBLESHOOTING
If your sprayer is not turning on or functioning as it should, visit fzspray.com/pages/troubleshoot for detailed instructions on how to properly determine the cause of the issue.
To contact Technical Support, email support@wessol.com or call +1 803-339-2500.

Problem Sprayer does not turn on. Leaks from tank.
Leaks from gun/nozzle. Clogged pump / hose / gun / wand / nozzle

Possible Cause(s) Dead battery
Defective or damaged part

Solution
Charge the battery. If the battery will not charge, test the charger or contact Support for a replacement if applicable.
Follow the instructions at fzspray.com/troubleshoot or contact Support for guidance.

Loose hose connection

Remove the plastic cover plate and locate the hose connection to the pump. Tighten the hose clamp.

Loose hose connection

Ensure the spray gun is fully tightened onto the threaded end of the hose.

Missing or worn gasket

Locate the necessary part from page 19 and contact Support or visit fzspray.com to purchase.

Not rinsing parts with water Take apart and thoroughly clean the parts. Rinse the sprayer with warm,

after use.

soapy water after each use.

– 17 –

ZEPHYR OPERATION GUIDE FZSATJ-3

Problem
Dead battery.
Pump makes a sound when sprayer is on, but output is limited.

Possible Cause(s) Defective charger
Damaged Lithium-Ion cells Clog in filter or nozzle Clog in the pump

Solution
If the LED indicator lights do not turn on or only one red LED is on after being on the charger for over 2 hours, test the charger with a multimeter. Replace if necessary.
If the battery receives no reading from a multimeter, a replacement battery is needed.
Check parts for a clog. Using warm water, thoroughly clean the components.
Remove the plastic cover plate and locate the pump. Remove then open the pump and clean out debris. Contact Support for assistance.

– 18 –

ACCESSORIES & PARTS Included with Zephyr

ZEPHYR OPERATION GUIDE FZSATJ-3

FZRAMZ 4-Gallon Tank
FZZAZ BFZacRkApTaKck sBtarcakppsack Straps
FZRARV Tank Lid with Wand Holster
FBFBaZZatZcRtkAeAprZEyaGDcokor sCtorvaeprs

FZRANK Bottom Wand Holster
FBFInZZaliZcRnkeAApZSQapXcr-akVy 1 sHtarnadples
FZRADK Carbon Fiber Wand with Threaded Outlet (M18)
FZZAZ BFZacRkApSaVck sStprraapysNozzle Kit

FZAAEN 18V/2.6Ah Battery
FZZAZ FBZacAkApEaPck 2s1tVra/1pAsCharger
FZAATA FlowZone QuickSwapTM Battery Adapter
FZRATM Front Cover Plate

FZRANL Top Wand Holster

FZRAOF 5-Ft Hose

FZRATL Diaphragm Pump

Accessories and replacement parts can be purchased at your preferred distributor or online at fzspray.com.
– 19 –

ACCESSORIES & PARTS For purchase separately

ZEPHYR OPERATION GUIDE FZSATJ-3

FZAATB DeWalt®/Milwaukee® QuickSwapTM Battery Adapter
FZAATC Makita QuickSwapTM Battery Adapter
FZAATD Bosch QuickSwapTM Battery Adapter
FZAAQL Telescoping Pole Hip Holster

FZAADA 20-Ft. Extension Hose
FBF2Za-ZNZcAkoAApzZzQaleYckBoom sAtsrsaepms bly
FZAAQZ 4-Nozzle Boom Assembly
FZZAZ BFZacAkApMaOck sNtorzazplesHolster

FZAANS Mounted Sprayer Rack
FBF4Za-ZGZcAakAAlplZoMancLk sStprarapyser Cover
FZAANE Wand/Nozzle Flashlight Mount
FZZAZ BFZacAkApBaCck sHteraavpysDuty Trolley

FZAANY 16-ft. Telescoping Pole

FZAAOQ Pistol Grip Gun w/ Carbon Fiber Wand
& 110° Fan

FZAAMP TeeJet Nozzle Assembly PVC
Gaskets

Accessories and replacement parts can be purchased at your preferred distributor or online at fzspray.com.

– 20 –

ZEPHYR OPERATION GUIDE FZSATJ-3

WARRANTY
WARRANTY COVERAGE WESSOL, LLC warrants to the original purchaser that the FlowZone® product will function as intended under normal use and consistent maintenance, subject to certain limitations and exclusions. At the discretion of WESSOL, LLC, we will repair or replace any parts found to be defective in material or workmanship without charge, apart from shipping and handling costs, during the covered warranty period.
WARRANTY PERIOD The warranty period will begin from the date of retail purchase and exist for one (1) year, regardless of when the unit is placed in service. The warranty period is not extended if we opt to repair or replace the product in question.
WARRANTY CLAIMS WESSOL, LLC reserves the right to require the return of the defective product, proof of purchase, and established product registration to file a claim under this warranty.
PRODUCT REGISTRATION All sprayers purchased from FlowZone® or an authorized distributor must be registered online to validate the warranty and allow for warranty claim processing. Sprayers can be registered at fzspray.com/pages/register.
To activate the warranty on your sprayer, register it at fzspray.com/ register. If the product fails to function as intended DO NOT RETURN IT TO THE STORE. To view the complete warranty or submit a claim, visit fzspray.com/warranty.
– 21 –

ZEPHYR OPERATION GUIDE FZSATJ-3

EXCLUSIONS AND LIMITATIONS
WESSOL, LLC only warrants products purchased from authorized distributors. Products purchased from unauthorized resellers or distributors are not subject to warranty services.
The limited warranty does not cover damages, loss, or injury resulting from transportation, storage, accident, improper use, neglect, modifications, normal wear, or operation not in accordance with the instruction manual. WESSOL, LLC reserves the right to change the design or specifications of any product without obligation to modify previously produced units.
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR CONSUMER USE, ARE LIMITED TO THE DURATION SPECIFIED ABOVE. WESSOL, LLC’S LIABILITY IS LIMITED SOLELY TO THE REPAIR OR REPLACEMENT OF THE NON-FUNCTIONING PRODUCT OR PART. WESSOL, LLC EXCLUDES LIABILITY UNDER THIS WARRANTY FOR ANY AND ALL INCIDENTAL AND CONSEQUENTIAL LOSS OR DAMAGE.
In no event shall WESSOL, LLC be liable for any incidental, special, consequential or punitive damages, or for any costs, attorney fees, expenses, losses or delays alleged to be as a consequence of any damage to, failure of, or defect in any product including, but not limited to, any claims for loss of profits.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary from state to state.

– 22 –

ZEPHYR TOOL ONLY OPERATION GUIDE FZSATJ-3TO
1

Tools Needed: Phillips head screwdriver, pliers

Q U I C K S WA P TM
ADAPTER INSTALL ATION
Installing your preferred battery adapter*

TOOL ONLY SPECIFICATIONS

Model Number

FZSATJ-3TO

Adapter Battery Voltage

18V / 20V

Adapter Max Battery Ah

6Ah

Adapter Types

FlowZone®, Milwaukee® / DeWalt®, Makita®, Bosch®

*Skip this step if you’re using a FlowZone battery

If using a 3rd party battery adapter, loosen the 4 bolts
and remove the FlowZone
adapter with a Phillip’s head
screwdriver.

To detach the black (-) and red (+) wires, slide the rubber
protector off. Using pliers, press on the small tab above
the connector and pull.

Choose your preferred battery adapter and gather the x4 included bolts.

Align the adapter of choice with the holster slot. Slide the red (+) and black (-) wire connectors into the designated slot using pliers. Slide the rubber protectors back onto the
connection points.

Place excess wire back
inside the sprayer and tighten the 4 bolts using a
Phillip’s head screwdriver.

– 23 –

SPRAYER DIAGRAM & Replacement Parts

ZEPHYR TOOL ONLY OPERATION GUIDE FZSATJ-3TO

TOOL ONLY VERSION
FZSATJ-3TO

FZRARV

Tank Lid with Wand Holster

FZRABW

Tank Strainer

FZRAMZ

4-Gallon Tank

18 14

FZRANL

Upper Holster

FZRANK

Lower Holster

FZRATL

Pump

FZRAOG

Pump Outlet Hose & Nut

FZRAGK

Pump Inlet Filter

22 19

16 21

FZAATA

FlowZone QuickSwapTM Battery Adapter

FZAATB

DeWalt/Milwaukee QuickSwapTM Adapter

FZAATC

Makita QuickSwapTM Adapter

FZAATD

Bosch QuickSwapTM Adapter

45° Fan w/ 45° Base Assembly

Adjustable Cone w/ 45° Base Assembly

FZRASV

0° Pin Stream Nozzle Tip

80° Fan Nozzle Tip

FZRAQX-V1

Inline Spray Handle

FZRADK

18-in. Carbon Fiber Wand

FZRAOF

5-ft. UV-Resistant Hose

FZRATK

Backpack Straps

FZRAEG

Battery Door Assembly

FZRATM

Front Cover Plate

– 24 –

1 4
5
3

ZEPHYR OPERATION GUIDE FZSATJ-3

@FZSprayer

®
fzspray.com support@wessol.com

CONNECT WITH US:

/FZSpray

@FlowZoneSprayer
– 25 –

@flowzone_sprayer

Documents / Resources

ZEPHYR FZSATJ-3 Battery Sprayers [pdf] User Guide
FZSATJ-3 Battery Sprayers, FZSATJ-3, Battery Sprayers, Sprayers

References

User Manual

ZEPHYR FZSATJ-3 Battery Sprayers User Guide

FZSATJ-3 Battery Sprayers

Specifications:

Product Usage Instructions:

Preparation:

Operation:

Cleaning and Maintenance:

FAQ:

Q: Can I use essential oils with this sprayer?

Q: What should I do if the power switch is not functioning
correctly?

Q: How should I store the sprayer?

Documents / Resources

References

Leave a comment

Cancel reply