zencontrol zc-switch-c DALI-2 Switch Adapter Module Instruction Manual

This product must only be installed by a licensed electrician.
Before commencing installation, turn off and isolate the electrical supply. Do not attempt to service any part of the product as it will void the warranty. The switch must not be connected to any mains; it is powered directly from the DALI line. DALI is not SELV and should be treated as LV.

Installation

Remove the product from the box and inspect for damage. If damaged, return it for replacement.

Ensure safety warnings are followed.
Connect the two DALI terminals to the DALI line following wiring regulations.

Connect the switch to be adapted to the 5-pin output terminal.
Install the switch behind the wall-plate or mounting enclosure for a momentary switch.

Specifications

Product Range

Order code Description

zc-switch-c DALI-2 switch adapter, supports 1 button with indicator LED

Specifications

Supply voltage 9.5 – 22.5 V dc (supplied from DALI)
Control system DALI-2

Supply current 12 mA
Input 1 floating dry contact
- Note: Any switch used shall be LV rated
Output FELV supply voltage output,
- max. current 2 mA
Wiring 0.5 – 0.75 mm2
- Strip 6 – 7 mm
Operating temperature 0 to 45°C
Material PC
Ingress protection IP20

Safety information

This product must only be installed by a licensed electrician.
Before commencing installation turn off and isolate the electrical supply.
There are no user serviceable parts, attempting to service any part of the product will void the warranty
The switch must not be connected to any mains. It is powered directly from the DALI line.
DALI is not SELV and as such should be treated as LV.
As the installer, it is your responsibility to ensure you comply to all relevant building and safety codes. Refer to application standards for the relevant rules.
When the installation is complete, leave this manual with the building’s owner for future reference.
The installer must protect against accidental contact, all terminals are not safe to touch.
There is no isolation between the control terminals and supply. Outputs should be treated as LV.

Dimensions

Dimensions 40 / 20 / 10.5 mm

System Overview

Installation

Remove the product from the box and inspect it for any damage. If you believe the product to be damaged or otherwise unsound, do not install the product. Please pack it back into its box and return it to the place of purchase for replacement.

If the product is satisfactory, proceed with the installation:

Ensure safety warnings are adhered to.
Connect the two DALI terminals to the DALI line ensuring wiring regulations are followed. DALI is not polarised. DALI is not SELV and as such must be treated as LV. Do not connect the switch to any mains voltages.

Connect the switch to be adapted to the 5 pin output terminal.
Install switch behind the wall-plate or mounting enclosure for momentary switch. Note default configuration is A/B input. Configuration dependant on DALI-2 application controller.

Wiring diagram

Input / output configuration

Wire preparation

Notice

For more information on compliant software see our website zencontrol.com

FAQ

Q: Can I connect the switch adapter module to mains voltage?
- A: No, the switch must not be connected to any mains voltage; it is powered directly from the DALI line.
Q: What should I do if I believe the product is damaged?
- A: If you believe the product is damaged, do not install it. Please return it to the place of purchase for replacement.
Q: How should I configure the switch adapter for different applications?
- A: The default configuration is A/B input. Configuration depends on the DALI-2 application controller.

Information is subject to change without notice, E&OE

Documents / Resources

zencontrol zc-switch-c DALI-2 Switch Adapter Module [pdf] Instruction Manual
zc-switch-c DALI-2 Switch Adapter Module, zc-switch-c, DALI-2 Switch Adapter Module, Switch Adapter Module, Adapter Module, Module

References

User Manual

zencontrol zc-switch-c DALI-2 Switch Adapter Module

Product Usage Instructions