TC530R RFID Touch Computer
“
Product Information
Specifications:
- Model: TC530R-RFID Touch Computer
- Front Camera: 8MP
- Display: 6-inch LCD touch screen
- Features: RFID functionality, VoIP capabilities
Product Usage Instructions
Features Overview:
The TC530R-RFID Touch Computer is equipped with various features
including a front camera for photos and videos, a scan LED for data
capture status, a proximity/light sensor for display control, and
more.
Getting Started:
- Press and hold the power button to turn the device on or
off. - Use the front camera for capturing photos and videos.
- Utilize the scan button to initiate data capture.
- Adjust audio volume using the volume up/down button.
Additional Functions:
The device supports Voice over Internet Protocol (VoIP) calls.
Remember that RFID power will be disabled when using the device for
VoIP calls near the head, except for hands-free or wireless VoIP
calls.
FAQ
Q: What should I do if the device does not power on?
A: Make sure the battery is charged and try pressing and holding
the power button for a few seconds to turn it on.
Q: How do I capture data using the device?
A: Press the scan button to initiate data capture. Ensure the
scan LED indicates successful data capture.
“`
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530RRFID Touch Computer
Quick Start Guide
MN-004898-01EN Rev A
Copyright
2024/02/06
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2023 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of those agreements.
For further information regarding legal and proprietary statements, please go to:
SOFTWARE: zebra.com/linkoslegal. COPYRIGHTS: zebra.com/copyright. PATENTS: ip.zebra.com. WARRANTY: zebra.com/warranty. END USER LICENSE AGREEMENT: zebra.com/eula.
Terms of Use
Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries (“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies.
Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice.
Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.
Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
Features
This section lists the features of the TC53e-RFID touch computer. The TC53e-RFID features a built-in encoder/reader, including: · RFID tag read range of 1.5 – 2.0 m. · RFID read speed of 20 tags per second. · An omnidirectional antenna.
NOTE: When using the device for Voice over Internet Protocol (VoIP) calls near the head (for example, the user is holding the device to their ear), RFID power will be disabled. Hands-free or wireless VoIP calls (for example, with earphones or Bluetooth) will not disable RFID power.
Figure 1 Front and Side Views
2
3 45
1
10
9
6
7
8 3
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
Table 1 TC53e-RFID Front and Side Items
Number
Item
Description
1
Front camera
Takes photos and videos.
(8MP)
2
Scan LED
Indicates data capture status.
3
Receiver
Use for audio playback in Handset mode.
4
Proximity/light
Determines proximity and ambient light for controlling display backlight
sensor
intensity.
5
Battery status LED Indicates battery charging status while charging and application-generated
notifications.
6, 9 Scan button
Initiates data capture (programmable).
7
Volume up/down Increase and decrease audio volume (programmable).
button
8
6 in. LCD touch
Displays all information needed to operate the device.
screen
10
PTT button
Typically used for PTT communications.
4
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
Figure 2 Back, Top, and Bottom View
2
13 14
3
4
1 12
5
11
6
7 8
10
9
Table 2 TC53e-RFID Back, Top, and Bottom Items
Number
Item
Description
1
Power button Turns the display on and off. Press and hold to power off, restart, or lock the
device.
2, 4, 9 Microphone
Use for communications in Handset/Handsfree mode, audio recording, and noise cancellation.
3
Back common I/ Provides host communications, audio, and device charging via cables and
O 8 pins
accessories.
5
Battery release Pinch both latches in and lift up to remove the battery.
latches
6
Battery
Provides power to the device.
7
Speaker
Provides audio output for video and music playback. Provides audio in speakerphone mode.
8
DC input pins Power/ground for charging (5V through 9V).
5
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
Table 2 TC53e-RFID Back, Top, and Bottom Items (Continued)
Number
Item
Description
10
USB Type C
Provides power to the device using an I/O USB-C interface with 2 charge
and 2 charge pins.
pins
11
Hand strap
Attachment points for the hand strap.
attachment
points
12
Rear camera
Takes photos and videos with flash to provide illumination for the camera.
(16MP) with
flash
13
Exit window
Provides data capture using the imager.
14
UHF RFID
Integrated RFID.
NOTE: If an RFD40 or RFD90 sled is connected to the device, it overrides the integrated RFID.
123RFID Mobile Application
123RFID Mobile Application (app) for Android demonstrates the device’s tag operation functionality. This app is available on the Google Play store. For more information on installing the 123RFID Mobile app, go to the Zebra 123RFID Mobile Support page.
Installing a MicroSD Card
This section describes how to install a MicroSD card.
CAUTION–ESD: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the MicroSD card. Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring the operator is properly grounded. 1. Lift the access door.
6
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
2. Slide the microSD card holder to the Open position.
3. Lift the microSD card holder door.
4. Insert the microSD card into the card holder. Ensure that the card slides into the holding tabs on each side of the door.
5. Close the microSD card holder.
7
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
6. Slide the microSD card holder to the Lock position.
NOTE: The access door must be replaced and securely seated to ensure proper device sealing. 7. Reinstall the access door.
Installing the Battery
This section describes how to install a battery into the device. NOTE: Do not put any labels, asset tags, engravings, stickers, or other objects in the battery well. Doing so may compromise the intended performance of the device or accessories. Performance levels, such as sealing [Ingress Protection (IP)], impact performance (drop and tumble), functionality, or temperature resistance, could be affected. 1. Insert the battery, bottom first, into the battery compartment in the back of the device.
8
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
2. Press the battery down until it snaps into place.
Using the Rechargeable Li-Ion Battery with BLE Beacon
This device utilizes a rechargeable Li-Ion battery to facilitate Bluetooth Low Energy (BLE) Beacon. When enabled, the battery transmits a BLE signal for up to seven days while the device is powered off due to battery depletion.
NOTE: The device transmits a Bluetooth beacon only when it is powered off or in airplane mode.
For additional information on configuring the Secondary BLE settings, see techdocs.zebra.com/emdk-forandroid/13-0/mx/beaconmgr/.
Charging the Device
Before using the device for the first time, charge the main battery until the green LED Charging/Notification remains lit. To charge the device, use a cable or a cradle with the appropriate power supply.
To achieve optimal charging results, use only Zebra charging accessories and batteries. Charge batteries at room temperature with the device in sleep mode.
A standard battery charges from fully depleted to 90% in approximately 2 hours and from fully depleted to 100% in approximately 3 hours. In many cases, a 90% charge provides enough charge for daily use. Depending on the usage profile, a full 100% charge may last for approximately 14 hours of use.
The device or accessory always performs battery charging in a safe and intelligent manner. The device or accessory indicates when charging is disabled due to abnormal temperatures via its LED, and a notification appears on the device display.
Temperature 20 to 45°C (68 to 113°F)
Battery Charging Behavior Optimal charging range.
0 to 20°C (32 to 68°F) 45 to 50°C (113 to 122°F)
Charging slows to optimize the JEITA requirements of the cell.
Below 0°C (32°F) Above 50°C (122°F)
Charging stops.
9
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
Temperature Above 55°C (131°F)
Battery Charging Behavior The device shuts down.
To charge the main battery:
1. Connect the charging accessory to the appropriate power source.
2. Insert the device into a cradle or attach to a powered cable (minimum 9 volts / 2 amps). The device turns on and begins charging. The Charging/Notification LED blinks amber while charging, then turns solid green when fully charged.
Charging Indicators
The charging/notification LED indicates the charging status.
Table 3 Charging/Notification LED Charging Indicators
State
LED Color
Indications
Off
The device is not charging.
· The device is not inserted correctly in the cradle or connected to a power source.
· The charger/cradle is not powered.
Slow Blinking Amber (1 blink every 4 seconds)
Slow Blinking Red (1 blink every 4 seconds)
Solid Green
The device is charging. The device is charging, but the battery is at the end of its useful life. Charging is complete.
Solid Red Fast Blinking Amber (2 blinks/second)
Fast Blinking Red (2 blinks/second)
Charging is complete, but the battery is at the end of its useful life.
Charging error. For example: · Temperature is too low or too high.
· Charging has gone on too long without completion (typically 12 hours).
Charging error, and the battery is at the end of its useful life. For example: · The temperature is too low or too high.
· Charging has gone on too long without completion (typically 12 hours).
10
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
Charging the Spare Battery
This section provides information on charging a spare battery. To achieve optimal charging results, use only Zebra charging accessories and batteries. 1. Insert a spare battery into the spare battery slot.
Figure 3 Example of a 4-Slot Battery Charger
1
2. Ensure the batter is seated properly.
The Spare Battery Charging LED (1) blinks, indicating charging.
The battery charges from fully depleted to 90% in approximately 2.5 hours and from fully depleted to 100% in approximately 3.5 hours. In many cases, the 90% charge provides plenty of charge for daily use. Depending on the usage profile, a full 100% charge may last for approximately 14 hours of use.
Accessories for Charging
Use one of the following accessories to charge the device and/or spare battery.
Charging and Communication Description
1-Slot Charge Only Cradle 1-Slot USB/Ethernet Cradle 5-Slot Charge Only Cradle with Battery 5-Slot Charge Only Cradle
Part Number
CRD-NGTC5-2SC1B CRD-NGTC5-2SE1B CRD-NGTC5-5SC4B CRD-NGTC5-5SC5D
Charging
Battery (In
device)
Spare Battery
Yes
Yes
Yes
Yes
Yes
Yes
Communication
USB
Ethernet
No No Yes Yes No No
Yes
No
No No
11
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
Description
5-Slot Ethernet Cradle Charge/USB Cable
Part Number
CRD-NGTC5-5SE5D CBL-TC5X USBC2A-01
Charging
Battery (In
device)
Spare Battery
Yes
No
Yes
No
Communication
USB
Ethernet
No Yes Yes No
1-Slot Charge Only Cradle
This USB cradle provides power and host communications.
1
AC line cord
2
Power supply
3
DC line cord
4
Device charging slot
5
Power LED
6
Spare battery charging slot
12
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
1-Slot Ethernet USB Charge Cradle
This Ethernet cradle provides power and host communications.
1
AC line cord
2
Power supply
3
DC line cord
4
Device charging slot
5
Power LED
6
Spare battery charging slot
7
DC line cord input
8
Ethernet port (on USB to Ethernet module kit)
9
USB to Ethernet module kit
10
USB port (on USB to Ethernet module kit)
NOTE: The USB to Ethernet module kit (KT-TC51-ETH1-01) connects via a single-slot USB charger.
5-Slot Charge Only Cradle
The 5-Slot Charge Only Cradle: · Provides 5.0 VDC power for operating the device.
13
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
· Simultaneously charges up to five devices or up to four devices and four batteries using the 4-slot battery charger adapter.
· Contains a cradle base and cups that can be configured for various charging requirements.
1
AC line cord
2
Power supply
3
DC line cord
4
Device charging slot with shim
5
Power LED
5-Slot Ethernet Cradle
The 5-Slot Ethernet Cradle: · Provides 5.0 VDC power for operating the device. · Connects up to five devices to an Ethernet network. · Simultaneously charges up to five devices or up to four devices and four batteries using the 4-slot
battery charger adapter.
14
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
1
AC line cord
2
Power supply
3
DC line cord
4
Device charging slot
5
1000Base-T LED
6
10/100Base-T LED
5-Slot (4 Device/4 Spare Battery) Charge Only Cradle with Battery Charger
The 5-Slot Charge Only Cradle: · Provides 5.0 VDC power for operating the device. · Simultaneously charges up to four devices and four spare batteries.
15
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
1
AC line cord
2
Power supply
3
DC line cord
4
Device charging slot with shim
5
Spare battery charging slot
6
Spare battery charging LED
7
Power LED
16
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide Charge/USB-C Cable
The USB-C Cable snaps onto the bottom of the device and removes easily when not in use. When attached to the device, it provides charging and allows the device to transfer data to a host computer.
Scanning with Internal Imager
Use the internal imager to capture barcode data. To read a barcode or QR code, a scan-enabled application is required. The device contains the DataWedge Demonstration (DWDemo) app, which allows you to enable the imager, decode the barcode/ QR code data, and display barcode content. NOTE: The SE4720 displays a red dot aimer. 1. Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
17
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
2. Point the exit window on the top of the device at a barcode or QR code.
3. Press and hold the scan button. The device projects the aiming pattern.
18
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
4. Ensure the barcode or QR code is within the area formed in the aiming pattern. Figure 4 SE4720 Aiming Pattern
Figure 5 SE4720 Picklist Mode Aiming Patterns with Multiple Barcodes
NOTE: When the device is in Picklist mode, it does not decode the barcode/QR code until the center of the crosshair touches the barcode/QR code.
The Data Capture LED light turns green, and the device beeps, by default, to indicate that the barcode or QR code was decoded successfully. 5. Release the scan button. The device displays the barcode or QR code data in the text field.
19
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
RFID Scanning Considerations
The following hand grips are recommended to ensure the RFID function works properly. RFID Scanning Orientation
Optimal Hand Grips IMPORTANT: When holding the device, ensure that your hand is below the hand strap (towel) bar and the scan buttons.
20
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
Ergonomic Considerations
21
DRAFT – INTERNAL USE ONLY – 2024-02-06Z
TC530R-RFID Touch Computer Quick Start Guide
Service Information
Repair services using Zebra-qualified parts are available for at least three years after the end of production and can be requested at zebra.com/support.
22
www.zebra.com
Documents / Resources
 |
ZEBRA TC530R RFID Touch Computer [pdf] User Guide TC530R, UZ7TC530R, TC530R RFID Touch Computer, RFID Touch Computer, Touch Computer, Computer |