ZEBRA FX7500 RFID Reader User Guide

ZEBRA FX7500 RFID Reader

Specifications

• Model: FX7500 RFID Reader
• Compliance: EPC Class1 Gen2
• Antenna Ports: 4
• Network Interface: 10/100 BaseT Ethernet Port (with POE)
• Power Input: 24 VDC

Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products.

Introduction

FX7500 Series readers provide real time, seamless tag processing for EPC Class1 Gen2 compliant tags. This Quick Start Guide provides information about installing and connecting the reader. For more information refer to the FX Series RFID Fixed Reader Integration Guide, available at: www.zebra.com/support.

Reader Installation

1. Unpack the reader.
2. Set up the reader and tags on a desktop.
3. Connect the antenna to antenna Port 1.
4. Connect the Ethernet cable to the Ethernet port.
   Connecting the reader to a subnet that supports DHCP is recommended. This installation procedure is not guaranteed to work if DHCP is disabled in the reader and if the reader is connected directly to a PC.
5. Connect the AC power supply to a power outlet and connect to the power port.

NOTE This step is not required for networks supporting Power-over-Ethernet (POE).
The green power LED remains lit after successfully powering up.

Connecting to the Reader

To connect via host name:

1. Open a browser. Refer to the FX Series RFID Fixed Reader Integration Guide for recommended browsers.
2. Enter the host name, provided on a label on the reader, in the browser (e.g., http://fx7500cd3b0d) and press Enter. The User Login window appears and the reader is ready.
   NOTE Connect the reader to a network that supports host name registration and lookup to ensure the network can access the reader using the host name. For instance, some networks can register host names through DHCP. When first connecting to the reader, it is recommended to keep DHCP enabled in both the PC and in the reader, although it is not guaranteed that host name will work all the time.
   If the host name label is missing, construct the host name using the reader MAC address on the bottom of the reader. To do this, enter the prefix FX7500, followed by the last six characters of the MAC address. For example, for a MAC address of 0023683BA63A, use the prefix FX7500, followed by 3BA63A.
   Enter http://FX75003BA63A in the browser address bar to access the reader. If the host name method does not work, refer to the section, Connecting to the Reader in the FX Series RFID Fixed Reader Integration Guide for other connection options.
3. If you are using a worldwide device, go to Configure Reader > Region to set the country in which you are using the device.

Additional Information

Following are links to additional information and software:
Product Manuals available at: www.zebra.com/support

• FX Series RFID Fixed Reader Integration Guide (p/n MN000026Axx)
• RFID Reader Software Interface Control Guide (p/n 72E-131718-xx)
• RFID Demo Applications User Guide (p/n 72E-160038-xx)
• Data Sheet: www.zebra.com/FX7500.
• PowerSession and other related software: www.zebra.com/support.

Regulatory Information

This provides information for the Zebra, FX series RFID Reader products, Regulatory Model No: FX7500. For information on setting up and using the reader, refer to the FX Series RFID Fixed Reader Integration Guide at www.zebra.com/support.
All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following website: www.zebra.com/support. Zebra devices must be professionally installed. The Radio Frequency Output Power will not exceed the maximum allowable limit for the country of operation. Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the authority to operate the equipment.

Antennas
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could cause damage and may violate regulations.

Health and Safety Recommendations

Warning for Use of Wireless Devices

• Please observe all warning notices with regard to the usage of wireless devices.

Potentially Hazardous Atmospheres
You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).

Safety in Hospitals
Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected.

Use With Hearing Aids
When some wireless devices are used near some hearing devices (hearing aids and cochlear implants), users may detect a buzzing, humming, or whining noise. Some hearing devices are more immune than others to this interference noise, and wireless devices also vary in the amount of interference they generate. In the event of interference you may want to consult your hearing aid supplier to discuss solutions.

Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device.

FCC / EU RF Exposure Guidelines

Safety Information

Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.

International
The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on “International” human exposure to electromagnetic fields refer to the Zebra Declaration of  Conformity (DoC) at www.zebra.com/doc. For further information on the safety of RF energy from wireless devices, see responsibility.zebra.com/index.php/downloads/, which is located under Wireless Communications and Health.

US and Canada
To comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop or similar configurations must operate with a minimum separation distance of 34 cm from all persons.

EU
To comply with EU RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop or similar configurations must operate with a minimum separation distance of 34 cm from all persons.

Power Supply
This device must be powered from an 802.3af or 802.3at compliant power source which has been certified by the appropriate agencies, or by a Zebra approved UL LISTED ITE (IEC/EN60950-1) power supply with electrical ratings: Output 24Vdc, min 3.25A, with a recommended ambient temperature of at least 40 degrees C. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous.

Air Handling Space Applications
This device is suitable for use in Environmental Air Handling Space (EAHS) in accordance with Section 300-22(c) of the National Electric Code, and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 21, CSA C22.1. All Cables intended for interconnecting the FX7500 to other devices shall be suitable rated for use in Environmental Air Handling Space per UL 2043. Devices such as Power Adapters, PoE (Power Injectors), antennas shall not be installed in the Environmental Air Handling Space unless they are suitable for use in the EAHS per UL 2043.

Wireless Devices Country Approvals

Regulatory markings, subject to certification, are applied to the device signifying the radio is approved for use in the following countries: United States, Canada, Japan, China, South Korea, Australia, and Europe1 Please refer to the Zebra Declaration of Conformity (DoC) for details of other country markings. This is available at www.zebra.com/doc.

• Operation of the device without regulatory approval is illegal.

Note1: Europe includes, Austria, Belgium, Bulgaria, Croatia, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Country Selection – Worldwide Version Only Select only the country in which you are using the device. Any other selection will make the operation of this device illegal.

Frequency of Operation – USA (FCC) and Canada
The range of channels is limited by firmware.

Radio Frequency Interference Requirements – FCC

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radio Frequency Interference Requirements – Canada

CAN ICES-3 (B)/NMB-3(B)
This Class B digital apparatus complies with Canadian ICES-003.

Radio Transmitters
This device is in compliance with the NRC for Industry Canada applicable to license-exempt radios. Use is allowed with the following two conditions: (1) the device must not produce interference, and (2) the device must accept any interference to the radio even if the interference is likely to compromise operation.

Label Marking: The Term “IC:” before the radio certification only signifies that Industry Canada technical specifications were met. In accordance with the regulations of Industry Canada, this radio transmitter can operate with an antenna of a type and a maximum gain (or lower) approved for the transmitter by Industry Canada. With the aim of reducing the risk of radio interference to other users, the chosen antenna type and its gain should be selected so that the equivalent isotopically radiated power (e.i.r.p.) does not exceed the intensity necessary for the establishment of a satisfactory connection.

The FX7500 has been approved by Industry Canada to operate with the antenna types listed below and having a maximum gain allowable and the impedance required for each type of antenna. The antenna types not included in this list, or whose gain is higher than the maximum gain indicated, are strictly prohibited for the operation of the transmitter.

Marking and European Economic Area (EEA)

Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with Directive 2011/65/EU and 1999/5/EC or 2014/53/EU (2014/53/EU supersedes 1999/5/EC from 13th June 2017). The full text of the EU Declaration of Conformity is available at the following internet address: www.zebra.com/doc.

Waste Electrical and Electronic Equipment (WEEE)