Yoosee 2A296-Y3 Network Camera
App installation
A. Scan the QR code below to download the APP “Yoosee”
B. Download and install “Yoosee” from Apple Store for IOS, and search on GooglePlay for Android.
Note: It is recommended to use the QR code scanning software that comes with your browser or a third party to scan and download App.
Connect camera
Step 1: Please charge the camera before connection.
- Use the output DC5V2A adapter to charge camera.
Charging: red LED Fully charged: LED OFF - Turn on the camera When the green indicator light is on, the camera is starting.
When the blue indicator light is on, the GW signal has been connected and the starting is completed. - Reset: Press and hold the restart button for 5-8 seconds, and the blue light turns off and resets successfully.
Note: If blue light stays off for two minutes, please charge camera.
Step 2:
- Register account
- Add camera
- Click “+” to add a new camera.
Jump to the following link operation interface. Please Click “add devices manually” to connect camera.
- Click “Next” .Enter the router account name and password
- Click “connect to GW WIFI” .Jump to the mobile wifi settings, search and click to connect to the “GW” hotspot signal.App is adding camera, which is expected to take 1-2 minutes. If the addition fails, please place the camera closer to the router and connect it again.
- APP announces the connection status, and the screen can be browsed after the connection is successful.
- Click “+” to add a new camera.
| is successful: | |
| Name: | Y-3 HD -WIFI/P2P network camera |
| Video resolution: | H.264 1920*1080 1280*720 |
| Video frame rate: | 30fps±1fps |
| Rotation Angle: | 360° horizontally |
| Infrared lamp: | Built-in matt f3-940 band 14miu low light |
| Sensors: | 1/3″Color CMOS |
| Antenna: | 802.11n WIFI Internal Antenna |
| Image proportion: | 4:3 |
| Charging voltage: | DC-5V-1.5A |
| Storage support | Micro SD Card(TF Card)Up to 128GB |
| Battery Type: | High capacity polymer lithium battery |
| Note: | TFcard to use the full capacity and high speed!! To remove the TF card turn off the camera first. |
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
The device has been evaluatec to meel general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Documents / Resources
 |
Yoosee 2A296-Y3 Network Camera [pdf] Instruction Manual 2A296-Y3, 2A296Y3, Y3, 2A296-Y3 Network Camera, 2A296-Y3, Network Camera, Camera |