LANCOM Systems ON-D8a Lancom AirLancer
Pariview of the mounting kit
- 1 connection flange (A)
- 1 connection arm (B)
- 1 pole flange / wall bracket (C)
- 4 washers M6 (D)
- 4 spring washers M6 (E)
- 4 nuts M6 (F)
- 1 pole clamp for pole diameter up to 62.5 mm (I)
- 2 hexagon head screws M8x35 (J)
- 4 spring washers M8 (K)
- 4 washers M8 (L)
- 2 nuts M8 (M)
- 2 hexagon head screws M8x70 (N)
Ko si ninu awọn dopin ti ifijiṣẹ
2 ẹgbẹ clamps for pole diameter > 62.5 mm (H)
Mounting the antenna flange and connection arm
Screw the connection flange (A) to the back of the antenna housing using the enclosed washers (D), spring washers (E), and nuts (F). Make sure that the spring washers (E) are located directly under the nuts (F).
Then fasten the connection arm (B) hand-tight to the connection flange (A) using a screw (J), a spring washer (K), a washer (L), and a nut (M). Make sure that the spring washer (L) is located directly under the screw head.
Igbaradi fun odi iṣagbesori
Ti o ba fẹ gbe eriali naa sori ogiri, lo òke ogiri (C) bi awoṣe liluho lati samisi awọn iho lu fun fifi sori odi.
Lu awọn ihò ti o baamu ni awọn isamisi ati fi awọn dowels (kii ṣe pẹlu) sinu wọn ti o ba jẹ dandan. Ti o da lori ohun elo ogiri ati ipo, ijinle ati iwọn ila opin ti awọn iho gbọdọ wa ni titunse.
Odi iṣagbesori ti eriali
- Sopọ mọ akọmọ ogiri pẹlu awọn ihò liluho ki o so pọ pẹlu awọn skru to dara.
- Now hand-tighten the connection arm (B) already mounted on the connection flange (A) to the wall bracket (C) using a screw (J), a spring washer (K), a washer (L), and a nut (M).
- Make sure that the spring washer (K) is located directly under the screw head and that the arrow on the back of the antenna housing is pointing upwards.
- Mu eriali naa pọ ni ibamu si awọn ifẹ rẹ ati lẹhinna Mu awọn skru ti apa asopọ pọ pẹlu iyipo to dara.
Polu iṣagbesori ti eriali
Position the pole flange (C) at the desired height on a suitable pole with sufficient load-bearing capacity. Use the pole clamp (I) to attach to poles up to 62.5 mm in diameter.
- Fasten the pole clamp (I) to the pole flange (C) using the two screws (N), the spring washers (K), and the washers (L). Please note that the mast clamp must be rotated depending on the mast diameter.
- For pole diameters over 62.5 mm, you need suitable band clamps (H) (not included in the scope of delivery) and guide them through the pole flange and around the pole as shown in the overview
and tighten them after you have aligned the pole flange.
- Then connect the pole flange (C) hand-tight to the connection arm (B) already mounted on the antenna using an enclosed screw (J), a spring washer (K), a washer (L), and a nut (M).
- Make sure that the spring washer (K) is located directly under the screw head and that the arrow on the back of the antenna housing is pointing upwards.
- Mu eriali naa pọ ni ibamu si awọn ibeere rẹ lẹhinna Mu awọn skru ti apa asopọ pọ pẹlu iyipo to dara.
Alaye pataki
- Lodidi mimu ti ga igbohunsafẹfẹ
Lati le ni ibamu pẹlu awọn ibeere aabo ti Ilana EU 2014/53 ati EN 62479 pẹlu awọn ihamọ ipilẹ fun aabo eniyan ni awọn aaye itanna ati “Ifihan FCC lori Ifihan eniyan si Awọn aaye itanna igbohunsafẹfẹ Redio”, o jẹ dandan lati tunto awọn ti o tọ eriali ere ni WLAN olulana tabi WLAN wiwọle ojuami. - Itanna ati Itanna Equipment Ìṣirò
Jọwọ maṣe sọ itanna ati egbin itanna nù sinu egbin ile, nibiti ko le tunlo. Rii daju pe itanna rẹ ati egbin itanna ti sọnu ni ibamu pẹlu awọn itọnisọna to wulo lọwọlọwọ ti orilẹ-ede rẹ. - Imudani ti o tọ ti awọn kebulu eriali
Awọn kebulu eriali jẹ awọn kebulu RF ifarabalẹ. Nigbati o ba gbe wọn silẹ, o ṣe pataki lati rii daju pe awọn kebulu naa ko ni kiki ati ti tẹ diẹ bi o ti ṣee, nitori eyi le ja si awọn adanu ni awọn ofin ti iṣẹ eriali. Bakanna, awọn kebulu eriali ko yẹ ki o ni ọgbẹ sinu awọn losiwajulosehin okun. - Ere eriali ati ifopinsi ti awọn ebute oko eriali ti ko lo lori awọn aaye wiwọle
Awọn asopọ eriali ti a ko lo lori aaye wiwọle gbọdọ wa ni fopin si pẹlu eriali ọpá paade. Fun awọn aaye wiwọle inu ile, resistor ifopinsi ti o wa pẹlu ohun ti nmu badọgba AirLancer AN-RPSMA-NJ le ṣee lo. Ni afikun, eriali ere gbọdọ wa ni pato ninu awọn iṣeto ni ti awọn wiwọle ojuami.
Imọ data
- Iwọn igbohunsafẹfẹ 4,900 - 5,900 MHz
Awọn abuda eriali
- Radiation patterns Horizontally: 8° Vertically: 8°
- Recommended use Point-to-Point
- VSWR 2.0:1 max.
- Gain 21 dBi max.
Data Mechanical
- Awọn iwọn (mm) 370 x 370 x 30 (W x H x D)
- Weight 1,800 g (Antenna without mounting kit)
- Iwọn iṣẹ ṣiṣe -40 ° C si 85 ° C
- Color Light grey
- Material UV resistant plastic
- Mounting options Wall- and pole mounting, alignable
- Cables & Connectors 2x 100 cm ULA100 cable with N-Plug connector
Nkan
- Atilẹyin ọja ọdun 2 fun AirLancer ati awọn ẹya ẹrọ
- Nkan no. 61708
- Scope of delivery Antenna, 2 connection cables, mounting kit for wall and pole mounting
Awọn ọna ṣiṣe LANCOM GmbH
A Rohde & Schwarz Company Adenauerst. 20/B2
52146 Wuerselen | Jẹmánì
info@lancom.de | lancom-systems.com
LANCOM, LANCOM Systems, LCOS, LANcommunity, LANCOM Service LANcare, LANCOM Redio Iṣakoso, ati AirLancer jẹ aami-išowo ti a forukọsilẹ. Gbogbo awọn orukọ miiran tabi awọn apejuwe ti a lo le jẹ aami-iṣowo tabi aami-iṣowo ti a forukọsilẹ ti awọn oniwun wọn. Iwe yii ni awọn alaye ti o jọmọ awọn ọja iwaju ati awọn abuda wọn. Awọn ọna LANCOM ni ẹtọ lati yi awọn wọnyi laisi akiyesi. Ko si gbese fun awọn aṣiṣe imọ-ẹrọ ati/tabi omis-
ions. 111436 09/2025
Awọn ibeere Nigbagbogbo
Q: Kini MO le ṣe ti diẹ ninu awọn ẹya ba sonu lati package?
A: Kan si atilẹyin alabara fun iranlọwọ ni gbigba awọn ẹya ti o padanu.
Q: How do I ensure proper alignment of the antenna during mounting?
A: Follow the provided instructions carefully and use appropriate tools to align the antenna as needed.
Awọn iwe aṣẹ / Awọn orisun
 |
LANCOM Systems ON-D8a Lancom AirLancer [pdf] Ilana itọnisọna ON-D8a Lancom AirLancer, ON-D8a, Lancom AirLancer, Lancom, AirLancer |