ESPRESSIF ESP32-C6-DevKitC-1 Development Board
ESP32-C6-DevKitC-1 v1.2
Awọn pato
- Modulu: ESP32-C6-WROOM1 tabi ESP32-C6WROOM-1U
- Awọn ẹya atilẹyin: Wi-Fi 6 (band 2.4 GHz), Bluetooth 5, IEEE 802.15.4 (Zigbee 3.0 ati Thread 1.3)
- Flash Memory: 8 MB SPI filasi
- Ipese Agbara: 5 V si 3.3 V LDO
- Ibudo USB: Ibamu USB Iru-C pẹlu USB 2.0 iyara ni kikun (iyara gbigbe 12 Mbps)
- Awọn pinni GPIO: Gbogbo awọn pinni GPIO ti o wa (ayafi fun ọkọ akero SPI fun filasi) ti fọ lati pin awọn akọle lori igbimọ
- LED: 3.3 V Agbara Lori LED
- Awọn bọtini: Bọtini Boot, Bọtini Tunto
- LED RGB: Adirẹsi RGB LED ti o wa nipasẹ GPIO8
Awọn ilana Lilo ọja
Ipilẹṣẹ Hardware Oṣo
- Ṣayẹwo ESP32-C6-DevKitC-1 fun eyikeyi ami ti ibaje.
- So ipese agbara pọ si ibudo USB Iru-C lori ọkọ.
Firmware ìmọlẹ
- Rii daju pe ESP32-C6-DevKitC-1 ti wa ni titan ati ti sopọ mọ kọmputa rẹ nipasẹ USB.
- Mu bọtini Boot mọlẹ lẹhinna tẹ bọtini Tunto lati tẹ ipo Gbigbasilẹ famuwia.
- Lo ohun elo sọfitiwia ti o yẹ lati filasi famuwia sori chirún nipasẹ ibudo ni tẹlentẹle.
Ohun elo Idagbasoke
- Tẹle itọsọna Ibẹrẹ ESP-IDF lati ṣeto agbegbe idagbasoke.
- Ni kete ti o ba ṣeto, o le dagbasoke ati filasi awọn ohun elo tirẹ sori igbimọ ESP32-C6-DevKitC-1.
FAQ
Q: Bawo ni MO ṣe paṣẹ soobu samples ti ESP32-C6-DevKitC-1?
A: Fun awọn ibere soobu, jọwọ ṣabẹwo https://www.espressif.com/en/company/contact/buy-a-sample.
Q: Bawo ni MO ṣe gbe awọn aṣẹ osunwon fun ESP32-C6-DevKitC-1?
A: Fun awọn ibere osunwon, jọwọ tọka si Alaye Ipeṣẹ Ọja Espressif (PDF).
Q: Bawo ni MO ṣe le wiwọn iyaworan lọwọlọwọ nipasẹ module ESP32-C6-WROOM-1 (U)?
A: Awọn akọle J5 lori ESP32-C6-DevKitC-1 le ṣee lo fun wiwọn lọwọlọwọ. Tọkasi awọn alaye ni apakan “Iwọn Iwọn lọwọlọwọ”.
ESP32-C6-DevKitC-1 v1.2 Ẹya agbalagba: ESP32-C6-DevKitC-1 v1.1 Itọsọna olumulo yii yoo ran ọ lọwọ lati bẹrẹ pẹlu ESP32-C6-DevKitC-1 ati pe yoo tun pese alaye ijinle diẹ sii . ESP32-C6-DevKitC-1 jẹ igbimọ idagbasoke ipele titẹsi ti o da lori ESP32-C6-WROOM-1 (U), module idi gbogbogbo pẹlu filasi 8 MB SPI. Igbimọ yii ṣepọ Wi-Fi pipe, Bluetooth LE, Zigbee, ati awọn iṣẹ Thread. Pupọ julọ awọn pinni I / O ti fọ si awọn akọle pin ni ẹgbẹ mejeeji fun ibaramu irọrun. Awọn olupilẹṣẹ le so awọn agbeegbe pọ pẹlu awọn okun onirin tabi gbe ESP32-C6-DevKitC-1 sori apoti akara.
Iwe aṣẹ naa ni awọn apakan pataki wọnyi:
- Bibẹrẹ: Pariview ti ESP32-C6-DevKitC-1 ati hardware/software setup ilana lati to bẹrẹ.
- Itọkasi Hardware: Alaye alaye diẹ sii nipa ohun elo ESP32-C6-DevKitC-1.
- Awọn alaye Atunyẹwo Hardware: Itan atunyẹwo, awọn ọran ti a mọ, ati awọn ọna asopọ si awọn itọsọna olumulo fun awọn ẹya iṣaaju (ti o ba jẹ eyikeyi) ti ESP32-C6-DevKitC-1.
- Awọn iwe aṣẹ ti o jọmọ: Awọn ọna asopọ si awọn iwe ti o jọmọ.
Bibẹrẹ
Abala yii n pese ifihan kukuru ti ESP32-C6-DevKitC-1, awọn itọnisọna lori bi o ṣe le ṣe iṣeto ohun elo akọkọ ati bii o ṣe le filasi famuwia sori rẹ.
Apejuwe ti irinše
Awọn paati bọtini ti igbimọ ni a ṣe apejuwe ni ọna aago kan.
| Ẹya bọtini | Apejuwe |
|
ESP32-C6-WROOM- 1 tabi ESP32-C6- WROOM-1U |
ESP32-C6-WROOM-1 ati ESP32-C6-WROOM-1U jẹ gbogbogbo-
Awọn modulu idi ti n ṣe atilẹyin Wi-Fi 6 ni ẹgbẹ 2.4 GHz, Bluetooth 5, ati IEEE 802.15.4 (Zigbee 3.0 ati Thread 1.3). Wọn ti wa ni itumọ ti ni ayika ESP32-C6 ërún, ati ki o ba pẹlu kan 8 MB SPI filasi. ESP32-C6- WROOM-1 nlo eriali PCB lori-ọkọ, nigbati ESP32-C6-WROOM- 1U nlo asopo eriali ita. Fun alaye diẹ ẹ sii, wo ESP32- C6-WROOM-1 Datasheet. |
|
Akọsori Pin |
Gbogbo awọn pinni GPIO ti o wa (ayafi fun ọkọ akero SPI fun filasi) ti fọ si awọn akọle pin lori ọkọ. |
| 5 V to 3.3 V LDO | Olutọsọna agbara ti o ṣe iyipada ipese 5 V sinu iṣelọpọ 3.3 V. |
| 3.3 V Agbara Lori LED | Tan-an nigbati agbara USB ti sopọ si igbimọ. |
| USB-to-UART
Afara |
Chirún afara USB-si-UART kan n pese awọn oṣuwọn gbigbe to 3 Mbps. |
|
ESP32-C6 USB Iru-C Port |
Ibudo USB Iru-C lori ifaramọ chirún ESP32-C6 pẹlu iyara ni kikun USB 2.0. O ni agbara ti iyara gbigbe 12 Mbps (Akiyesi pe ibudo yii ko ṣe atilẹyin ipo gbigbe iyara giga-iyara 480 Mbps). A lo ibudo yii fun ipese agbara si igbimọ, fun awọn ohun elo ikosan si chirún, fun ibaraẹnisọrọ pẹlu ërún nipa lilo awọn ilana USB, ati fun J.TAG n ṣatunṣe aṣiṣe. |
|
Bọtini bata |
Download bọtini. Diduro mọlẹ Bata ati lẹhinna tẹ Tunto pilẹtàbí famuwia Download mode fun gbigba famuwia nipasẹ awọn tẹlentẹle ibudo. |
| Bọtini atunto | Tẹ bọtini yii lati tun eto naa bẹrẹ. |
|
USB Iru-C to UART Port |
Ti a lo fun ipese agbara si igbimọ, fun awọn ohun elo ikosan si ërún, bakanna bi ibaraẹnisọrọ pẹlu chirún ESP32-C6 nipasẹ afara USB-to-UART lori ọkọ. |
| RGB LED | LED RGB adirẹsi adirẹsi, ìṣó nipasẹ GPIO8. |
|
J5 |
Ti a lo fun wiwọn lọwọlọwọ. Wo alaye ni Abala Lọwọlọwọ Wiwọn. |
Bẹrẹ Idagbasoke Ohun elo
Ṣaaju ṣiṣe agbara ESP32-C6-DevKitC-1 rẹ, jọwọ rii daju pe o wa ni ipo ti o dara laisi awọn ami ibajẹ ti o han gbangba.
Ti beere Hardware
Eto software
Jọwọ tẹsiwaju si ESP-IDF Bibẹrẹ, eyiti yoo ṣe iranlọwọ ni kiakia lati ṣeto agbegbe idagbasoke lẹhinna filasi ohun elo kanample lori ọkọ rẹ.
Awọn akoonu ati apoti
Soobu bibere
Ti o ba bere fun kan diẹ samples, kọọkan ESP32-C6-DevKitC-1 wa ni ẹni kọọkan package ni boya antistatic apo tabi eyikeyi apoti ti o da lori rẹ alagbata.
Fun awọn ibere soobu, jọwọ lọ si https://www.espressif.com/en/company/contact/buy-a-sample.
Awọn aṣẹ Atapọ
Ti o ba paṣẹ ni olopobobo, awọn igbimọ wa ni awọn apoti paali nla.
Fun awọn ibere osunwon, jọwọ ṣayẹwo Espressif Alaye Bere fun Ọja (PDF)
Hardware Reference
Àkọsílẹ aworan atọka
Aworan atọka ti o wa ni isalẹ fihan awọn paati ti ESP32-C6-DevKitC-1 ati awọn asopọ wọn.
ESP32-C6-DevKitC-1 (tẹ lati tobi)
Awọn aṣayan Ipese Agbara
Awọn ọna iyasọtọ mẹta lo wa lati pese agbara si igbimọ:
- USB Iru-C si UART Port ati ESP32-C6 USB Iru-C Port (boya ọkan tabi mejeeji), ipese agbara aiyipada (a ṣe iṣeduro)
- 5V ati awọn akọle pinni GND
- 3V3 ati awọn akọle pinni GND
- Iwọn Iwọn lọwọlọwọ
Awọn akọle J5 lori ESP32-C6-DevKitC-1 (wo J5 ni Figure ESP32-C6-DevKitC-1 - iwaju) le ṣee lo fun wiwọn ti isiyi iyaworan nipasẹ ESP32-C6-WROOM-1 (U) module:
- Iwọn Iwọn lọwọlọwọ
- Yọ jumper: Ipese agbara laarin awọn module ati awọn pẹẹpẹẹpẹ lori awọn ọkọ ti wa ni ge si pa. Lati wiwọn lọwọlọwọ module, so awọn ọkọ pẹlu ohun ammeter nipasẹ J5 afori.
- Waye jumper (aiyipada ile-iṣẹ): Mu iṣẹ ṣiṣe deede ti igbimọ pada.
Akiyesi
Nigba lilo 3V3 ati GND pin afori lati fi agbara si awọn ọkọ, jọwọ yọ J5 jumper, ki o si so ohun ammeter ni jara si awọn ita Circuit lati wiwọn awọn module ká lọwọlọwọ.
Àkọsílẹ akọsori ℑ
Awọn tabili meji ti o wa ni isalẹ pese Orukọ ati Iṣẹ ti awọn akọle pin ni ẹgbẹ mejeeji ti igbimọ (J1 ati J3). Awọn orukọ akọsori pin ti han ni Figure ESP32-C6-DevKitC-1 - iwaju. Nọmba naa jẹ kanna bi ninu ESP32-C6-DevKitC-1 Schematic (PDF).
J1ℑ
| Rara. | Oruko | Iru 1 | Išẹ |
| 1 | 3V3 | P | 3.3 V ipese agbara |
| 2 | RST | I | Ga: kí ni ërún; Low: disables ni ërún. |
|
3 |
4 |
I/O/T |
MTMS 3, GPIO4, LP_GPIO4, LP_UART_RXD, ADC1_CH4, FSPIHD |
|
4 |
5 |
I/O/T |
MTDI 3, GPIO5, LP_GPIO5, LP_UART_TXD, ADC1_CH5, FSPIWP |
|
5 |
6 |
I/O/T |
MTCK, GPIO6, LP_GPIO6, LP_I2C_SDA, ADC1_CH6, FSPICLK |
| 6 | 7 | I/O/T | MTDO, GPIO7, LP_GPIO7, LP_I2C_SCL, FSPID |
|
7 |
0 |
I/O/T |
GPIO0, XTAL_32K_P, LP_GPIO0, LP_UART_DTRN, ADC1_CH0 |
|
8 |
1 |
I/O/T |
GPIO1, XTAL_32K_N, LP_GPIO1, LP_UART_DSRN, ADC1_CH1 |
| 9 | 8 | I/O/T | GPIO8 2 3 |
| 10 | 10 | I/O/T | GPIO10 |
| 11 | 11 | I/O/T | GPIO11 |
| 12 | 2 | I/O/T | GPIO2, LP_GPIO2, LP_UART_RTSN, ADC1_CH2, FSPIQ |
| 13 | 3 | I/O/T | GPIO3, LP_GPIO3, LP_UART_CTSN, ADC1_CH3 |
| 14 | 5V | P | 5 V ipese agbara |
| 15 | G | G | Ilẹ |
| 16 | NC | – | Ko si asopọ |
J3ℑ
| Rara. | Oruko | Iru | Išẹ |
| 1 | G | G | Ilẹ |
| 2 | TX | I/O/T | U0TXD, GPIO16, FPICS0 |
| 3 | RX | I/O/T | U0RXD, GPIO17, FPICS1 |
| 4 | 15 | I/O/T | GPIO15 3 |
| 5 | 23 | I/O/T | GPIO23, SDIO_DATA3 |
| 6 | 22 | I/O/T | GPIO22, SDIO_DATA2 |
| 7 | 21 | I/O/T | GPIO21, SDIO_DATA1, FSPICS5 |
| 8 | 20 | I/O/T | GPIO20, SDIO_DATA0, FSPICS4 |
| 9 | 19 | I/O/T | GPIO19, SDIO_CLK, FSPICS3 |
| 10 | 18 | I/O/T | GPIO18, SDIO_CMD, FSPICS2 |
| 11 | 9 | I/O/T | GPIO9 3 |
| 12 | G | G | Ilẹ |
| 13 | 13 | I/O/T | GPIO13, USB_D+ |
| 14 | 12 | I/O/T | GPIO12, USB_D- |
| 15 | G | G | Ilẹ |
| 16 | NC | – | Ko si asopọ |
- P: Ipese agbara; I: Agbewọle; O: Ijade; T: Ikọju giga.
- Ti a lo lati wakọ LED RGB.
- (1,2,3,4,5) MTMS, MTDI, GPIO8, GPIO9, ati GPIO15 jẹ awọn pinni okun ti chirún ESP32-C6. Awọn wọnyi ni awọn pinni ti wa ni lo lati sakoso orisirisi awọn iṣẹ ni ërún ti o da lori alakomeji voltage iye loo si awọn pinni nigba ërún agbara-soke tabi eto si ipilẹ. Fun apejuwe ati ohun elo ti awọn pinni okun, jọwọ tọka si ESP32-C6 Datasheet> Awọn pinni strapping apakan.
Awọn iwe aṣẹ / Awọn orisun
 |
ESPRESSIF ESP32-C6-DevKitC-1 Development Board [pdf] Itọsọna olumulo ESP32-C6-DevKitC-1 Igbimọ Idagbasoke, ESP32-C6-DevKitC-1, Igbimọ Idagbasoke, Igbimọ |