Elecrow ESP32 AI Camera Development Board Vision Sensor Board

Ẹrọ Awọn ẹya ara

1. Akọsori Agbọrọsọ
2. Imọlẹ RGB
3. Bọtini Al
4. MIC
5. UART Akọsori
6. Iho TF Kaadi
7. Kamẹra
8. Ina Iranlọwọ
9. Bọtini atunto
10. Agbọrọsọ
11. Iru-C Port
12. Imọlẹ agbara
13. Imọlẹ batiri
14. BAT Header

Awọn ọna Itọsọna

• Al Button:
  • In “Al Voice” mode, click to toggle the “Standby/Listening” status.
• Bọtini atunto:
  • Single-click to reboot after firmware flashing failure or device malfunction.
• Imọlẹ Agbara:
  • The red LED is on steadily when powered.
• Imọlẹ Batiri:
  • When powered by the battery, the red light stays on while charging, and the green light stays on when fully charged.

Nẹtiwọọki Sisopọ

1. Plug in the Type-C cable to power on.
2. If you want to use the “Al Online” feature, you need to network pair and register the Al Agent first.
3. Open your phone/computer’s WiFi list, click on “Al_Camera_XXXX” to enter WiFi pairing mode.
   • Ti o ba ti webpage does not open automatically, please visit 192.168.4.1 in your browser.
4. Choose an available 2.4GHz WiFi, enter the WiFi password, and click “Save Configuration”.
   • You can see your Wifi in “WiFi Network”.
   • Akiyesi: If you want to clear your network, open the “Settings” app, then open the “Configure Network”, and click “RECONFIGURE”.
5. Open the “Al Online” app, then open a browser and go to https://portal.thinknode.cc/ to access the Al Hub interface. If this is your first time logging in, you need to click the “Create Account” button to create an account.
6. After the account is successfully created and logged in, you will receive a 5000-point reward.
7. Click the “Al Hub” button to start “Add Agent”.
8. Click “Add Agent” and give your Al Agent a name.
9. Click “Manage devices (0)”, then click “Add Device”, enter the verification code, and confirm.
10. After completing “Add Device”, you can configure the character.
11. If you want to browse “Historical conversations”, you need to first enable “Local Short-term Memory” and save.
    • Akiyesi: If your 5000 points are used up, you need to click “Recharge” to purchase a plan that will allow you to regain points.

Akọkọ Awọn pato

• Orukọ ọja: Al Camera Module
• Alakoso akọkọ ESP32-S3R8
• Ifihan 1.83-inch TFT-LCD Touch Screen
• Awọn piksẹli 2 MP
• Ailokun WiFi & Bluetooth 5.0
• Filaṣi 16MB
• Iho TF Kaadi Ṣe atilẹyin to 128GB
• Ni wiwo UART Interface. IC Pad
• Iṣawọle 5V/1A
• Awọn iwọn 56.05 * 44.5 * 18.6mm
• Awọn iwọn otutu ti nṣiṣẹ -20°C si 65°C

Awọn iwe aṣẹ / Awọn orisun

Elecrow ESP32 AI Camera Development Board Vision Sensor Board [pdf] Itọsọna olumulo ESP32 AI Camera Development Board Vision Sensor Board, ESP32, AI Camera Development Board Vision Sensor Board, AI Camera Development Board Vision Sensor Board, AI Camera Development Board, Camera Development Board, Vision Sensor Board, Sensor Board

Awọn itọkasi

• Itọsọna olumulo