Digilog ESP32 Super Mini Dev Board

Awọn pato

• Orukọ Ọja: ESP32 Super Mini Dev Board
• Ọkọ Iru: ESP32C3 Dev Module
• Ibaraẹnisọrọ: USB CDC
• Oṣuwọn Baud: 9600
• Eewọ LED: GPIO8

Iṣeto-1

Mi ESP32 Super Mini Dev Board (olusin 1) gba awọn aworan afọwọya lati PC kan, ṣugbọn kii ṣe ibasọrọ pẹlu Atẹle Serial (Bd = 9600) botilẹjẹpe LED onBoard (ni GPIO8) blinks.
[aworan|403×203](igberùsókè://pRi2u3tDsAxTivzokiEplEtzhlC.jpeg)
Olusin-1

Iṣeto-1

• Igbimọ: “ESP32C3 Dev Module”
• USB CDC lori Boot: “Ṣiṣe”
• Ibudo: "COM13 (ESP32S3 Dev Module)" //ko si aṣayan miiran

Aworan

• setumo LED_BUILTIN 8
• char myData[10];
• asan iṣeto ()
• Serial.begin (9600);
• pinMode(LED_BUILTIN, OUTPUT)
• ofo lupu()
• digitalWrite (LED_BUILTIN, GIGA); // tan LED naa (GA ni voltage ipele)
• idaduro (1000); // duro fun iṣẹju kan
• digitalWrite (LED_BUILTIN, LOW); // pa LED kuro nipa ṣiṣe voltage LOW idaduro (1000)
• baiti n = Serial.available ();
• ti (n!= 0) {baiti m = Serial.readBytesTiti ('\n', myData, sizeof (myData) -1); myData[m] = '\0'
• Serial.println (myData); }
• Serial.println ("Hello"); }

Eto atẹle ti yanju iṣoro naa.

Iṣeto-2

• Igbimọ: "LOLIN C3 Mini"
• USB CDC lori Boot: “Ṣiṣe”
• Ibudo: "COM13 (ESP32S3 Dev Module)"
• Bd = 9600

Abajade

• Pẹlẹ o
• Pẹlẹ o
• Arduino // Lati InputBox ti SM si ESP32C3 si OutputBox ti SM
• Pẹlẹ o
• Pẹlẹ o

Inu mi yoo dun lati gbọ ero rẹ si - "kini LOLIN C3".

1. Maṣe gbe ESP32C3 Super Mini Board sori Akara lati yago fun awọn iṣoro olubasọrọ.
2. LED inu ọkọ ti sopọ ni DPin-8.
3. Lo akọ-obirin jumper ki o si so awọn obinrin ẹgbẹ ni DPin-9 lati sise bi ohun ita yipada / bọtini.
4. Aworan asopọ ti onFig. 1 LED ati bọtini kan jẹ iru si aworan 1.
5. Yan Igbimọ gẹgẹbi atẹle: IDE 2.3.1 -> Awọn irinṣẹ -> ESP32.
6.  LOLIN C3 Mini USB CDC Lori Boot: Ti ṣiṣẹ.
7. Po si awọn Sketch pese si awọn ọkọ.
8. Ṣayẹwo pe LED ti inu ọkọ wa ni pipa ni ibẹrẹ.
9. Pipade iyipada yoo jẹ ki LED ti inu ọkọ bẹrẹ si paju ni aarin iṣẹju-aaya kan.
10. Rii daju pe LED inu ọkọ wa lori.f
11. Fi ọwọ kan awọn ọkunrin apa ti awọn ikele waya / jumper pẹlu h G-pin ti awọn Mini Board.
12. Jẹrisi pe LED ti inu ọkọ n paju ni aarin iṣẹju-aaya kan.
13. Tẹ bọtini RST (Tunto) ti Mini Board ki o tun ṣe ilana naa ti o ba nilo.

Awọn iwe aṣẹ / Awọn orisun

Digilog ESP32 Super Mini Dev Board [pdf] Awọn ilana ESP32 Super Mini Dev Board, ESP32, Super Mini Dev Board, Mini Dev Board, ọkọ

Awọn itọkasi

• Itọsọna olumulo