dewenwils MST01 Latọna Iṣakoso Atagba

ọja Alaye

Jọwọ san ifojusi si awọn ami ikilọ
Ka awọn itọnisọna pẹlu iṣọra ṣaaju ṣiṣe ati tọju rẹ daradara

Apejuwe

1. Function knob switch
2. Delay knob switch
3. Sensitivity knob switch
4. Apoti batiri
5. Iṣagbesori akọmọ
6. Lẹnsi

Ifihan iṣẹ

1. Awọn ipo 5 ti atagba sensọ išipopada alailowaya “iyipada bọtini iṣẹ”:
   

   MAT （Match Mode）	When the knob is set to this mode, the induction transmitter will send an on and off signal to the receiver every 3 seconds, whether it is day or night, and stop sending any signal after sending 10 sets of on and off signals. Akiyesi: Ipo yii jẹ lilo julọ fun sisopọ olugba ati igbeyewo awọn ọja.
   PIR （Motion Detection Mode）	When the knob is set to this mode, the sensor transmitter monitors human activity during the day or at night. When human activity is detected, the sensor transmitter transmits an on signal to the receiver; when the receiver on time reaches the delay time preset by the TIME knob and no one passes by the sensor, the product transmits a off signal to the receiver.
   NTM （Night Time Motion Mode）	When the knob is set to this mode, the sensor transmitter does not monitor human activities during the day, and starts monitoring human activities in the evening after the sensor transmitter detects that the light reaches the

   	bẹrẹ imọlẹ. When human activities are detected, the sensor transmitter will send an on signal to the receiver; when the receiver on time reaches the delay time preset by the TIME knob and no one passes by the sensor, the product sends a shut-down signal to the receiver.
   DTD （Dusk to Dawn Mode）	When the knob is set to this mode, the sensor transmitter is only affected by the current ambient brightness. In the evening, when the sensor transmitter detects that the light reaches the start-up brightness, it will send a start signal to the receiver; at dawn, when the sensor transmitter detects that the light reaches the shutdown brightness, it will send a shutdown signal to the receiver after a delay of 1 minute.
   RND （Random Mode）	When the knob is set to this mode, the sensor transmitter will send an open signal and a close signal to the receiver at irregular intervals in the evening. The random time range is from 1 minute to 30 minutes. At dawn, when the sensor transmitter detects that the light reaches the shutdown brightness, it will send a close signal to the receiver after a delay of 1 minute.

   NOTE: To activate the desired function, turn the rotary switch to the letter that corresponds to that mode.
2. Setting the “Delay Knob Switch” of the Wireless Motion Sensor Transmitter In “PIR” or “NTM” mode, you can adjust the TIME knob to pre-set the time the product can keep the receiver turned on after the last human activity is detected. Note:
   1. The time range is adjustable from 10 seconds to 30 minutes.
   2. The “Delay Knob Switch” does not work in “RND”, “DTD” and “MAT” modes.
3. Setting the “Sensitivity Knob Switch” of the Wireless Motion Sensor Transmitter In “PIR” or “NTM” mode, you can adjust the SENS knob to set the sensitivity of human detection.
   Akiyesi:
   1. When the SENS knob is set to “Min”, the maximum sensing distance can be up to 3 meters.
   2. When the SENS knob is set to “Max”, the maximum sensing distance can be up to 15 meters.
   3. The “Sensitivity Knob Switch” does not work in “RND”, “DTD” and “MAT” modes.

Awọn ilana fun lilo akọkọ ti ọja naa

1. Install the receiver (refer to the receiver installation wiring diagram in the manual).
2. Install the battery in the wireless motion sensor transmitter (refer to the battery installation method in the manual).
3. Turn the transmitter’s “function knob switch” to “MAT” mode to check whether the transmitter can control the receiver normally.
4. If the transmitter and receiver function normally, please adjust the transmitter’s “function knob switch” to the required mode.
5. Install the transmitter to the required location (Install the transmitter mounting bracket in the desired location with the included screws.
   Akiyesi: The installation height of the transmitter from the ground should not be less than 3ft and not more than 7ft.)

Akiyesi: When the transmitter’s “function knob switch” is turned to “MAT” mode and the transmitter cannot control the receiver normally, please check according to the following steps.

1. Check whether the receiver is wired correctly;
2. Ṣayẹwo boya batiri ti fi sori ẹrọ daradara.
3. Re-pair the receiver and transmitter. (Refer to the pairing programming in the manual)

Bii o ṣe le Fi Batiri ti Atagba sensọ išipopada Alailowaya sori ẹrọ

1. Turn the battery cover at the bottom of the battery box to the “unlock” position and pull out the battery cover.
2. Take out the black battery compartment inside the battery box and install 3 AAA NiMH batteries.
3. Insert the black battery compartment containing the batteries into the battery box.
4. Insert the battery cover into the bottom of the battery box and screw it to the “lock” position.

Akiyesi: When the blue indicator light in the lens of the wireless motion sensor transmitter keeps flashing, it means that the battery power of the transmitter is too low. Please replace the battery in time.

Siseto bata

The receiver and transmitter are pre-programmed and ready for immediate use, but there are a few devices that may not be pre-programmed or programmed incorrectly, or you may want to customize the configuration to suit your needs.
Please follow the steps below to program the transmitter and receiver:

1. Press the “Program Button” on the receiver for 3 seconds until its indicator light starts to flash slowly.
2. Release the “Program Button” on the receiver and turn the “Function Knob Switch” on the remote control to “MAT” mode.
3. When the indicator light on the receiver stops flashing and remains on, it means that the product pairing and programming is successful.
4. Adjust the “Function Knob Switch” on the transmitter to the required mode as needed.
   Imọran: Each transmitter can be paired to control multiple receivers; each receiver can also be paired with multiple transmitters.

Fagilee siseto
Cancel all programs so that the remote control transmitter cannot control the receiver:

1. Press the “Programming Button” on the receiver for 6 seconds until its indicator light starts flashing quickly.
   (Akiyesi: The indicator light on the receiver flashes from slow to fast.)
2. Release the “Programming Button” on the receiver.
3. Then short-press the “Programming Button” on the receiver again. When its indicator light goes out, it means that the programming has been successfully canceled.

Awọn pato

• Igbohunsafẹfẹ gbigbe: 433.92MHz
• Ijinna Iṣakoso Latọna jijin: 100 ft (Agbegbe Ọfẹ)
• Igun wiwa:240°
• Ijinna wiwa: 50ft

FCC Ikilọ

Ẹrọ yii ni ibamu pẹlu apakan 15 ti Awọn ofin FCC. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:

1. Ẹrọ yii le ma fa kikọlu ipalara, ati
2. Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa isẹ ti ko fẹ.

Eyikeyi awọn iyipada tabi awọn iyipada ti ko fọwọsi ni pato nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ohun elo naa.

Akiyesi: Ohun elo yii ti ni idanwo ati rii lati ni ibamu pẹlu awọn opin fun ẹrọ oni nọmba Kilasi B, ni ibamu si apakan 15 ti Awọn ofin FCC. Awọn opin wọnyi jẹ apẹrẹ lati pese aabo to tọ si kikọlu ipalara ni fifi sori ibugbe kan. Ẹrọ yii n ṣe ipilẹṣẹ awọn lilo ati pe o le tan agbara ipo igbohunsafẹfẹ redio ati, ti ko ba fi sii ati lo ni ibamu pẹlu awọn ilana, o le fa kikọlu ipalara si awọn ibaraẹnisọrọ redio. Sibẹsibẹ, ko si iṣeduro pe kikọlu ko ni waye ni fifi sori ẹrọ kan pato. Ti ohun elo yii ba fa kikọlu ipalara si redio tabi gbigba tẹlifisiọnu, eyiti o le pinnu nipasẹ titan ohun elo naa ni pipa ati tan, a gba olumulo niyanju lati gbiyanju lati ṣatunṣe kikọlu naa nipasẹ ọkan tabi diẹ ẹ sii ti awọn iwọn wọnyi:

• Reorient tabi tun eriali gbigba pada.
• Mu iyatọ pọ si laarin ẹrọ ati olugba.
• So ohun elo pọ si ọna iṣan lori Circuit ti o yatọ si eyiti olugba ti sopọ.
• Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.

Ohun elo yii ni ibamu pẹlu awọn opin ifihan itankalẹ FCC ti a ṣeto fun agbegbe ti a ko ṣakoso. Ohun elo yii yẹ ki o fi sori ẹrọ ati ṣiṣẹ pẹlu aaye to kere ju 20cm laarin imooru & ara rẹ.

FAQ

• Q: Ṣe MO le lo Yipada Knob Idaduro ni gbogbo awọn ipo?
  A: No, the Delay Knob Switch only works in PIR and NTM modes.
• Q: Kini ijinna oye ti o pọju ti o da lori eto Knob Sensitivity?
  A: When set to Min, the maximum distance is 3 meters; when set to Max, it is 15 meters.

Awọn iwe aṣẹ / Awọn orisun

dewenwils MST01 Latọna Iṣakoso Atagba [pdf] Ilana itọnisọna 2A4G9-024, 2A4G9024, 024, MST01 Atagba isakoṣo latọna jijin, MST01, Atagba isakoṣo latọna jijin, Atagba Iṣakoso, Atagba.

Awọn itọkasi

• Itọsọna olumulo