CITECH RM10 Bluetooth Dual Mode Module
Awọn pato
| Awọn ẹka | Awọn ẹya ara ẹrọ | imuse |
| Chip | QCC3083 | |
| Ẹya Bluetooth | V5.1 Meji-mode | |
| 2402MHz ~ 2480MHz | ||
| Awọn oṣuwọn Data Aise (Atẹgun) | Mbps (Classic BT – BR/EDR) | |
| Olumulo Ọlọpọọmídíà
Awọn agbeegbe |
UART Ọlọpọọmídíà | TX, RX, CTS, RTS |
| Gbogbo Idi I/O | ||
| Default 115200, N,8,1 | ||
| Atilẹyin Baudrate lati 1200 si 4000000 | ||
| GPIO | 20 (o pọju - Configurable) ila | |
| Agbara wakọ O/P (2, 4, 8, tabi 12 mA) | ||
| Atako ti o fa soke (33 KΩ) iṣakoso | ||
| SPI Interface | SPI debug and programming interface with read access disable locking | |
| USB Interface | 1 full-speed (12Mbps) | |
| Ipese Voltage | Ipese | 4.75V ~ 5.5V |
Pariview
RM10 is a Bluetooth dual-mode module series. It supports a Bluetooth Low Energy and compliant system for audio and data communication. RM10 integrates an ultra-low-power DSP and application processor with embedded flash memory, a high-performance stereo codec, a power management subsystem, I2S, LED drivers, and ADC I/O in a SOC IC. Both cores use external flash to execute code, making it easy for users to differentiate products from new features without delaying the development. By default, the RM10 module is equipped with powerful and easy-to-use Feasycom firmware. It’s easy to use and completely encapsulated. Feasycom firmware enables users to access Bluetooth functionality with simple ASCII commands delivered to the module over a serial interface – it’s just like a Bluetooth modem. Therefore, RM10 provides an ideal solution for developers who want to integrate Bluetooth wireless technology into their design.
Awọn ẹya ara ẹrọ
- Ti o yege si Bluetooth® v5.1 sipesifikesonu
- 32 MHz Olùgbéejáde isise fun awọn ohun elo
- Firmware Processor for the system
- Awọn algoridimu ohun afetigbọ
- Ni wiwo ohun sitẹrio 24-bit ti o ga julọ
- Digital ati afọwọṣe gbohungbohun atọkun
- I2S/PCM, SPDIF interfaces input/output
- Awọn kodẹki ohun afetigbọ SBC ati AAC ṣe atilẹyin
- Serial interfaces: UART, Bit Serializer (I²C/SPI) ,USB 2.0
- PMU ti a ṣepọ: SMPS meji fun eto/awọn iyika oni-nọmba, ṣaja batiri Li-ion Integrated
Ohun elo subsystem
Meji-mojuto ohun elo subsystem 32 MHz isẹ
32-bit Firmware Processor:
- Ni ipamọ fun eto lilo
- Ṣiṣe akopọ oke Bluetooth, profiles, and house-keeping code
32-bit Developer Processor:
- Ṣiṣe awọn ohun elo idagbasoke
- Mejeeji ohun kohun ṣiṣẹ koodu lati ita filasi iranti lilo QSPI clocked ni 32MHz
- Awọn caches lori-chip fun mojuto gba laaye fun iṣẹ iṣapeye ati lilo agbara
Bluetooth subsystem
- Qualified to Bluetooth v5.1 specification, including
- 2 Mbps Bluetooth low energy(Production parts)
- Single-ended antenna connection with on-chip balun and Tx/Rx switch
- Bluetooth, Bluetooth low energy, and mixed topologies are supported
- Atilẹyin kilasi 1
Ohun elo
- Bluetooth agbohunsoke
- Apoti orin Bluetooth
PIN Definition Awọn apejuwe
| 1 | I2S_PCM_DOUT[0] | 22 | PIO-32 |
| 2 | PIO-31 | 23 | GND |
| 3 | I2S_PCM_MCLK | 24 | GND |
| 4 | BT_UART_TX | 25 | BT_UART_RTSN |
| 5 | I2S_PCM_SYNC | 26 | GND |
| 6 | BT_UART_CTSN | 27 | BT_UART_RX |
| 7 | GND | 28 | GND |
| 8 | PIO-33 | 29 | GND |
| 9 | GND | 30 | I2S_PCM_DIN[0] |
| 10 | GND | 31 | GND |
| 11 | VCC_5V0 | 32 | GND |
| 12 | BT_USB_DN | 33 | GND |
| 13 | VCC_5V0 | 34 | GND |
| 14 | BT_USB_DP | 35 | GND |
| 15 | VCC_5V0 | 36 | GND |
| 16 | GND | 37 | GND |
| 17 | BT_SYS_CTRL | 38 | GND |
| 18 | TBR_MOSI | 39 | GND |
| 19 | TBR_CLK | 40 | GND |
| 20 | BT-RESET# | 41 | GND |
| 21 | TBR_MISO | 42 | GND |
| 43 | GND | 48 | GND |
| 44 | GND | 49 | GND |
| 45 | GND | 50 | GND |
| 46 | GND | 51 | 1V8_SMPS |
| 47 | GND | 52 | GND |
Awọn alaye ẹrọ
Awọn ilana Lilo
Agbara Ipese Asopọ
So ipese voltage within the specified range of 4.75V to 5.5V to power the Bluetooth module.
Awọn isopọ Ọlọpọọmídíà
Make the necessary connections for TX, RX, CTS, RTS, General Purpose I/O, UART, SPI, and USB interfaces as per the provided pin definitions.
Asopọ Bluetooth
Follow the standard Bluetooth pairing procedure to connect the module to your desired host device.
Gbigbe data
Utilize the implemented interfaces for data transmission at the supported data rates over the Bluetooth connection.
FCC Ifọwọsi
Ẹrọ yii ni ibamu pẹlu Apá 15 ti Awọn ofin FCC. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:
- Ẹrọ yii le ma fa kikọlu ipalara, ati
- Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa isẹ ti ko fẹ.
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, nd can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient tabi tun eriali gbigba pada.
- Mu iyatọ pọ si laarin ẹrọ ati olugba.
- So ẹrọ pọ si ohun iṣan lori kan Circuit yatọ si lati eyi ti awọn olugba ti a ti sopọ.
- Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device should be installed and operated with minimum 20 cm between the radiator and your body.
AWỌN ỌRỌ IṢỌRỌ
Akojọ ti awọn ofin FCC to wulo
This module complies with Part 15.247 of the FCC rule. Summarize the specific operational use conditions. Not applicable.e
Lopin ilana module
This is Limited modular approval as this module is limited to installation by the grantee into our host systems. This module is certified as limited modular approval as it does not have its own power supply regulator, therefore the host device must supply a rated voltage(5V) using a voltage regulator or equivalent.
Akiyesi: Please check that the voltage is between 4.75V and 5.5V when a rated voltage is applied to the module. Host product manufacturers are responsible to follow the integration guidance and to perform a limited set of transmitter module verification testing, to ensure the end product is in compliance with the FCC rules.
Wa kakiri eriali awọn aṣa
Ko ṣiṣẹ fun
RF ifihan ero
This module complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. If RF exposure statements and use conditions are not provided, then the host product manufacturer is required to take responsibility for the module through a change in FCC ID (new application). Antenna: The antenna that can be used with the transmitter is as follows. Antenna Model Name: RS151, Type: PCB Antenna, Gain: 2.7,6dBi Cable: RPSMA to IPEX Cable, Loss: 0.46dB
Aami ati alaye ibamu
The module is labeled with its own FCC. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, in the end product must be labeled in a visible area with the following: “Contains FCC ID: 2ANYL-RM10.” The host manual shall include the following regulatory statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- Ẹrọ yii le ma fa kikọlu ipalara, ati
- Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa iṣẹ ti ko fẹ.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device should be installed and operated with a minimum of 20 cm between the radiator and your body.
Alaye lori awọn ipo idanwo ati awọn ibeere idanwo afikun
Testing of the host product with all the transmitters installed – referred to as the composite investigation test- is recommended to verify that the host product meets all the applicable FCC rules. The host manufacturer can use the software to control the RF signal during the etest
Idanwo afikun, Apá 15 Subpart B AlAIgBA
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The host product may need to be evaluated against the FCC Part 15B criteria for unintentional radiators to be properly authorized for operation as a Part 15 digital device. Note EMI Considerations: Not applicable.
FAQs
Q: Kini oṣuwọn baud aiyipada fun wiwo UART?
A: The default baud rate for the UART interface is set to 11520 0,N,8,1, but it supports baud rates ranging from 1200 to 4000000.
Awọn iwe aṣẹ / Awọn orisun
 |
CITECH RM10 Bluetooth Dual Mode Module [pdf] Awọn ilana RM10, 2ANYL-RM10, 2ANYLRM10, RM10 Bluetooth Dual Mode Module, RM10, Bluetooth Dual Mode Module, Dual Mode Module, Mode Module |
