Quick Installation Guide &Warranty Card
AC1200 Wi-Fi Nano Router
Model Y7
All rights reserved
Without the express written permission of YINUOLINK CO., LTD, no entity or individual shallcopy, copy or translate the contents of the Manual in part or in whole, and shall not transmit the contents by any means (electronic, photocopied, recorded, etc.) for profit.
is a registered trademark of YINUOLINK CO.,
LTD. All trademarks mentioned in this manual are the property of their respective owners. Product specification sand advice mentioned in this manual are for reference only and are subject to change without prior notice. Unless other wise specified, this manual is intended only as a guide to use and the statements made herein constitute any form of warranty.
Multi-Mode Introduction
During Travel
A. AP Router Mode (Default)
Connect to Ethernet to instantly create a private wireless network and share internet access to all your Wi-Fi devices.
B. AP Client Router Mode (WISP)
Suitable for relay amplification of WiFi hotspot signals provided by operators, such as: CMCC, China Unicom, ChinaNet, etc.
C. Access Point Mode
Create a wireless network for Wi-Fi enabled devices.
D. Client Mode
Allow devices that require a wired connection to access an existing Wi-Fi network.
Note: 5.8G can be used normally for WiFi if you are 2.4G connected to the parent AP, and 2.4G can be used normally for WiFi if you are 5.8G connected to the parent AP.
E. Repeater Mode
Extend existing Wi-Fi to improve signal strength and maximize coverage.
F. Bridge Mode
Boost existing Wi-Fi to improve signal strength.
Connect the Hardware
Connect to power outlet
Wait about 50s until the device has finished booting up.
If your internet comes from an Ethernet outlet instead of a DSL/Cable / Satellite modem, connect the router’s WAN port to it.
Create an instant private wireless network and share internet to multiple Wi-Fi devices. This mode is suitable for hotel rooms and home networks.
Note: If the hotel’s internet has an authentication process, you will need to authenticate only once and only on one device.
LED Explanation
| Status | Indication |
| Solid Red | Device starting |
| Flashing Red | Start completion |
| Solid Green | Network connection successfully. Moderate distance from router/main AP, when in Repeater, Bridge, Client, WISP Mode. |
| Blue light solid on | Successful networking is far away from the AP, when in Repeater, |
Bridge, Client, WISP Mode.
Interface Explanation
Reset Button: Press and hold the reset button for more than 5 seconds until it resets.
WAN/LAN Interface
a. WAN Interface: For connecting to a modem or an Ethernet outlet.
b. LAN Interface: For connecting your PC or other wired devices to the router.
Set Up Router
a. Open Settings > WiFi Search for the network name” Y7-2.4G_XXXX or Y7_5G_XXXX” and connect it.
Note: It’s an open network so it shows up unsecured you just need to connect to it.
b. Open a browser (Safari, Google Chrome, Fire fox) and type 192.168.100.1 or scan QR Code:
Note: If the login page does not appear, please refer to Q1 of Need Help? in this guide.
c. After login, you can see the system status page. For more function configurations, please contact device supplier.
Need Help?
Q1. What should I do if I can't access the web management page?
a. Reset your router and try again. b. If your computer is set to obtain an IP address automatically, change its settings to a static IP, ie 192.168.100.X (X is any integer between 2 and 253) c. Enter http://192.168.100.1 in the web browser. d. Use another web browser and try again. e. Disable and enable the network adapter in use.
Q3. What should I do if I can't access the internet in router mode?
a Power off your modern for about 5 minutes, then power it on and check the internet. If your modem has more than one Ethernet port, keep other ports unconnected b. Check if the internet is working normally by connecting a computer directly to the modem via an Ethernet cable. If it is not contact your internet service provider. c. Reset
Q4. What should I do if I forget my wireless password?
a. Reset, unencrypted by default.
Q5. What should I do if I forget my web management page password?
a. Reset, default password admin.
Q6. What should I do if my wireless signal is unstable or too weak?
a. It may be caused by too much interference. Use the device wireless protocol is not compatible, modify the wireless network protocol 11AX to 11AC c. Choose a location with less obstacles that may block the signal between the travel router and the host AP. An open corridor or a spacious location is ideal. d. Move the router to a new location away from Bluetooth devices and other household electronics, such as cordless phones, microwaves, and baby monitors, to minimize signal interference. e In Range Extender mode, the ideal location to place the router is halfway between your host AP and the Wi-Fi dead zone. If that is not possible, place the router closer to your host AP to ensure stable performance.
Safety Information
a. Keep the device away from water, fire, humidity or hat environments.
b. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
c. Do not use the device where wireless devices are not allowed.
Product Warranty Card
- Below following cases, it is out of the warranty scope. Yinuo-Link can provide paid services, Please note
The return/warranty period was exceeded. Failures to install, use, maintain or keep the product according to the instructions.
Alter without authorization. Tear up product barcode Without Yinuo-Link authorization, modify the inherent Settings of the file or unauthorized dismantling repair.
Damage to the product caused by accident or human behavior/such as focusing on bright light, inappropriate voltage input, high temperature, water, mechanical damage, breaking, serious oxidation or rusting of the product. Product failure or damage caused by force majeure such as earthquakes, fires, floods, lightning strikes, etc.
Other failures or damages that are not caused by the product’s own design, technology, manufacturing, quality, etc. - Technical support and software upgrade service.
Before you send the product for repair, please call our technical support hotline: +86 17302628626 to identify product failures. You can also send email to support@yinuo-link.com for technical support. - YINUO-LINK Provide One-year warranty service.
For more information, please refer to official website of www.yinuc-link.com.
Special Note
If there are obvious hard object damage, cracks, broken feet, severe deformation, broken power cord, broken wire, bare core, etc. Due to improper use by the customer or accidental factors, it will not be guaranteed and replaced, and user can purchase it separately.
Warranty replacement service is limited to the mainframe. Packaging, cables, software products, technical documents and other accessories are not covered into the warranty. The warranty period for the external antennas and main components is 3 months. If there are equipment performance problems within 15 days after the product purchased, and the appearance is not scratched, please contact supplier for replacement.
During the free warranty period, the product must be inspected by Yinuo-Link After the fault is confirmed, the same model or a repaired product with the same performance as the product will be replaced. The replaced defective product belongs to Yinuo-Link, the normal product will be returned as it is. Please provide product warranty card for warranty service.
If you are not able to provide, the free warranty period of the product will be calculated from its production date. If the product is charge for repair, the same problem will have a free warranty period of three months from the date of repair.
Please request and keep your repair receipt.
The shipping cost of the repaired product is request to charge to the sender. - Within the scope of national laws and regulations, the right of interpretation and maintenance of this commitment belongs to YINUOLINK CO., LTD.
Federal Communication Commission (FCC)
Radiation Exposure Statement:
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful Interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Documents / Resources
 |
YINUOLINK Y7 AC1200 Wi-Fi Nano Router [pdf] Installation Guide 2A66J-Y7, 2A66JY7, Y7 AC1200 Wi-Fi Nano Router, Y7, AC1200 Wi-Fi Nano Router, Wi-Fi Nano Router, Nano Router, Router |