Cosmic Byte ECLIPSE TRI Mode Controller User Manual

ECLIPSE TRI Mode Controller

EActllipasse TRI-MODE MOUSE TRI MODE CONTROLLER USER MANUAL

ספּעסאַפאַקיישאַנז

• קאַנעקשאַן מאָדעס: 2.4GHz Wireless, Bluetooth, Wired (USB Type-C)
• קאַמפּאַטאַבילאַטי: PC, Android, iOS (iOS 13.0 and above with MFi-supported games), other Bluetooth-enabled devices
• ABXY Layout: Switchable (XBOX-style and Alternate-style)
• Trigger Travel: Adjustable (Long/Short)
• ווייבריישאַן: 4 אַדזשאַסטאַבאַל לעוועלס (0%, 30%, 70%, 100%)
• ABXY Lighting: 4 adjustable brightness levels (0%, 30%, 70%, 100%)
• מאַקראָ פּראָגראַממינג: M1/M2 buttons, up to 21 programmable buttons (A/B/X/Y/D-pad/LB/RB/LT/RT/L3/R3/Menu/View/Joysticks)
• דזשויסטיק שפּאַנונג: Adjustable via roller mechanism
• מאַכט אַוועק: Manual (hold Home button 5s) or Auto (10 mins inactivity)
• טשאַרדזשינג: USB-C, Wireless Charging Contacts

באַניץ אינסטרוקציעס

פּראָדוקט איבערview

The controller supports 2.4GHz Wireless, Bluetooth, and Wired (USB Type-C) connection modes. It is compatible with PC, Android, iOS (iOS 13.0 and above with MFi-supported games), and other Bluetooth-enabled devices.

מאָדע סוויטשינג

Use the Mode Switch Button. From left to right, the positions are: Bluetooth – 2.4G – NS (Xinput Bluetooth, 2.4G Receiver, Switch).

ינדיקאַטאָר ליגהץ

• HOME CB Indicator Light: Blue for iOS and Android, Orange for 2.4G Mode.
• Channel Indicator Light (LED 1/2/3): Indicates current channel/mode.

ריקאַנעקשאַן

To reconnect to the last paired device (with the same mode), short-press the Home button.

ABXY Lighting Adjustment

דרוק M + Right Stick Left or רעכט to adjust brightness. There are 4 brightness levels: 0%, 30%, 70%, 100%.

ווייבריישאַן ינטענסיטי אַדזשאַסטמאַנט

דריקן און האַלטן M + Right Stick Up to increase vibration intensity. Press and hold M + Right Stick Down to decrease. There are 4 levels: 0% (off), 30%, 70%, 100%.

ABXY אויסלייג סוויטש

Use the layout switch on the front of the controller to toggle between XBOX-style and Alternate-style layouts.

Rapid Trigger Adjustment

Adjust the LT/RT trigger travel distance using the trigger mode switch on the back for quick/short press functionality.

Macro Programming (M1/M2 Buttons)

1. While connected, hold M + M1 or M2 פֿאַר 3 סעקונדעס צו אַרייַן פּראָגראַממינג מאָדע.
2. Press the desired button(s) to assign (e.g., A, B, etc.).
3. דרוק M1 or M2 ווידער צו ראַטעווען און אַרויסגאַנג.

באַמערקונג: If no button is selected, M1/M2 will be blank. Up to 21 programmable buttons: A/B/X/Y/D-pad/LB/RB/LT/RT/L3/R3/Menu/View/Joysticks.

מאַכט אַוועק

• Hold the Home button for 5 seconds to power off.
• The controller will auto power-off after 10 minutes of inactivity.

קאָנטראָללער באַשטעטיק

Use a small pin to press the Reset hole to restore factory settings.

Joystick Force Adjustment (Roller-Based)

The Cosmic Byte Eclipse controller features adjustable joystick tension using a built-in roller mechanism. Follow these steps to customize the joystick force:

1. Locate the joystick roller at the base of each analog stick.
2. To increase joystick resistance, rotate the roller clockwise.
3. To decrease joystick resistance, rotate the roller counter-clockwise.
4. Make adjustments gradually and test after each rotation to find your preferred setting.

באַמערקונג: The roller mechanism allows for fine-tuning of joystick stiffness for better precision or quicker flick response in different game types (e.g., FPS vs Racing).

מאָביל אַפּ אראפקאפיע

Download and install the KeyLinker App from the Google Play Store or Apple App Store for advanced customization and controller adjustments.

טראָובלעשאָאָטינג

Q1: My controller is not turning on. What should I do?

A: The battery might be completely drained. Please charge the controller using the provided USB Type-C cable for at least 30 minutes. If it still doesn’t power on, try using a different USB port or cable to verify the power source.

Q2: The controller is not connecting through Bluetooth. How can I fix it?

A: Make sure the mode switch is set to Bluetooth (Left position). Press and hold the Pairing button for 3 seconds until the logo indicator flashes rapidly. On your device, enable Bluetooth and select “Xbox Wireless Controller”. If the controller still doesn’t connect, delete any old pairing entries, then try again. If the issue persists, use a small pin to press the Reset hole and retry pairing.

Q3: The controller is not connecting in 2.4G wireless mode. What should I do?

A: Ensure the 2.4G receiver dongle is properly inserted into the device’s USB port (avoid USB hubs). Switch the mode toggle to 2.4G (Middle position). Hold the Pairing button for 3 seconds – when the logo light turns solid and the controller vibrates, the connection is complete.

FAQ

• פ: ווי אזוי ווייס איך אין וועלכע מאָדע דער קאָנטראָללער איז?
  A: The Home button indicator light will be Blue for iOS/Android and Orange for 2.4G Mode. The Channel Indicator lights (LED 1/2/3) also show the current mode.
• ק: קען איך נוצן די קאָנטראָללער בשעת עס איז טשאַרדזשינג?
  A: Yes, the controller supports wired connection via USB-C, allowing you to play while charging.
• Q: What is the purpose of the M button?
  A: The M button is used in combination with other buttons for advanced functions like adjusting lighting, vibration, and macro programming.
• Q: How do I switch between XBOX and Alternate ABXY layouts?
  A: Use the dedicated ABXY Layout Switch located on the front of the controller.
• Q: What devices are compatible with the KeyLinker App?
  A: The KeyLinker App is available for download on Google Play Store (Android) and Apple App Store (iOS).

Loading PDF…

−+Fit width100%View FullscreenDownload PDFPrint PDF

×

Loading PDF…

EActllipasse TRI-MODE MOUSE TRI MODE CONTROLLER
באַניצער מאַנואַל

View Button Left Joystick (Press Down: LS) Resistance Adjustment Knob
ד-פּאַד
RB

היגהליגהץ

Home Button (Logo Light)
M Button Channel Indicator light (LED 1/2/3)

מעניו קנעפּל
סקרעענשאָט קנעפּל
א / ב / רענטגענ / י קנעפּלעך
Right Joystick (Press Down: RS)
ABXY אויסלייג סוויטש
קעגנשטעל אַדזשאַסטמאַנט קנופּ

וסב- C פּאָרט

LB

RT

פּערינג קנעפּל

LT

Trigger Travel Switch (Long/Short)

Wireless Charging Contacts

M2

M1

מאָדע באַשטימען קנעפּל

באַשטעטיק האָלע

מיני דאָנגלע
Mode Switching Position: From left to right: Bluetooth – 2.4G – NS (Xinput Bluetooth, 2.4G Receiver, Switch)

פּראָדוקט איבערVIEW
Supports 2.4GHz Wireless, Bluetooth, and Wired (USB Type-C) connection modes. Compatible with PC, Android, iOS (iOS 13.0 and above with MFi-supported games), and other Bluetooth-enabled devices.
אָפּעראַציע אינסטרוקציעס
1. HOME CB Indicator Light – Blue – iOS and Android – Orange – 2.4G Mode
2. First-Time Connection · 2.4G Wireless Mode – Set the mode switch toggle to 2.4G (Middle). – Plug the USB receiver into your device. – While the controller is powered off, press and hold the Pairing button for 3 seconds. – The logo indicator will flash rapidly. Once it turns solid and the controller vibrates briefly, the connection is successful. · Bluetooth Mode – Set the mode switch toggle to Bluetooth (Left). – While powered off, press and hold the Pairing button for 3 seconds. – The logo indicator will flash rapidly. – On your device (PC/Android/iOS), enable Bluetooth and select ‘Xbox Wireless Controller’. – When the logo light turns solid and the controller vibrates, the pairing is complete. · Wired Mode – Connect the controller to your device using the included USB Type-C cable. – Wired mode activates automatically when connected.

3. Reconnection To reconnect to the last paired device (with the same mode), short-press the Home button.
4. Joystick Adjustment · Dead Zone Toggle: – Press and hold Left and Right Stick (LS/RS) for 5 seconds to switch between 5% and 0% deadzone. – Controller will vibrate to confirm the change. · Active Zone Shape Toggle: – Press and hold M + LS or RS for 5 seconds to toggle between 10% square zone and 0% circle zone.
5. Turbo and Continuous Fire · Manual Turbo – Press M + A while holding the A button to enable manual turbo (continuous fire). – Logo light will flash red rapidly. · Auto Turbo – Press M + A again to switch to auto turbo. Press again to cancel turbo. – A single press of A will now fire continuously. · Clean all Turbo – Press M button twice and hold M for 5 secs, controller will vibrate & clean all Turbo settings. · Turbo Speed Adjustment – Hold M + Right Stick Up/Down to increase or decrease turbo speed. – Vibration feedback indicates change. Note: Turbo can be assigned to A/B/X/Y/LB/LT/RT/D-pad only.
6. ABXY Lighting Adjustment – Press M + Right Stick Left and Right to adjust brightness. – 4 Brightness Levels: 0% 30% 70% 100%

7. Vibration Intensity Adjustment – Press and hold M + Right Stick Up to increase vibration intensity. – Press and hold M + Right Stick Down to decrease. – 4 Levels: 0% (off) 30% 70% 100%
8. ABXY Layout Switch – Use the layout switch on the front to toggle between XBOX-style and Alternate-style layouts.
9. Rapid Trigger Adjustment – Adjust LT/RT trigger travel distance using the trigger mode switch on the back for quick/short press functionality.
10. Calibration · Stick & Trigger Calibration – Power on the controller. – Hold View + M + Menu for 3 seconds to enter calibration. – LED1 and LED3 will flash. – Rotate both sticks clockwise 3 full turns. – Fully press both triggers 3 times. – Switch triggers to short travel mode, then press them fully 3 more times. – Press View to exit. – LED1 and LED3 will stay solid for 5 seconds before powering off. · Gyroscope Calibration – Power off the controller and place it on a flat surface. – Hold View + A + B + Home to enter gyro calibration. – LED1 and LED2 will flash. – After 1 second, press Menu to complete calibration. LEDs will turn off. – Calibration must be performed in XBOX (ABXY) layout mode.

11. Macro Programming (M1/M2 Buttons) – While connected, hold M + M1 or M2 for 3 seconds to enter programming mode. – Press the desired button to assign (e.g., A, B, etc.). – Press M1 or M2 again to save and exit.
Note- : If no button is selected, M1/M2 will be blank. Upto 21 Programmable buttons: A/B/X/Y/D-pad/LB/RB/LT/RT/L3/R3/Menu/View/Joysticks
12. Power Off – Hold the Home button for 5 seconds to power off. – Auto power-off after 10 minutes of inactivity.
13. Controller Reset – Use a small pin to press the Reset hole to restore factory settings.
14. Joystick Force Adjustment (Roller-Based) – The Cosmic Byte Eclipse controller features adjustable joystick tension using a built-in roller mechanism, follow the steps below to customize the joystick force according to your preference:
Adjusting the Joystick Force: – Locate the joystick roller at the base of each analog stick. – To increase joystick resistance, rotate the roller clockwise. – To decrease joystick resistance, rotate the roller counter-clockwise. – Make adjustments gradually and test after each rotation to find your preferred
Note: The roller mechanism allows for fine-tuning of joystick stiffness for better precision or quicker flick response in different game types (e.g., FPS vs Racing).
15. Battery Indicator Guide · Low Battery: Logo light flashes red once every 10 minutes · Charging: Logo light breathes green · Fully Charged: Logo light turns off

אָפּלאָדירן רירעוודיק אַפּ
Download and install the “KeyLinker” App from the Google Play Store or Apple App Store for advanced customization and controller adjustments.
טראָובלעשאָאָטינג
Q1: My controller is not turning on. What should I do? A: The battery might be completely drained. Please charge the controller using the prov ded USB Type-C cable for at least 30 minutes. If it still doesn’t power on, try using a different USB port or cable to verify the power source.
Q2: The controller is not connecting through Bluetooth. How can I fix it? A: Make sure the mode switch is set to Bluetooth (Left position). Press and hold the Pairingbutton for 3 seconds until the logo indicator flashes rapidly. On your device, enable Bluetooth and select “Xbox Wireless Controller.” If the controller still doesn’t connect, delete any old pairing entries, then try again. If the issue persists, use a small pin to press the Reset hole and retry pairing.
Q3: The controller is not connecting in 2.4G wireless mode. What should I do? A: Ensure the 2.4G receiver dongle is properly inserted into the device’s USB port (avoid USB hubs). Switch the mode toggle to 2.4G (Middle position). Hold the Pairing button for 3 seconds — when the logo light turns solid and the controller vibrates, the connection is complete.
Q4: The controller doesn’t vibrate during gameplay. A: Vibration may be turned off or set to 0%. Hold M + Right Stick Up to increase the vibration intensity. If vibration still doesn’t work, reconnect the controller and check again.
Q5: My joysticks are drifting or not responding properly. A: Perform a Stick & Trigger Calibration: Hold View + M + Menu for 3 seconds rotate both sticks clockwise 3 full turns fully press both triggers 3 times press View to exit. If movement feels too stiff, reduce joystick resistance by rotating the joystick roller counter-clockwise.

Q6: The triggers (LT/RT) are not functioning correctly. A: Check the Trigger Mode Switch on the back and toggle between long and short travel modes. Re-run the Stick & Trigger Calibration to re-align trigger response.
Q7: Some buttons are not working or behave oddly. A: Turbo or macro may be active. Cancel turbo by pressing M + A a third time. To clear macros, hold M + M1/M2 for 3 seconds and exit without assigning any key.
Q8: The controller LEDs are flashing continuously or behaving erratically. A: Hold the Home button for 5 seconds to power off. Press the Reset hole once using a pin to restore factory settings. Reconnect the controller in your preferred mode.
Q9: The gyroscope is not responding correctly. A: Ensure the controller is set to XBOX (ABXY) layout. Hold View + A + B + Home to enter gyro calibration. Wait for LEDs 1 and 2 to flash, then press Menu to complete calibration.
Q10: The ABXY buttons don’t match in-game actions. A: Use the ABXY Layout Switch on the back to toggle between XBOX-style and Alternate-style button layouts depending on your game configuration.
Q11: The battery drains quickly. A: High vibration levels or continuous turbo use can reduce battery life. Lower vibration using M + Right Stick Down. Disable turbo when not required to extend playtime.
Q12: I want to restore the controller to its original factory settings. How can I do that?
A: Use a small pin to press the Reset hole on the back of the controller. This will clear all saved configurations and restore factory defaults.

פּראָדוקט ספּעסאַפאַקיישאַנז

ITEM
1. Dimensions 2. Weight 3. Bluetooth Version 4. Battery Capacity 5. Input Voltage 6. Working Current 7. Idle Current 8. Vibration Current 9. Charging Current 10. Charging Time 11. Wireless Range 12. Operating Temperature 13. Humidity Range

דעטאַילס
155 × 102 × 67 mm 225g ± 15g 5.3 1200mAh (11­13 hrs playtime) 5V = 500mA Varies with usage < 20A 50­160mA < 500mA 3­4 hours ~10 meters 0°C ­ 40°C 20% ­ 80% RH

Note: All specifications are for reference and may vary depending on usage and environment. Package Contents
Eclipse Controller × 1 Replaceable D-Pad × 1 2.4G Receiver × 1 USB Type-C Cable (1.5m) × 1 User Manual × 1

SUPPORT DETAILS Customer Care Number: +91 7351615161 (Mon-Sat 10am to 6pm) WhatsApp Support: +91 7351615161 Email: cc@thecosmicbyte.com
וואָראַנטי
The Eclipse Tri-Mode Controller carries 1 year warranty against manufacturing defects only.
Physical, water damage and tampוואָרעד פּראָדוקטן זענען נישט קאַווערד אונטער וואָראַנטי.
Scan the QR Code to know the Warranty Claim Procedure.