הקדמה
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Ikea KALLROR 503.570.02 Stainless Steel Cabinet Handles. Please read these instructions carefully before proceeding with installation to ensure proper and safe use.
פּראָדוקט איבערview
The Ikea KALLROR 503.570.02 handles are designed to offer a modern aesthetic and functional grip for your kitchen cabinets or drawers. This set includes two handles and all necessary screws for a complete installation.
This image displays two sleek, cylindrical stainless steel cabinet handles, along with four silver screws. The handles have a brushed finish, and each handle is shown with two mounting posts. The screws are designed to secure the handles to cabinet doors or drawers.
ספּעסאַפאַקיישאַנז
| מאָדעל נומער | 503.570.02 |
| סאָרט | ייקיאַ |
| Quantity per set | 2 כאַנדאַלז |
| שעפּן לענג | 213 מם |
| שעפּן טיף | 38 מם |
| Hole Spacing (center-to-center) | 160 מם |
| געבויערט לאָך דיאַמעטער | 5 מם |
| פּאַסיק טיר גרעב | 16 מם צו 21 מם |
| Handle/End Cap Material | ומבאַפלעקט שטאָל |
| Plastic Parts Material | פּאָליעטאַלין פּלאַסטיק |
| אַרייַנגערעכנט קאַמפּאָונאַנץ | Installation Hardware (screws) |
| וואָג | 170 גראַמז |
סעטאַפּ און ינסטאַלירונג
Installing your Ikea KALLROR cabinet handles is a straightforward process. Follow these steps carefully for a secure attachment.
פארלאנגט מכשירים
- בויער
- Drill bit (5 mm diameter)
- מעסטן טייפּ אָדער ווירע
- בלייַער
- שרויפנציהער (פיליפּס קאָפּ רעקאָמענדירט)
ינסטאַללאַטיאָן סטעפּס
- מאָס און מארק: Carefully measure and mark the desired position for the handle on your cabinet door or drawer front. Ensure the marks for the two screw holes are precisely 160 mm apart (center-to-center).
- בויער האָלעס: Using a 5 mm drill bit, carefully drill through the cabinet door or drawer front at the marked positions. Ensure the holes are straight and clean.
- צוטשעפּען שעפּן: Align the handle with the drilled holes. Insert the provided screws from the inside of the cabinet door or drawer through the drilled holes and into the handle posts.
- זיכער שעפּן: Tighten the screws firmly with a screwdriver until the handle is securely attached. דו זאלסט נישט אָוווערטייטאַן, as this may damage the cabinet material.
- איבערחזרן: Repeat the process for the second handle if installing a set.
Important: These handles are suitable for door thicknesses between 16 mm and 21 mm. Verify your cabinet door thickness before drilling.
אָפּעראַציע
The Ikea KALLROR cabinet handles are designed for simple and reliable operation. Grasp the handle firmly to open or close cabinet doors and drawers as needed.
וישאַלט
To ensure the longevity and appearance of your stainless steel handles, follow these maintenance guidelines:
- רייניקונג: ווישט רעגולער מיט א ווייכן, דamp cloth. For stubborn marks, use a mild detergent solution. Avoid abrasive cleaners, scouring pads, or chemical solvents, as these can damage the stainless steel finish.
- דרייינג: Always dry the handles thoroughly after cleaning to prevent water spots and maintain their luster.
- דורכקוק: Periodically check the screws for tightness. If a handle feels loose, gently tighten the screws with a screwdriver.
טראָובלעשאָאָטינג
האַנטל איז לויז
If the handle feels loose, gently tighten the screws from the inside of the cabinet door or drawer. Ensure not to overtighten.
שוועריקייט ינסטאָלינג
Ensure the drilled holes are precisely 160 mm apart (center-to-center) and that the drill bit used was 5 mm in diameter. Verify your cabinet door thickness is within the specified 16-21 mm range.
שטיצן
For further assistance or inquiries regarding your Ikea KALLROR cabinet handles, please refer to the official Ikea website or contact Ikea customer service directly.
