Yealink AP08 Digital Signal Processor
Specifications
- Model: AP08
- Interface: USB 3.0 (A – B) Cable, Male Phoenix Connector (Pitch 3.81 mm), RS-232 Connector
- Power Adapter: 3m
- Mounting: Rack mountable (19-inch rack) or wall/table mountable
Package Contents
We recommend that you use the accessories provided or approved by Yealink. The use of unapproved third-party accessories may result in poor performance..
Installation
In a 19-Inch Rack (compliant with the IEC60297 Standard)
- Remove the mounting ear screws from each side of AP08 (2 screws per side).
- Install the mounting ears on both sides of the AP08.
- Push the AP08 into the rack, and fix it to the rack with screws (not included).
Under a Table or On a Wall
Front Panel Introduction
|
1 |
MGMT LED |
• Solid green: Network connected/ transmitting data.
• Off: Network disconnected. • Flashing red: – MGMT LED: Network error. – Dante/LAN LED: Dante module error. |
4 |
RCA LED |
• Solid green: Transmitting signal. • Off: No signal or weak signal level. |
|
2 |
Dante/LAN LED |
5 |
Analog LED |
||
|
3 |
USB LED |
• Solid green: Devices connected. • Off: Devices not connected. |
6 | Status LED | See the next page. |
|
7 |
System Button |
• Quickly press twice within 2 seconds to start Yealink Acoustic Adaptation.
• Press and hold for 5 seconds to reset the device. |
Front Panel Introduction
Status LED
| LED Indicators | Introduction |
|
Solid orange |
• Initializing
• Rebooting |
| Off | Powered off |
| Solid green | In idle status |
| Flash orange slowly | AP08 is upgrading firmware |
| Flash red slowly | AP08 is in recovery mode |
| Flash red quickly | Power error |
| Flash red and green alternately | Searching devices |
Rear Panel Introduction
| 1 | RCA in: 2 RCA inputs for unbalanced analog input. | 7 | RS-232: For device control. |
| 2 | RCA out: 2 RCA outputs for unbalanced analog output. | 8 | USB Type-B: 2 × USB 3.0 ports for device connectivity. |
|
3 |
Analog in: 2 × 3-pin Phoenix connectors for balanced analog input; support 48V phantom power. |
9 |
MGMT: For device control and Management. |
|
4 |
Analog out: 2 × 3-pin Phoenix connectors for balanced analog output. |
10 |
LAN : 3 × RJ-45 ports for Dante Network, with PoE+. |
|
5 |
• GPIO in: 1-8 inputs, analog input, or contact closure (up to 24V) with switchable 5V pull-up.
• GPIO out: 1-8 outputs, open-drain output (up to 24V, 0.3A), default state +3.3V. • +12VDC: 0.1A |
11 |
Power: Universal power input (100–240 V, 50/60 Hz, 2A). |
|
6 |
GND: Earth ground
Connection
Analog in/out Connector
The lines are not included, please purchase separately.
RS-232 Connector
The lines are not included, please purchase separately.
YEALINK (XIAMEN) NETWORK TECHNOLOGY CO., LTD WWW.YEALINK.COM
Declaration of Conformity
We, YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD
- Address: No.666 Hu’an Rd. Huli District Xiamen City, Fujian, P.R. China
- Manufacturer: YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD
- Address: No.666 Hu’an Rd. Huli District Xiamen City, Fujian, P.R. China
- DATE: 29 / July/2024 Declare that the product
- Type: Digital Signal Processor
- Model: AP08 meets the essential requirements and other relevant provisions according to the following EC directive
Directive:
- 2014/30/EU, 2014/35/EU
Conformity
- The product complies with the following standards:
- Safety: EN 62368-1:2020+A11:2020
- EMC:: EN 55032:2015+A11:2020
- EN 55035:2017+A11:2020
- EN IEC 61000-3-2: 2019+A1:2021 EN 61000-3-3: 2013+A1:2019
- Addr No 666 Hu’an Rd Huh DIstrlctXIamen City, Fu]lan, PR
- Te| +86-592-5702OOOI Fax: +86-592-5702455
| Item | Introduction | Download Address |
| Device Calculator | Use this tool to design your deployment based on room type, dimensions, and table. | https://design-tools.ymcs.yealink.com/control-deploy-tool/ |
| Designer | Use this tool for room design, device routing, audio coverage, configuration management, etc. |
https://support.yealink.com/en/portal/docList?archiveType=document&productCode=4b76f1715e9e4cdc |
| Designer User Guide |
Introduce how to use Yealink Room Designer.
|
https://support.yealink.com/en/portal/knowledge/show?id=66553d1743296d7065fddc87 |
| AP08 User Guide | Learn to use AP08 with Yealink Room Designer. | https://support.yealink.com/en/portal/knowledge/show?id=6687684fa5273f35680e510d |
- YEALINK(XIAMEN) NETWORK TECHNOLOGY CO., LTD. Web: www.yealink.com
- Addr: No.666 Hu’an Rd, Huli District Xiamen City, Fujian, P.R.C Copyright©2024 Yealink Inc. All rights reserved.
Frequently Asked Questions
Q: Can I use third-party accessories with AP08?
A: We recommend using accessories provided or approved by Yealink to avoid poor performance. The use of unapproved accessories may result in issues.
Q: What do the different LED indicators on the front panel signify?
A: The MGMT LED indicates network error, the Dante/LAN LED indicates Dante module error, the USB LED signifies data transmission and the Status LED provides system status information.
Documents / Resources
 |
Yealink AP08 Digital Signal Processor [pdf] User Guide AP08, AP08 Digital Signal Processor, AP08, Digital Signal Processor, Signal Processor, Processor |