XTOOL D1 Laser Engravers
Dear XTooler:
Thank you for purchasing xTool DI. We are so grateful for your recognition,and sincerely hope you will enjoy this product!
XTool DI is a high-accCuracy and high-power laser engraver and laser cutter.
From novice to expert, from home use to business, xTool Dl is ready to give you the best laser engraving & cutting experience.
Our mission is to make it easier for everyone to create with our machine.
We attach great importance to product experience and user suggestions.
Please let us know if you have any questions at anytime, we are always here to help. You can join our facebook group which gathers 25000+ innovators like you, to share creative ideas and get inspired by others.
By visiting our online store, you can also find our latest accessories and various materials to maximize the magic of xTool D1.
Thanks again for your support, and we will consistently provide quality products and services in the future.
Sincerely,CEO
Official Website: www.xtool.com
Facebook Group: XTool DI Official Group / Makeblock xTool Official Group
Support Center: support.xtool.com
Technical Support: support@xtool.com
Unbox and check
The secret to getting ahead is getting started.
Are you ready to embark on a creative journey?
Let’s go!
Assemble XTool DI
The screws are used to set the tension of the timing belts. Do not fully tighten them. Otherwise, the timing belts may be damaged.
lf you can’t put the optical shaft through the timing belt, the possible cause is that the timing belt is set too tight. You can adjust its tension by turning the screw.
slide the two sliders down against the front plate.
Fully tighten the two screws.
Pay attention to the front and back sides of the connector. Insert it properly.
No scissors are included in the pack.
Pay attention to the front and back sides of the connectors.
Insert them properly.
The screw is used to set the tension of the timing belt. Do not fully tighten it. Otherwise, the timing belt may be damaged.
80% done!
Excited to see your laser cutter begins to take shape!
Success Is Just around the corner!
Ensure that the cable sleeve is placed in the slot.
Reserve a sufficient length of the cable to allow the laser module to slide between the left and right plates.
Congratulations!
You have completed the installation!
Meet your xTool DI
Set up xTool D1
Adjust the tension of the timing belts
Try to set the timing belts on the right and left plates to the same tension, so that xTool DI can cut and engrave materials properly.
Set the position of the laser module
- Put the focal length setting bar down
- Loosen the thumb screw on the other side and slide the laser module upward or downward
- After determining the position,tighten the thumb screw and put the focal length setting bar back
Download and install software
You can operate xTool D1 by using our official software or the third-party software LightBurn.
Note: You need to purchase LightBurn before using it.
Connect Rotary Attachment
You can connect XTool DI to Rotary Attachment to engrave cylindrical object.
Rotary Attach ment needs to work witha device and software.
For details about how to use it, visit support.xtool.com.
Place Rotary Attachment parallel to the working area of XTool Di.
Before you connect it to xTool D1, you may need to set its level based on the diameter of the material to be processed.
Level reference
Set the level
Use the changing of the level from 3 to 2 as an example.
Documents / Resources
 | D1 Laser Engravers |
References
- User Manualmanual.tools
Where can I get instructions that tell me what the settings have to be like if I want to engrave and cut wood, for example. I just wanted to engrave 3mm wood, I set the power to 50%, but the result is unsatisfactory, you can’t see any letters. The text looks washed out. The border is faint. Can you help me?
Wo kann ich eine Anleitung bekommen, die mir sagt wie die Einstellungen sein müssen, wenn ich z.B. Holz gravieren und schneiden möchte. Ich wollte soeben Holz 3mm gravieren, habe die power auf 50% eingestellt, aber das Ergebnis ist unzufriedenstellend, man sieht keinerlei Buchstaben. Der Text sieht verwaschen aus. Die Umrandung ist schwach. Können Sie mir helfen?
Wo kann ich eine Anleitung bekommen, die mir sagt wie die Einstellungen sein müssen, wenn ich z.B. Holz gravieren und schneiden möchte. Ich wollte soeben Holz 3mm gravieren, habe die power auf 50% eingestellt, aber das Ergebnis ist unzufriedenstellend, man sieht keinerlei Buchstaben. Der Text sieht verwaschen aus. Die Umrandung ist schwach. Können Sie mir helfen?
Where can I find recommended settings for engraving and cutting 3mm wood with the xTool D1, and why is my current engraving washed out and faint?
To achieve clear engraving and precise cuts on 3mm wood with your xTool D1, please check the following hardware and software adjustments:
If the text remains faint after focusing, try decreasing your engraving speed or increasing the lines per cm (density) in your software (Laserbox Basic or LightBurn).
Read the full Q&A page
XTOOL D1 Purchased laserbox insole, connected via USB but not recognized
Please tell me how to resolve
XTOOL D1 購入ごlaserboxインソール、USBにて接続するも認識しない
解決方法を教えてください
Please tell me how to resolve
XTOOL D1 購入ごlaserboxインソール、USBにて接続するも認識しない
解決方法を教えてください
How do I resolve a USB connection issue where the xTool D1 is not recognized by Laserbox software?
If your xTool D1 is not recognized via USB after installing the software, please try the following troubleshooting steps:
For further assistance, you can contact xTool Japan support at 050-5050-9822 or visit support.xtool.com.
Read the full Q&A page
I bought XTOOL D1 Pro20w, but it doesn’t work.
1 When the power is turned on, the marker lights up but the fan does not rotate.
plug.
2 indicator lamp does not change.
What is the normal state when the power is turned on?
XTOOL D1 Pro20ｗを購入ししましたが、作動しません。
１電源を入れた時の状態、マーカーは点灯しますがファンは回りま
せん。
２インジケータランプは、変化しません。
電源を入れた時の正常な状態を教えてください。
1 When the power is turned on, the marker lights up but the fan does not rotate.
plug.
2 indicator lamp does not change.
What is the normal state when the power is turned on?
XTOOL D1 Pro20ｗを購入ししましたが、作動しません。
１電源を入れた時の状態、マーカーは点灯しますがファンは回りま
せん。
２インジケータランプは、変化しません。
電源を入れた時の正常な状態を教えてください。
What is the normal state of the xTool D1 Pro 20W when powered on? My fan does not rotate and the indicator lamp does not change.
Based on the xTool D1 user guide and standard operating procedures for the Pro series, here is the normal state when the power is turned on:
Recommended Troubleshooting Steps:
If the indicator remains unresponsive and the fan does not spin despite the marker being lit, it is highly recommended to contact xTool technical support at support@xtool.com or call their JP support line at 050-5050-9822 as this may indicate a hardware defect.
Read the full Q&A page
mi maquina xtoll no trabaja al ya presionar el boton para que inicie no hace nada
Why does my xTool D1 not start working when I press the start button?
If your xTool D1 does not start after pressing the button, please check the following troubleshooting steps based on the user guide:
If the machine still does not respond, you can contact xTool technical support at support@xtool.com or call +1 (833) 588-4887.
Read the full Q&A page