VORTEX Bike Cadence and Speed Sensor
“
Product Specifications
- Battery: CR2032
- Sensor size: 40 x 30 x 10.7 mm
- Sensor weight: 10 g
- Battery life: over 300 hours
- Waterproof grade: IP67
- Working temperature: -20°C to 50°C
- Wireless: ANT+, Bluetooth
Product Usage Instructions
Quick Setup
Note: Remove the insulation sheet before use.
- Twist the battery door with a coin in the direction shown.
- Take out the insulating sheet and remove the battery.
- Close the battery door and align the arrow with the battery
door to secure it.
XOSS VORTEX uses a CR2032 battery. If you need to replace the
battery, please refer to the above steps.
Download APP
XOSS VORTEX has two working modes: speed and cadence. You can
switch modes using the XOSS APP. Scan the QR code provided to
download the XOSS APP.
SPEED/CADENCE MODE SWITCH
After connecting to the XOSS APP, you can switch between modes,
check battery level, and upgrade firmware. The LED will indicate
the working mode with flashing lights.
Installation
Note: The rubber ring and rubber pad can be selected based on
the installation requirements.
SPEED MODE: Buckle the curved rubber mat onto
the back of the sensor, then secure the sensor with the large
rubber band onto the wheel axle.
CADENCE MODE: Buckle the flat rubber mat onto
the back of the sensor, then secure the sensor with the small
rubber band onto the pedal crank. Ensure the gap between the crank
and frame meets installation requirements.
Frequently Asked Questions (FAQ)
Q: What is the warranty policy for XOSS VORTEX?
A: XOSS VORTEX comes with a one-year free
warranty from the date of purchase. Contact your original dealer
for warranty service. Please note that certain conditions are not
covered by the warranty, including normal aging loss of the
battery, damage or loss due to improper installation, damage from
abnormal use (e.g., high temperature, water damage), and damage
from unauthorized maintenance.
Q: How can I contact customer support for XOSS VORTEX?
A: For any questions or more information, you
can contact XOSS HONG KONG CO., LIMITED at support@xoss.co or visit
their website at xoss.co.
“`
USER MANUAL
XOSS VORTEX
– English-
Product Introduciton
Thank you for choosing XOSS VORTEX
By installing it correctly on the left crank or front hub position, it can accurately measure the cadence or speed data, and support standard ANT+ and Bluetooth protocols. Connecting to APP, Cycling computer or other devices that support Bluetooth and ANT+ protocols can help you Carry out scientific riding training.
Product Accessories
XOSS VORTEX
×1
Rubber Mat flat, curved
×2
Rubber Band(large, small
×2
CR2032 Batteryinstalled
×1
User Manual
×1
XOSS VORTEX
Rubber Mat flat, curved
Rubber Band (large, small
USER MANUAL
XOSS VORTEX – English-
User Manual
– 1 –
Quick Setup
Note:Remove the insulation sheet before use
1. Twist the battery door with a 2.Take out the 3. Close the battery door, coin in direction, open the insulating sheet align the arrow with the
battery door, remove the battery
XOSS VORTEX use CR2032 battery, if you need to replace the battery, please refer to the above steps.
Download APP
XOSS VORTEX has two working modes: speed and cadence, you can switch modes by XOSS APP.
Scan the QR code on the right to download the XOSS APP.
XOSS APP
QR code – 2 –
SPEED/CADENCE MODE SWITCH
After connecting to the XOSS APP, you can switch modes, check the battery level, and upgrade the firmware.
After the product successfully switches the mode, it will flash the LED to indicate the working mode.
Speed mode Cadence mode
If the battery is fully charged, flash the white LED, and if the battery is low, flash the red LED.
Current mode Indicator
– 3 –
Installation
Note: The rubber ring and rubber pad can be selected according to the actual situation.
SPEED MODE Buckle the curved rubber mat onto the back of the sensor, then bind the sensor with the large rubber band onto the wheel axle.
Rubber Mat curved
Rubber Band
CADENCE MODE
Buckle the flat rubber mat onto the back of the sensor, then bind the sensor with the small rubber band onto the pedal crank.
Note: It is necessary to confirm whether the gap between the crank and the frame meets the installation requirements before installation.
Rubber Band
Rubber Mat flat
– 4 –
Product Specification
Battery: CR2032 Sensor size: 40 x 30 x 10.7 mm Sensor weight: 10 g Battery life: over 300hour Waterproof grade: IP67 Working temperature: -20 ~ 50 Wireless: ANT+, Bluetooth
WARRANTY
Thank you for purchasing our product,It has a one-year free warranty from the date of purchase, contact your original dealer for warranty service. The following conditions are not covered by the warranty 1.The normal aging loss of the battery. 2.Damage and loss of products due to improper
installation. 3.Damage caused by abnormal use,such as high
temperature, water damage etc. 4.Damage caused by dismantling by yourself or by
unauthorized maintenance personnel.
XOSS HONG KONG CO., LIMITED ROOMS 1318-9, HOLLYWOOD PLAZA,610 NATHAN ROAD, MONGKOK, KL, HONG KONG Any questions or more information, please contact us via support@xoss.co Visit our website for more products xoss.co
– 5 –
Documents / Resources
 |
XOSS VORTEX Bike Cadence and Speed Sensor [pdf] User Manual VORTEX Bike Cadence and Speed Sensor, VORTEX, Bike Cadence and Speed Sensor, Speed Sensor, Sensor |