FD1 Remote Control Toy Drone
Product Information
Specifications:
- Age: 14+
- Includes: Aircraft, Remote Control, 3 x Batteries, USB Charging
Cable, Propellers, Screwdrivers, Propeller Wrench, Instruction
Manual - Features: Front LED lights, Vehicle Indicator Lights, Mode
selection, Gyroscope calibration
Product Usage Instructions
1. Preflight Preparation – Charging the Drone
Charge the drone using the provided USB charging cable and
connect it to a USB adapter or power bank. Charging time is
approximately 60 minutes. Ensure the battery is fully charged
before flight.
2. Low Battery Warning
If the indicator light on the aircraft flashes during flight and
the remote control beeps, it indicates low battery. Land the
aircraft immediately to avoid losing control.
3. Remote Control Battery Replacement
Open the battery cover on the back of the remote control, insert
three AAA batteries with the correct polarity, and close the cover
securely. Refer to the Battery Safety Guide for detailed
instructions.
4. Flight Battery Removal and Installation
To install the flight battery, push it onto the clips on the
back of the craft until securely installed. To remove, press on
both sides and pull the battery upwards. Ensure proper installation
for safe operation.
5. Gyroscope Calibration
Calibrate the gyroscope by simultaneously pushing the left and
right joysticks to the lower corners until the craft indicator
light flashes and turns to a constant light. The remote control
will beep to indicate successful calibration.
Frequently Asked Questions (FAQ)
Q: How do I know when the drone battery is fully charged?
A: The USB charging cable indicator light will turn green once
the battery is fully charged.
Q: What should I do if I encounter a low battery warning during
flight?
A: When you see the indicator light flashing and hear the remote
control beeping, land the aircraft immediately to prevent loss of
control due to low battery.
Age 14+
FD 1
User Manual
Aircraft
Remote Control
Battery x 3
USB Charging Cable PropelleA/B
Screwdrivers
Propeller Wrench Instruction Manual
-1-
Propeller A Propeller B
Propeller B Power switch
Propeller A Vehicle Indicator Lights
Batteries for aircraft
Front LED lights
The front LED emits a pure white light to show the direction of the vehicle. The v ehicle indicator shows the status of the flight control system.
-2-
Left joystick Right joystick
Power switch/indicator Front trim Left trim
Takeoff and landing Rear trim Right trim
Speed Adhort Press for High-Speed RotationLong Press for Circular Flight
-3-
Headless Mode 360° RollCircular Flight
Mode 1 (Right-hand throttle mode)
To select Mode 1, turn on the remote control’s power switch while holding down the speed button ( ) continuously until the remote control powers on. This will switch to Mode 1.
Left stick
Up
Forward
Right stick
Up
Ascend
Down
Backward
Left
Right
Down
Left
Right
Descend
Turn right
Turn left
Fly left
Mode 2 Mode 2 with left throttle will be the default setting
Fly right
Left stick
Up
Up
Right stick
Up
For
Down
Down
Down
Back
Left
Right
Left
Right
Turn right Turn left
Fly left
-4-
Fly right
Preflight preparation
Charge the Drone
USB Adapter ( 5 V / 1 A )
Power Bank
Connect the drone battery to the USB charging cable. Insert the USB charging cable into the USB charging port of the USB adapter (5V/1A). Charging time: approximately 60 minutes. a. During battery charging, the USB charging cable indicator light will be red. b. Once the battery is fully charged, the USB indicator light will turn green.
Low Battery Warning: During the flight, the indicator light on the aircraft will continue to flash and the remote control will make a “beep” sound to remind you.
Before charging, please read the “Battery Safety Guide” carefully for important instructions! – Use only the original charging cable to charge the battery. – Do not charge the drone’s battery immediately after flight, as the battery temperature may be too high. Wait until the battery cools down to room temperature before charging.
-5-
Preflight preparation
Replace Remote Control Battery
3 x AAA Batteries (Not Included)
Battery Cover Open the battery cover on the back of the remote control, insert three AAA batteries into the battery compartment with the correct polarity, and then close the battery cover to complete the installation.
– Please read the instructions in the “Battery Safety Guide” section of this manual. – When installing the batteries, pay attention to the positive and negative polarity to ensure they are installed correctly.
-6-
Flight Battery Removal and Installation
Installation: Install the battery onto the clips on the back of the craft as shown in the picture and push forward. Make sure the battery is securely installed.
Removal: As shown in the picture above, pull the battery back by pressing on both sides, and then remove the battery upwards.
-7-
Calibrate the gyroscope
Simultaneously push the left and right joysticks to the lower corners of the picture above to calibrate the gyroscopes. The craft indicator light will flash and turn to constant light and the remote control will ‘beep’ to indicate that calibration is complete.
To ensure s table flight, we re commend that the pilot calibrate the gyroscope every time the aircraft is paired and after the crash. Unlock the motor
Simultaneously push the left joystick to the lower right corner and the right joystick to the lower left corner, the motor will rotate and the vehicle will be unlocked.
Pull the left joystick down for 2 seconds and the motor stops rotating. The vehicle is locked
-8-
Take off There are two ways to take off the aircraft. Method 1:
Press the ( ) button briefly and the craft will automatically take off and hover at a height of 1.2 meters. You can control the craft by controlling the joystick. Method 2:
Take off Pick up the flying machine and hold it flat in the palm of your hand as you take off. Gently throw the flying machine into the air and it will hover in the air.
-9-
Landing
When the aircraft is fly ing, short press the ( ) bu tton, and the aircraft will automatically land on the ground
It is essential to keep your craft in visual range at all times. If you can’t see it, you won’t be able to control it properly.
-10-
Speed adjustment
Short press this button
This model has 3 speed modes (low/medium/high). Press and release the ( ) button to toggle between low, medium, and high speed. The remote will “beep” once for low speed and “beep” three times for high speed. (“Tick” twice means medium speed, default speed is low)
High-speed rotation
Short press this button
Short press the ( ) key, the remote control makes a ‘beep’ sound once and the craft starts to rotate rapidly. Press the right joystick in any direction to stop the rotation
-11-
Circular flight
Press and hold this button
Press and hold the ( ) button, the remote control will emit a long ‘beep’ sound, which indicates that the craft has entered the surround flight function, push the right joystick in any direction to exit the surround flight.
360° Roll
10 feet
Short press this button
Once you are familiar with all the functions of the flyer, you can try this amazing tumbling mode. When the craft is at least 1 meter above the ground. Short press the ( ) key, then push the right joystick forward/backward or left/right, the craft will roll in the corresponding direction.
360° tumbling function is better when the battery is fully charged.
-12-
Emergency stop The emergency stop function should only be used in the event of an emergency during flight to avoid any damage or injury.
Press and hold the left and right joysticks down at the same time and the motor will stop immediately. Note: If the craft is far away from you or hits something else at a high speed, you may risk damage to the craft.
After the craft has landed, the craft indicator light will continue to flash. Place the vehicle on a level surface again and pull the left joystick down. Then the craft indicator light changes from blinking to constant light and you can use the craft.
-13-
Headless Mode Headless Mode is a training tool for beginner pilots and is very helpful when the craft is too far away from the pilot (which makes it difficult to judge direction). When you steer the right joystick in these directions, it will fly the airplane forward, backward, left, or right, regardless of which way the front of the airplane’s head is pointing.
During takeoff of the craft, the pilot should be in line with the craft’s head pointing in the same direction.
Short press this button
Input: Briefly press the ( ) button on the transmitter. The aircraft’s indicator light will continue to flash, indicating that the aircraft is in headless mode. Exit: Press the ( ) button on the transmitter again briefly. Then, a single beep sound will indicate that the aircraft has exited headless mode.
-14-
Trimming
Short press this button Front Trim If the craft has a tendency to drift forward:. 1. press the ( ) key once. 2. Wait 2 seconds and observe the movement of the craft. If it still drifts, press the button again 3. Depending on how the craft drifts, it may take several presses to balance the craft 4. Repeat steps 1 and 2 until the craft no longer drifts forward. * You can also fix backward/left/right side drift using a similar method of pressing the trim button. Its adjustment direction is opposite to the drift direction.
The purpose of attitude adjustment is to counteract drift caused by air currents.
-15-
Product Specification
Aircraft Model:FD 1 Weight:31g Maximum Flight Time:8 minutes Motor Model:615 Operating Temperature Range:-10°C to 40°C Size:92*80*32mm
Battery for Flyer Capacity:390mAh Voltage:3.7V Battery Type:Li-ion Polymer Battery charging temperature range:5°C~40°C Charging time:60 minutes (depending on charging rate and remaining battery capacity)
Remote control Flying distance:about 30 meters (outdoor without obstruction) Operating Temperature range:-10.C to 40.C Battery type:3pcs 1.5VAAA batteries(not included)
USB Charging Cable Input:5V/IA Rated power: 5w
-16-
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver . — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
-17-
Documents / Resources
 |
XINZHUO FD1 Remote Control Toy Drone [pdf] User Manual FD1, FD1 Remote Control Toy Drone, Remote Control Toy Drone, Toy Drone |