AA-DC2022-10RF Ceilling Fan Remote Controller
Specifications:
- Receiver Model No.: AA-DC2022-10RF
- Transmitter Model No.: AA24T06-13T4
Product Information:
The Ceiling Fan Remote Controller consists of a receiver with
model number AA-DC2022-10RF and a transmitter with model number
AA24T06-13T4. It is designed to provide convenient control over the
fan and light settings of your ceiling fan.
Installation Instructions:
- Locate a suitable place to install the receiver near the
ceiling fan. - Connect the GND input and output (light) wires as per the
wiring diagram provided. - Connect the GND and output (fan) wires accordingly.
Product Usage Instructions:
Control Instructions:
The transmitter allows you to control both the fan and light
settings of the ceiling fan. Use the buttons on the transmitter to
adjust the speed of the fan and turn the light on or off.
Functions of Receiver and Transmitter:
- GND Input: Connect to the ground wire for
safety. - Output (Light): Connect to the light fixture
of the ceiling fan. - GND: Ground connection for the system.
- Output (Fan): Connect to the fan motor of the
ceiling fan.
FAQ:
Q: How do I pair the transmitter with the
receiver?
A: To pair the transmitter with the receiver,
follow these steps:
- Ensure both devices have fresh batteries.
- Press and hold the pairing button on the receiver until it
starts blinking. - Within a few seconds, press the corresponding button on the
transmitter to complete the pairing process.
INSTALLATION INSTRUCTION FOR CEILING FAN REMOTE CONTROLLER
MODEL NO. OF RECEIVER: AA-DC2022-10RF MODEL NO. OF TRANSMITTER: AA24T06-13T4
IMPORTANT POINTS:
1. Please read this instruction, and save it for further use. 2. Before installation, TURN OFF THE POWER OF YOUR CEILING FAN. 3. Please note that all wiring appliances should be installed by a qualified electrician. 4. This unit is to be used in a 100-120V~ 50/60Hz supply only. (Rating: RECEIVER: Max 50W for fan motor, Max 50W for each lamp. TRANSMITTER: transmitting frequency range: 433.92MHz±300kHz.) 5. Do not install in damp locations or immerse in water. (For indoor use only.) 6. Do not pull on or cut leads shorter. 7. Do not drop or bump the unit. 8. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the transmitter. 9. The batteries must be removed from the transmitter before it is scrapped. And the batteries shall be disposed of safety. 10. The switch shall be mounted at a height greater than 1.7m. 11. The electric shock protection of the RF receiver shall be depended on its installation. 12. The RF remote controller shall be used within its rating range, otherwise overheating and dangerous phenomenon may occur. 13. The RF ceiling fan remote controller is made by XIN HUI A.A. ELECTRONICS LTD. 14. CAUTON: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control. 15. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 16. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 17. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CONTROL INSTRUCTIONS:
1. The receiver is only control by transmitter. 2. If you would like to operate receiver by a new transmitter, you must use the transmitter to code the remote controller. 3. The way of code is within 10s after the receiver is powered on, you should press and hold on the key of “ALL OFF” for 3s to pairing. If code successfully, you will hear a sound “beep” or you will see the light flash 1-3 times. 4. After code successfully, the new transmitter can control the receiver and the old transmitter can not control the receiver.
FUNCTIONS OF RECEIVER AND TRANSMITTER:
ALL OFF: Turn off the light and ceiling fan. FAN ON/OFF: Turn on or turn off the ceiling fan. SPEED+: Increase the ceiling fan speed. SPEED- : Decrease the ceiling fan speed. F/R: Change the ceiling fan direction. NATURE WIND : Turn on the ceiling fan to nature wind mode. LIGHT ON/OFF: Turn on or turn off the light. Delay OFF: Turn off the light and ceiling fan after 5 minutes. Anti theft: Set the receiver to anti-theft mode. Buzzer: Turn on or turn off the Buzzer. 2H: Turn off the ceiling fan after 4 hours. 4H: Turn off the ceiling fan after 4 hours. 8H: Turn off the ceiling fan after 8 hours.
INSTALLATION INSTRUCTIONS: CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER. 1. Make the wiring connection and RF sensor must be stuck inside canopy. 2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy comes up to cover the receiver and bracket. 3. To change the batteries is to open the battery housing cover by sliding out the cover downward to the arrow shown direction while pressing down the cover with thumb. Holder for transmitter: if desired, install onto the wall with screws. 4. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteut/récepteur ecempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Dévelopement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tour brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
GND INPUT
OUTPUT (LIGHT)
GND
OUTPUT (FAN)
Documents / Resources
 |
Xin Hui A A AA-DC2022-10RF Ceilling Fan Remote Controller [pdf] User Manual AA-DC2022-10RF Ceilling Fan Remote Controller, AA-DC2022-10RF, Ceilling Fan Remote Controller, Fan Remote Controller, Remote Controller, Controller |