Iinkqubo ze-WM WM-I3 LTE Cat.M1-NB2 Data Logger
IZIHLANGANISI ZANGAPHAKATHI, IZIHLANGANISO
- Indawo esezantsi ebiyelweyo (iplastiki ye-ABS enokhuseleko lwe-IP67 kunye nemingxuma emi-6 – apho iPCB inokubotshelelwa kwindawo ebiyelweyo ngezikhonkwane emingxunyeni)
- Indawo engaphezulu ebiyelweyo (inobotshelelwa ngezikrufu ezi-4)
- Izikrufu zokulungisa ze-enclosure ukuvala kunye nokutshixa isigqubuthelo esiphezulu se-enclosure
- Ibhetri egcweleyo, ubomi obude (i-Lithium-Thyonyl-Chloride, 3.6V DC, uhlobo lwe-CR14250)
- I-SIM khadi slot (ye-SIM encinci, uhlobo lwe-3FF)
- I-Pulse input cable connector (ukuya kwi-J11) - kwimveliso yemitha ye-pulse (uhlobo lwe-S0)
- Impahla yekhebula etywiniweyo
- Ujongano loqhagamshelo lwebhodi eyongezelelweyo ye-MBus (izikhonkwane ezi-5, eziphawulwe ngu-J17)
- I-Power ON pins (uqhagamshelo lwe-2-pin, yenza mfutshane ukuqala isixhobo, ivumela ibhetri ephawulwe ngu-J5)
- Uqhagamshelwano lwe-eriyali ye-SMA yangaphandle
- Tamper switch (ukwenzela ingqiqo ukususwa komphezulu wesigqubuthelo)* – olu phawu alusebenzi okwangoku
- Izibuko loqwalaselo (izikhonkwane ezi-5, kuqwalaselo lwasekhaya kunye nohlaziyo lwe-firmware, J12)
- MBUS addon board (ukhetho lweodolo)
- Izibuko le-MBUS ukuqhagamshela nayiphi na imitha ye-MBUS ekwaziyo
- Umngxuma wokuvala indawo ebiyelweyo (izikrufu)
- Impahla yokubopha indawo ebiyelweyo (yentsimbi yentsimbi, njl.njl.)
- USB UART Converter
- Intambo yoqwalaselo
Ii-LEDs-ii-LED zokusebenza
UKUNIKEZELWA KWAMANDLA KUNYE NEEMEKO ZOKUSINGQONGILEYO
- Ubonelelo lwamandla: 3.6 VDC
- Igalelo: igalelo lokubetha kwentliziyo (yemveliso yodidi lwemitha ye-S0) / M-Bus (ukhetho)
- Izibuko loqwalaselo: ikhonkco lothotho
- Ukusebenza: -25 ° C ukuya +55 ° C / isitoreji: -40 ° C ukuya +80 ° C, kwi-0-95% rel. ukufuma
- Imilinganiselo: 130x70x40mm (ngeyodwa) / 105x70x40mm (inxalenye ephezulu), Ubunzima: 245gr
- Indawo ebiyelweyo yeplastiki ye-ABS enesigqubuthelo seplastiki esicacileyo, ukhuseleko lwe-IP67
AMANYATHELO OKUFAKA
- Step #1: Remove the enclosure’s plastic top cover (2) by releasing and removing the four 14 screws (3) with a screwdriver.
- Inyathelo #2: Susa imfutshane ye-Power ON uxhumano (8) ukuba ixhunyiwe kwaye ukusebenza kwe-15 yesixhobo kuya kumiswa (ibhetri iya kunqunyulwa).
- Inyathelo #3: Vula isibambi seSIM (5) ukusuka ekunene ukuya ekhohlo kwaye ufake i-SIM khadi (esebenzisa i-APN). Qaphela isalathiso, iSIM khadi kufuneka ifakwe ukusuka kwicala lasekunene ukuya kwicala lebhetri, kwaye i-SIM chip ijonge phantsi, isiphelo esisikiweyo seSIM sijolise kwimodyuli ye-Intanethi yeTelit. Vala ngasemva isiciko sesibambi seSIM.
- Inyathelo #4: Uxhulumaniso lwe-J12 lwe-interface lungasetyenziselwa uqwalaselo lwendawo kunye nokuhlaziywa kwe-firmware ngokusebenzisa intambo yoqwalaselo (17).
- Inyathelo #5: Intambo yoqwalaselo (17) idibanisi emnyama kufuneka ibekwe kwi-WM-I3 enkulu ye-J17 Connection ujongano (izikhonkwane ezi-5), ngokweefoto ezilandelayo. I-pin yoku-1 yokudibanisa emnyama isayinwe ngumqondiso omhlophe, eli cala lekhonkco kufuneka libekwe kufuphi nebhetri (ijoliswe ngakwesobunxele kwisithombeni).
- Inyathelo #6: Ukwenza uqhagamshelo lothotho kwikhompyuter, kufuneka uqhagamshele iadaptha ye-USB UART Converter (16) yentambo yoqwalaselo kwiPC.
- Inyathelo #7: Lungiselela uqwalaselo. Yenza i-pf emfutshane i-Power ON izikhonkwane (nr. 8). Oku kuya kongeza amandla ebhetri kwisixhobo. Emva koko imodem iya kuqalisa ukusebenza kwayo ngokwemimiselo emiselweyo. Isixhobo siya kufumaneka ukulungiselela uqhagamshelo lothotho lwasekuhlaleni.
- Inyathelo #8: Qwalasela iiparamitha zokusebenza kwesixhobo kwizibuko le-USB lasekuhlaleni ngeXesha leWM-E.
- Inyathelo #9: Emva kolungelelwaniso oluphumeleleyo qhawula iadaptha ye-USB (16) kwikhompyuter yakho
kwaye unqanyule intambo yokumisela (17) kwi-J12 ikhonkco (nr. 7). - Inyathelo #10: Khangela ukuba sele uncamathele / unyuse i-eriyali kwisidibanisi se-eriyali yangaphandle (9) yesixhobo.
- Inyathelo #11: Fakela isixhobo kwaye uqhoboshele / ukhwele eludongeni - kufutshane nemitha - okanye ukhwele eludongeni lomngxuma wamanzi okanye umbhobho wamanzi / umbhobho kwi
indawo ezinzileyo ngombhobho clamps. - Inyathelo #12: Qhoboshela i-eriyali yangaphandle yemagnethi kwindawana yentsimbi ukulungisa isigqubuthelo sombhobho – ukuqinisekisa ukuba ineemeko ezingaphazamisekiyo kunye nolwamkelo olwaneleyo lwesignali yenethiwekhi yeselula kwi-eriyali. Ixabiso lomqondiso wangoku linokutshekishwa liXesha leWM-E.
- Inyathelo #13: Icala elichaseneyo lentambo yokufakwa kwepulse (nr. 17 kunye ne-6b) kufuneka ifakwe kwi-pulse output yemitha, ngokungqinelana nentambo yokucofa - umz. PULSE0_0 ukuya kwi-1st meter's pulse output output kunye neGND ukuya ukubekwa phantsi kwegalelo).
Inyathelo #14: Amandla kwisixhobo ngu-nr. Izikhonkwane ezi-8 (yenza imfutshane) njengoko bekuchaziwe ngaphambili. - Inyathelo #15: Buyisela umva isigqubuthelo esingaphezulu sendawo ebiyelweyo (2) uze uqinise ngezikrufu ezine (3).
- Inyathelo #16: Kamva, xa imodyuli yeselula iya kuqaliswa kwaye i-SIM ibonakala ilungile kwaye izicwangciso ze-APN ziqwalaselwe ngokufanelekileyo, isixhobo siya kukwazi ukuxhuma kwinethiwekhi yeCat.M/Cat.M (NB-IoT) kwaye uthumele idatha yosetyenziso olubaliweyo (i-pulse count okanye idatha ye-MBUS).
KUBALULEKILE! Kukwayimfuneko ukuba ube namandla ophawu olufanelekileyo lwenethiwekhi yeselula kwindawo yokusebenza/isiza. Ungayitshintsha indawo ye-eriyali kwindawo ukuze ube nophawu olungcono. Kunxibelelwano oluyimpumelelo lwesixhobo, kufuneka uqwalasele useto lwe-APN yekhadi leSIM esebenzayo (njengekhowudi ye-PIN, i-APN, igama lomsebenzisi kunye negama lokugqitha) kunye namaxesha okugcina idatha, i-NB-IoT yokudlulisa idatha kunye nendlela yedatha. ukuthumela (imo, inkqubo, izibuko leseva, idilesi ye-IP yomncedisi) kunye nomlinganiselo othile/izicwangciso ezinxulumene nemitha. Landela la manyathelo oqwalaselo alandelayo.
UKUSETYENZISWA KWEPARAMETER
- Inyathelo #1: Imodem inokumiselwa kwizibuko lesiriyeli lendawo nge-WM-E Term® software ekufuneka yenziwe phambi kokusebenza okuqhelekileyo kunye nokusetyenziswa. (Ubumbeko olukude lwesixhobo lunokwenzeka ngemiyalezo ye-MQTT. Kufuneka uqwalasele iseva ye-MQTT kutshintshiselwano lwedatha.)
- Inyathelo #2: Kuqwalaselo kunye novavanyo lwesixhobo WM-I3 uya kufuna i APN esebenzayo, SIM khadi esebenzayo.
- Inyathelo #3: Microsoft® .Net Framework v4 kufuneka ifakwe kwikhompyuter yakho. Kwimeko yokulahleka kweli candelo, kufuneka uyikhuphele kwaye uyifake kumenzi webindawo: https://www.microsoft.com/en-us/download/details.aspx?id=30653
- Inyathelo #4: Qhagamshela i-dongle ye-USB kwaye ukhuphele umqhubi kumenzi webindawo:
https://www.silabs.com/developers/usb-to-uart-bridge-vcp-drivers Khetha i-CP210x Universal Windows Driver kwiphepha kwaye ukhuphele ulwandiso lwe-ZIP file. Khipha icinezelwe i file kwindawo kwi-hard drive yePC yakho. - Inyathelo #5: Vula iPhaneli yoLawulo yeWindows kunye noMphathi wesiXhobo. Apho kwicandelo Ezinye izixhobo uya kufumana i-CP210x USB kwisilawuli se-UART Bridge okanye ukungena okufanayo.
Cofa imouse ekunene nqakraza kwingeniso kwaye ukhethe i Hlaziya ukhetho lomqhubi. Khangela kulawulo lomqhubi okhutshiweyo (.zip file) kwaye ukhethe ulawulo kwaye utyhale kwi Lungile. Emva koko umqhubi uya kufakwa.
- Inyathelo #6: Iphaneli yokulawula / uMphathi weSixhobo uya kudwelisa i-USB kwibhulorho ye-UART. Jonga inombolo yesibuko seCOM! Qaphela ukuba kufuneka usebenzise le nombolo yezibuko le-COM ngexesha loqwalaselo kwi-software yeXesha le-WM-E!
- Inyathelo #7: Ngoku khuphela isoftware yoqwalaselo lweXesha leWM-E kweli khonkco: https://m2mserver.com/m2mdownloads/WM_ETerm_v1_3_78.zip Kufuneka ube namalungelo omlawuli kulawulo apho usebenzisa inkqubo.
- Inyathelo #8: Khupha i.zip file kuluhlu kwaye wenze iWM-ETerm.exe file. Kufuneka ube namalungelo omlawuli kulawulo apho ufakwe khona.
- Inyathelo #9: Isoftware yoqwalaselo iya kuqaliswa. Cofa kwiqhosha lokuNgena (shiya igama lomsebenzisi kunye negama lokugqitha imihlaba njengoko izaliswe). Emva koko khetha i WM-I3 ngokucofa i Khetha iqhosha.
- Inyathelo #10: Khetha uhlobo loQhagamshelwano kwicala lasekhohlo lesikrini, emva koko ukhethe i Uthotho tab. (Kwimeko yoqhagamshelo lwe-LwM2M, khetha i-LwM2M tab.)
Emva koko yongeza igama elitsha loqhagamshelwano leprofile emva koko cofa kwi Yenza iqhosha. - Inyathelo #11: Kwifestile elandelayo useto loqhagamshelo luya kudweliswa. Apha khetha i-port ye-COM ekunene ngokwenombolo ye-USB ekhoyo (i-serial) ye-port. (Kuqhagamshelwano lwe-LwM2M seta idilesi ye-IP, i-Port kunye ne-Endpoint name.) Emva koko nqakraza kwi Gcina iqhosha ukugcina uqhagamshelwano lwepro.file.
- Inyathelo #12: Kwiscreen esikhulu, kwicala elisezantsi lasekhohlo, khetha uqhagamshelo olugciniweyofile kwi Nceda khetha umdibaniso!
- Inyathelo #13: Vula iParameters funda i icon kwimenyu yesikrini ukuze ufunde iiparamitha zokusebenza kwesixhobo.
- Inyathelo #14: Inkqubela phambili yesixhobo sokufunda iparamitha inokujongwa kwicala lasekunene ezantsi kwesikrini kwibar yenkqubela. Inkqubo iya kulayisha uluhlu kwaye ifunde amaxabiso eparameter kwiscreen.
- Inyathelo #15: Khetha iparameter yesethingi yenethiwekhi yeSelula. Tyhila i Hlela amaxabiso iqhosha kwicala lasekunene, ngoko onke amasimi eparameter anamaxabiso aya kulayishwa kwikhusi. Qwalasela iiparamitha zemodem ngokweemfuno: APN – APN yeSIM khadi yokuqhagamshela kuthungelwano lweNarrow Band, igama lomsebenzisi APN kunye negama lokugqitha lomsebenzisi APN – ukuba kuyimfuneko, iPIN yeSIM – (ukuba isebenzisa ikhowudi yePIN). Cofa kwi Gcina iqhosha.
- Inyathelo #16: Khetha iDatha yokuthumela useto lweqela lepharamitha. Cofa i Hlela amaxabiso iqhosha kwicala lasekunene, kwaye uqwalasele: Idilesi ye-IP yomncedisi - Idilesi ye-IP yomncedisi, i-port ye-server, i-Data yokuthumela ikhefu, i-protocol yendawo (khetha kwi-GRF (i-Grafana), i-TCP, i-LwM2M okanye i-MQTT), ukugcinwa kwedatha rhoqo, Umjikelo wokugcinwa kwedatha ubalwa ngo (isiseko sohlengahlengiso lwexesha – ixesha lokusebenza kwesixhobo okanye i-GMT). Kubalulekile ukuchaza idilesi ye-IP yeseva ye-NTP kunye neSibuko sokufumana ixesha ledatha engenayo. Emva koko cofa kwi Gcina iqhosha.
- Inyathelo #17: Khetha i-Alarm meter useto lweqela leparamitha kwaye uqwalasele iparameters ngokwemitha oyiqhagamshelweyo. Emva koko cofa kwi Gcina iqhosha.
- Inyathelo #18: Ukuba usebenzisa uqhagamshelo lwe-M-Bus, ngoko khetha i-MBUS yeqela lepharamitha yeqela kwaye uqwalasele iparameters. Emva koko cofa kwi Gcina iqhosha.
- Inyathelo #19: Ukuba ufuna ukusebenzisa isaziso se-alam, emva koko khetha i-Alarm ingxelo useto lweqela lepharamitha kwaye uqwalasele iiparamitha. Emva koko ucofe ku Gcina.
- Inyathelo #20: Xa ugqibile uhlengahlengiso lweparameter, tyhala uye kwiParameters bhala icon kwimenyu. Emva koko lonke uluhlu lweparameter kunye namaxabiso alo aya kuthunyelwa kwisixhobo se-WM-I3®. Isalathisi senkqubela phambili esezantsi siya kubonisa ubume benkqubo.
- Inyathelo #21: Ukufumana isatifikethi okanye ukufakwa kwesatifikethi se-CA, nceda ufunde iNcwadi yoMsebenzisi.
Ukufumana ezinye iinketho zoqwalaselo, funda iincwadana, nceda:
- Incwadi yokusebenzisa: https://www.m2mserver.com/m2m-downloads/User_Manual_for_WM-I3_v1_90_EN.pdf
- Inkcazo yoqwalaselo ye-MQTT inokufumaneka apha:
https://www.m2mserver.com/m2m-downloads/MQTT_Protocol_Description_for_WM-I3_v1_80_EN.pdf - Inkcazo yoqwalaselo lwe-LwM2M:
https://www.m2mserver.com/m2m-downloads/User_Manual_for_WMI3_LwM2M_Settings_v1_80_EN.pdf
Unako kwakhona ukukhuphela sample uqwalaselo files:
- Sample WM-I3 uqwalaselo file (TCP, LwM2M kunye ne-MQTT ziyahambelana):
https://www.m2mserver.com/m2m-downloads/WM-I3_Sample_Config.zip
AMAXWEBHU & NENKXASO
Iimanyuwali ziyafumaneka kwithu webindawo: https://m2mserver.com/en/product/wm-i3/
Inkxaso yemveliso inokucelwa nge-imeyile: iotsupport@wmsystems.hu
Le mveliso iphawulwe ngesimboli se-CE ngokwemigaqo yaseYurophu.
Isimboli somgqomo ohlatyiweyo sithetha ukuba imveliso ekupheleni komjikelo wobomi bayo kufuneka ilahlwe nenkunkuma yasekhaya ngokubanzi kwiManyano yaseYurophu. Lahla kuphela izinto zombane/ze-elektroniki kwiinkqubo zokuqokelela ezahlukileyo, ezilungiselela ukufunyanwa nokuhlaziywa kwezinto eziqulethwe ngaphakathi. Oku akubhekiseli kuphela kwimveliso, kodwa nazo zonke ezinye izixhobo eziphawulwe ngesimboli esifanayo.
Amaxwebhu / Izibonelelo
 |
Iinkqubo ze-WM WM-I3 LTE Cat.M1-NB2 Data Logger [pdf] Isikhokelo soFakelo I-WM-I3 LTE Cat.M1-NB2 Data Logger, WM-I3, LTE Cat.M1-NB2 Data Logger, Data Logger, Logger |
