Imodem ye-WM-E8S® – IsiKhokelo esiKhawulezayo seReference
IIPROPATI ZONXIBELELWANO
- Imodem ye-WM-E8S yangaphandle yendalo yonke i-modem ye-AMR ecacileyo kunye ne-4G LTE / 2G okanye i-LTE Cat.M / Cat.NB / 2G izakhono zokufunda ngokuzenzekelayo kweemitha zombane. Imodem inokudityaniswa kulo naluphi na uhlobo lwemitha.
- Imodyuli yeselfowuni: ngokohlobo lwemodyuli ye-intanethi ekhethiweyo (jonga i-Datasheet)
- Isibambi sekhadi le-SIM (i-SIM enokuthathelwa indawo yi-push-insert, uhlobo lwe-2FF)
- Ujongano lwe-eriyali yangaphandle: SMA-M (50 Ohm)
IINKONZO
- AC/DC isidibanisi igalelo amandla ~ 85..300VAC / 100..385VDC – ibhloko terminal
- I-RS232 + RS485 port (i-RJ45 isidibanisi, i-wiring inokucelwa njenge-2- okanye i-4-wire)
- I-RS485 enye izibuko (i-2 okanye i-4-wire) - i-terminal block connector
- I-CL (i-loop yangoku, i-IEC1107 Mode C) - i-terminal block connector
- DI (amagalelo edijithali ama-2 / amagalelo anengqiqo) – isiqhagamshelanisi sebhloko ye-terminal
- Iinketho zokuodola:
- RS485 enye indawo / izibuko lesibini (2-ingcingo, terminal block isiqhagamshelanisi)
- okanye ujongano lwe-Mbus (isidibanisi sebhloko yesiphelo) – Mbus master for max. 4 ikhoboka
*Endaweni yokuzikhethela, enye indlela ye-RS485 isiqhagamshelanisi esiboniswe emfanekisweni, imodem inokuodolwa ngojongano lwe-Mbus nayo.
NGOKU, UKUSETYENZISWA
- Imodem inokuthi inikwe amandla kwi-AC/DC igalelo lokudibanisa amandla
- Unikezelo lwamandla: ~ 85..300VAC (47-63Hz) / 100..385VDC
- Okwangoku (i-stand-by): 20mA @ 85VAC, 16mA @ 300VAC / (I-Avareji) 25mA @ 85VAC, 19mA @ 300VAC
- Ukusetyenziswa kwamandla: Umyinge: 1W @ 85VAC / 3.85W @ 300VAC
UYILO & UKWAKHIWA
- IP52 ebiyelweyo yeplastiki (ngokwe-DIN 43861 inxalenye yesi-2) enesigqubuthelo sebhloko esiselubala (ukukhusela amazibuko)
- 6 ukusebenza kwe-LEDs
- Ubushushu bokusebenza: phakathi -25 ° C kunye +70 ° C, kwi-0 - 95% rel. ukufuma / Ukugcinwa: phakathi -40 ° C kunye +80 ° C, kwi-0 - 95% rel. ukufuma
- Imilinganiselo (W x L x H) / Ubunzima: 175 x 104 x 60 mm / 400gr
IIMPAWU EZIPHAMBILI
- Imodem yangaphandle yendalo yonke, iyahambelana naluphi na uhlobo lwemitha
- Ukhuseleko lokunyuka (ukuya kuthi ga kwi-4kV) - ukhetho lwe-odolo
- Tamper switsha yokukhangela isigqubuthelo sivuliwe
- Supercapacitor ukhetho (ukwenzela amandla outages)
UKUSEBENZA
- Unxibelelwano oluselubala
- Isaziso se-alam kwangoko (ukulahleka kwamandla, utshintsho lwegalelo)
- Ukude kunye nohlaziyo lwefirmware ekhuselekileyo
- Uqwalaselo: WM-E Term software; ngokuzikhethela nguManejala weSixhobo® isoftwe
RJ45 UQHAGAMSHELO LWE-INTERFACE
Sebenzisa i-RJ45 isidibanisi kuqhagamshelo lwemitha (RS232 okanye RS485) kunye noqwalaselo olusuka kwiPC.
- Uqhagamshelo lwe-RS232 yothotho:
Yenza uqhagamshelo lweserial ukusuka kwimodem ukuya kwiPC okanye imitha ngocingo RJ45 isidibanisi Pin #1, Pin 2, kunye Pin #3 – optionally pin nr. #4.- I-PIN #1: GND
- I-PIN #2: RxD (ukufumana idatha)
- I-PIN #3: TxD (ithumela idatha)
- I-PIN #4: DCD
- RS485 2- okanye 4-uqhagamshelwano ngocingo:
Qwalasela imodem yoqhagamshelo lwemitha ye-RS485-imowudi yocingo olu-2 okanye olu-4:- I-PIN #5: i-RX/TX N (-) - ye-2-wire kunye ne-4-wire connection
- I-PIN #6: i-RX/TX P (+) - ye-2-wire kunye ne-4-wire connection
- I-PIN #7: TX N (-) – yoqhagamshelwano lweengcingo ezi-4 kuphela
- I-PIN #8: TX P (+) - yoqhagamshelwano lwe-4-wire kuphela
AMANYATHELO OKUFAKA
- Inyathelo #1: Kwimo yokucima amandla, qinisekisa ukuba isigqubuthelo setheminali seplastiki (esiphawulwe ngokuthi "I") sibekwe kwindawo ebiyelweyo yesixhobo ("II") phambi kokuba uqhubeke!
- Inyathelo #2: I-SIM khadi esebenzayo (uhlobo lwe-2FF) kufuneka ifakwe kwimodem yomphathi weSIM. Qaphela isalathiso sofako (landela iingcebiso zefoto elandelayo). Indlela eyiyo/indlela efanelekileyo yeSIM inokubonwa kwisitikha semveliso.
- Inyathelo #3: Qhagamshela intambo yesiriyali eneentambo kwisidibanisi se-RJ45 (RS232) ngokutsho kwepinout kwiphepha elidlulileyo.
- Inyathelo #4: Qhoboshela i-eriyali ye-LTE yangaphandle (800-2600MHz) kwisidibanisi se-eriyali ye-SMA.
- Inyathelo #5: Yongeza ~ 85-300VAC okanye 100-385VDC amandla voltage kwi-AC/DC enesihloko isiqhagamshelanisi kwaye isixhobo siya kuqalisa ukusebenza kwaso ngoko nangoko.
ISILUMKO!
Nceda uqwalasele oku kulandelayo, ~ 85-300VAC okanye 100-385VDC ingozi yokutshatyalaliswa kombane ngaphakathi kwendawo ebiyelweyo!
SUKUvula indawo ebiyelweyo kwaye UNGAYIchukumisi i-PCB okanye iindawo zayo zombane!
Isixhobo kufuneka sisetyenziswe kwaye siqhutywe ngokuhambelana nencwadana yomsebenzisi ehambelanayo. Ufakelo lunokwenziwa kuphela ngumntu onoxanduva, ofundiswe kwaye onobuchule liqela lenkonzo, onamava okwaneleyo kunye nolwazi malunga nokuqhuba i-wiring kunye nokufaka isixhobo semodem. Akuvumelekanga ukubamba okanye ukuguqula iingcingo okanye ukufakwa komsebenzisi.
Akuvumelekanga ukuvula indawo ebiyelweyo yesixhobo ngexesha lokusebenza kwayo okanye phantsi koqhagamshelo lombane.
* Endaweni yokuzikhethela, enye indlela ye-RS485 isiqhagamshelanisi esiboniswe emfanekisweni, imodem inokuodolwa ngojongano lwe-Mbus nayo.
IIMPAWU ZE-LED (ukusuka ekhohlo ukuya ekunene)
- I-LED 1: Imo yenethiwekhi yeselula (ukuba ubhaliso lwenethiwekhi yeselula luphumelele, luya kudanyaza ngokukhawuleza)
- I-LED 2: Imo ye-PIN (ukuba iyalayita, ke imeko ye-PIN ilungile)
- I-LED 3: Unxibelelwano lwe-E-meter (isebenza kuphela nge-DLMS)
- I-LED 4: I-E-meter relay status (engasebenzi) - isebenza kuphela nge-M-Bus
- I-LED 5: Isimo se-M-Bus
- I-LED 6: Ubume beFirmware
UQINISEKISO
Imodem inenkqubo efakwe ngaphambili (i-firmware). Iiparamitha zokusebenza zingaqwalaselwa kunye ne-software ye-WM-E Term II (ngokusebenzisa i-RJ45 ikhonkco kwi-RS232 okanye i-RS485 mode).
- Inyathelo #1: Khuphela isoftware yoqwalaselo ye-WM-E kwikhompyuter yakho ngeli khonkco:
https://m2mserver.com/m2m-downloads/WM_ETerm_v1_3_80.zip - Inyathelo #2: Khupha i.zip file kuluhlu kwaye wenze iWM-ETerm.exe file. (IMicrosoft .Net Framework v4 kufuneka ifakwe kwikhompyuter yakho ukuze isetyenziswe).
- Inyathelo #3: Ngena kwisoftware ngezi khredithi zilandelayo:
Igama lomsebenzisi: Umlawuli / Igama lokugqitha: 12345678
Cofa kwiqhosha lokuNgena ukungena kwisoftware. - Inyathelo #4: Khetha i WM-E8S kwaye tyhala uye Khetha iqhosha apho.
- Inyathelo #5: Kwicala lasekhohlo lesikrini, cofa kuQhagamshelwano uhlobo lwethebhu, khetha ujongano lweSerial.
- Inyathelo #6: Yongeza igama leprofile kwindawo entsha yodibaniso kwaye tyhala kwi Yenza iqhosha.
- Inyathelo #7: Kwifestile elandelayo useto loqhagamshelo luya kuvela, apho kufuneka uchaze unxibelelwano lweprofile iiparamitha.
- Inyathelo #8: Yongeza i-port ye-COM yokwenyani yoqhagamshelo lwesixhobo ngokwe-port (s) ye-serial ekhoyo, izinga le-Baud kufuneka libe yi-9 600 bps okanye ngaphezulu, ifomathi yeDatha kufuneka ibe yi-8,N,1.
- Inyathelo #9: Cofa kwi Gcina iqhosha ukugcina unxibelelwano lweprofile.
- Inyathelo #10: Khetha uqhagamshelo lwe-Serial olugciniweyofile ezantsi kwesikrini ukudibanisa kwimodem phambi kokufunda okanye uqwalaselo!
- Inyathelo #11: Cofa kwi Parameters Funda icon kwi menu ukufunda ngaphandle idatha kwimodem. Onke amaxabiso eparameter aya kuthi emva koko afundwe kwaye abonakale ngokukhetha iqela leparameter. Inkqubela phambili iya kusayinwa yibha yesalathisi ezantsi kwesikrini. Ekupheleni kokufunda tyhala kwiqhosha elithi OK.
- Inyathelo #12: Khetha iqela leparameter ye-APN, kwaye ucofe i Hlela izicwangciso iqhosha. Yongeza ixabiso legama lomncedisi we-APN, ukuba kuyimfuneko ukunika igama lomsebenzisi we-APN kunye nexabiso lokugqitha le-APN kwaye utyhale kwiqhosha elithi Kulungile.
- Inyathelo #13: Emva koko khetha i M2M iqela lepharamitha, kwaye ucofe i Hlela useto iqhosha. Kwizibuko lokufunda imitha eNgaphandle (IEC), nika inombolo ye-PORT, apho uzama ukufunda imitha. Yongeza le nombolo ye-PORT kuqwalaselo kunye nokhuphelo lwe-firmware, ofuna ukuyisebenzisela iparameterisation ekude yemodem / kwi-firmware exhange engaphaya. Emva koko cofa kwiqhosha elithi OK.
- Inyathelo #14: Ukuba i-SIM isebenzisa ikhowudi ye-PIN, uze ukhethe iqela leparamitha yenethiwekhi yeMobile, kwaye wongeze ixabiso le-PIN ye-SIM apho. Apha ungatshintsha isethingi yebhendi yeFrequency ukuya kwi-4G kuphela okanye i-LTE ukuya kwi-2G (yenqaku lokubuyela umva), njl. Emva koko cofa kwiqhosha elithi OK.
- Inyathelo #15: Ukuqwalasela i-RS232 ye-serial port kunye noseto oluselubala, vula iTrans. / Iqela lepharamitha ye-NTA. Iisetingi zesixhobo esisisiseko ziimowudi eziluncedo ezininzi: imowudi ecacileyo, iMeter port baud rate: ukusuka kwi-300 ukuya kwi-19 200 baud (okanye sebenzisa okungagqibekanga 9600 baud), Fixed 8N1 ifomati yedatha (ngokukhangela ibhokisi kwimitha). Qinisekisa isicwangciso ngeqhosha elithi Kulungile.
Inyathelo #16: Ukuqwalasela iiparamitha zeRS485 - emva kokwenza useto tyhala kwiqhosha elithi Kulungile.- Vula iqela leparamitha yojongano lweemitha zeRS485. Qwalasela imo ye-RS485 kwixabiso elifanelekileyo ngokwenguqulo yentambo esetyenzisiweyo (ye-2-wire okanye i-4-wire ecetyiswayo).
- Kwimeko yokusebenzisa enye indlela i-RS485 yokudibanisa ibhloko ye-terminal, isethingi kufuneka ibe yi-2-wire! (Kungenjalo ayiyi kusebenza.)
- Ukusebenza kwe-RS45 yezibuko le-RJ485 kunye ne-terminal block RS485 interface zihambelana!
- Kwimeko yokusebenzisa imowudi ye-RS232 kuphela, "khubaza" izibuko le-RS485 apha.
- Inyathelo #17 (ukhetho): Ukuba uye wayalela isixhobo ngojongano lwe-Mbus, ukwenzela izicwangciso zezibuko le-Mbus elibonakalayo, khetha Iqela leParameter ecacileyo yeSekondari kwaye ucwangcise imowudi ebonisa ngaphaya yeSekondari ukuxabisa 8E1.
- Inyathelo #18: Xa ugqibile, khetha i icon yokubhala iParameter ukuthumela useto olutshintshileyo kwimodem. Ubume benkqubo yoqwalaselo bunokubonwa ezantsi kwesikrini. Ekupheleni kokulayisha, imodem iya kuqaliswa kwakhona kwaye isebenze ngokwemimiselo emitsha.
Imodem isebenzisa i-TCP port nr. I-9000 yonxibelelwano olucacileyo kunye ne-port nor. 9001 yoqwalaselo. I-MBus isebenzisa i-TCP port nr. I-9002 (isantya sesantya kufuneka sibe phakathi kwe-300 kunye ne-115 200 baud).
Olunye useto lunokufumaneka kwincwadana yomsebenzisi yesoftware: https://m2mserver.com/m2m-downloads/WM-E-TERM_User_Manual_V1_94.pdf
Amaxwebhu emveliso, isoftware inokufumaneka kwimveliso webindawo: https://www.m2mserver.com/en/product/wm-e8s/
IZIQINISEKISO
Imveliso inesatifikethi se-CE / esibomvu kwaye iyahambelana nemigangatho yamazwe aphesheya enxulumeneyo Le mveliso yabelwe isimboli ye-CE ngokwemigaqo yaseYurophu.
Amaxwebhu / Izibonelelo
 |
I-WM SYSTEMS WM-E8S System Communication Solutions [pdf] Isikhokelo somsebenzisi I-WM SYSTEMS WM-E8S Izisombululo zoNxibelelwano lweNkqubo, ii-WM SYSTEMS WM-E8S, izisombululo zoNxibelelwano lweNkqubo, izisombululo zoNxibelelwano, izisombululo |