I-LL-Array 6RGB
INCWADI YOKUSEBENZISA
Inguqulelo 1.0
Ukukhupha Imiyalelo
Funda incwadi phambi kokuSebenza
Msebenzisi othandekayo,
Enkosi ngokukhetha isixhobo sethu, sikholelwa ukuba le mveliso intsha iya kukuzisela ummangaliso ongenamkhawulo kunye nolonwabo. Phambi kokuba usebenzise esi sixhobo, nceda ufunde le ncwadana ngocoselelo, kwaye uyigcine ukuze uyisebenzise kwixesha elizayo.
Isilumkiso seDatha
Nceda uqaphele izilumkiso ezibhalwe ngqindilili eziza kuqinisekisa ukusebenza ngokukhuselekileyo nokugudileyo. Ezi zilumkiso zibalulekile ukusa kumlinganiselo othile.
Ingqalelo! Ibonisa isakhono okanye olunye ulwazi oluluncedo kwiimeko ezikhethekileyo.
Kubalulekile! Ibonisa ulwazi olubalulekileyo ukukhusela abasebenzi kwisiganeko okanye ukwenzakala.
Isilumkiso! Ukuthintela umonakalo okanye ukulimala ekusebenzeni okungalunganga.
ILaser! Iileyibhile ezilumkisa ngokhuseleko lweLaser.
Isilumkiso!
Ukuba intambo yangaphandle eguquguqukayo okanye intambo yale luminaire yonakele, iya kutshintshwa yintambo ekhethekileyo okanye intambo efumaneka kuphela kumenzi okanye i-arhente yakhe yenkonzo.
Izikhuselo, iilensi okanye izikrini ze-ultraviolet ziya kutshintshwa ukuba ziye zonakaliswa ngokubonakalayo kangangokuba ukusebenza kwazo kungasebenzi, kuba ex.ample ngeentanda okanye imikrwelo enzulu.
I lamps iya kutshintshwa ukuba yonakele okanye yonakele ngokufudumeleyo.
I lamps iya kutshintshwa ukuba yonakele okanye yonakele ngokufudumeleyo.
Ukukhupha Imiyalelo
Njengoko ufumana into ekhoyo, ukhuphe ngocoselelo ibhokisi, ujonge imixholo ukuqinisekisa ukuba onke amalungu akwimeko entle. Ukwazisa umthumeli ngokukhawuleza kunye nokugcina izinto zokupakisha ukuze zihlolwe ukuba kukho naziphi na iindawo ezonakalisiweyo ekuthumeni okanye kwisixhobo esonakeleyo. Ukugcina izinto zokupakisha njengobungqina bokuqinisekiswa komthumeli.
Ingqalelo!
Le yunithi ikwimeko egqibeleleyo ngaphambi kokunikezelwa, nceda ujonge zonke izixhobo xa ukhulula iyunithi. Umsebenzisi kufuneka alandele le ncwadana yomsebenzisi ukusebenzisa le yunithi, kwaye uqinisekise ukuba ucacile kulo lonke ulwazi lokhuseleko lwelaser kunye nokusebenza kweyunithi phambi kokuba uyivule. Nawuphi na umsebenzi ongalunganga uya kwenza le yunithi iphume kwiwaranti.
Ukuhamba ngononophelo emva kokuyifumana, ukujonga ukuba kukho nawuphi na umonakalo ovela ekuthumeni, kunye nazo zonke izixhobo ezikuyo.
| NAME | QTY |
| Isibane sokukhanya | 1 |
| Ikhodi yamandla | 1 |
| Incwadi yokusebenzisa | 1 |
Izilumkiso zoKhuseleko lweLaser
Ngokutsho kwe-EN 60825-1: 2014, le mveliso yeyeklasi 3b.
Ukudibana kwamehlo ngokuthe ngqo kunokubangela ukwenzakala.
Le mveliso yeyomboniso we-laser kuphela. Ukukhanya kwe-laser yeklasi ye-3b kufuneka kuqhutywe ngumqhubi wengcali kuphela.
Le nto ibizwa ngokuba yi-laser yokubonisa, ikhupha imitha ene-wavelength spectrum phakathi kwe-400 kunye ne-700nm kwaye ivelisa iziphumo zokukhanyisa kwimiboniso.
Imithetho yokhuseleko lwelaser yamazwe ngamazwe ifuna ukuba iilaser kufuneka zisetyenziswe ngendlela eboniswe ngezantsi, ubuncinane beemitha ezi-3 (9.8 ft) zokwahlula okuthe nkqo phakathi komgangatho kunye nelona kukhanya lisezantsi ngokuthe nkqo. Ukongeza, i-2.5 yeemitha zokwahlukana okuthe tye ziyafuneka phakathi kokukhanya kwelaser kunye nabaphulaphuli okanye ezinye iindawo zoluntu.
Ungaze uqondise umqa welaser ebantwini okanye kwizilwanyana kwaye ungaze usishiye esi sixhobo sisebenza singajongwanga.
Iimfuno ezisemthethweni zokusebenzisa iimveliso zokuzonwabisa ngelaser ziyahluka ngokwamazwe ngamazwe.
Umsebenzisi unoxanduva lweemfuno zomthetho kwindawo/ilizwe lokusetyenziswa.
Isilumkiso! Gwema ukudibana kwamehlo ngokuthe ngqo kunye nemiqadi ye-laser ngexesha lokusebenza, ngakumbi xa imiqadi ye-laser ihleli, okanye ukulimala kwamehlo kunokwenzeka.
Inqaku loKhuseleko loKhuseleko lweLaser
Isilumkiso! Amanyathelo okhuseleko lwelaser ayilwe ngokwemigaqo ethile yemigangatho yokhuseleko yelaser yamazwe ngamazwe echaphazelekayo kwaye inezi zindlela zilandelayo zokhuseleko lwelaser.
Laser key switch: laser ifumaneka kuphela xa isitshixo sivuliwe.
I-Laser Emergency switch: iswitshi yokudibanisa ekude, iya kunqumla indlela yokukhanya kwe-laser ngokukhawuleza nje isixhobo sisengozini enokwenzeka;
Laser inkomba: laser ebonisa ipaneli engaphambili yesibane selaser “laser-ready”
Iileyibhile zokhuseleko lweLaser: umgca oncanyathiselweyo kunye nemigangatho yaseYurophu kwizitikha zokhuseleko lwe-chassis laser ezininzi
Imiyalelo yoKhuseleko
Ukukhusela okusingqongileyo, nceda uzame ukuphinda usebenzise imathiriyeli yokupakisha kangangoko unako.
Iprojektha yeyosetyenziso lwangaphakathi kuphela, IP20. Sebenzisa kuphela kwiindawo ezomileyo. Gcina esi sixhobo kude nemvula kunye nokufuma, ubushushu obugqithisileyo, ukufuma kunye nothuli. Musa ukuvumela ukudibana namanzi okanye naluphi na olunye ulwelo, okanye izinto zesinyithi
Sukulahla le mveliso njengenkunkuma nje jikelele, nceda ujongane nemveliso ulandele ukulahlwa kwemveliso yombane kwilizwe lakho.
Khangela isixholo kwindawo engena umoya, kude kuyo nayiphi na imathiriyeli enokutsha kunye/okanye ulwelo.
Isixhobo kufuneka simiswe ubuncinci be-20cm ukusuka kwiindonga ezijikelezileyo
Ukuze ugweme i-condensation yenziwe ngaphakathi, vumela le yunithi ukuba ivumelane nokushisa okujikelezayo xa ingenisa kwigumbi elifudumeleyo emva kokuthutha. Icondense ngamanye amaxesha ithintela iyunithi ekusebenzeni ngokupheleleyo okanye inokubangela nomonakalo
Musa ukuvala naziphi na iindawo zokungena komoya njengoko oku kunokubangela ukushisa okugqithisileyo.
Musa ukuyifaka kwinto enokutsha.
Musa ukuyisebenzisa xa ubushushu obuphezulu be-ambient bungaphezulu kwama-40 degrees,
Khupha iyunithi xa ingasetyenziswa ixesha elide okanye phambi kokuba utshintshe ibhalbhu.
Musa ukuvula isiciko esiphezulu ukuphepha umonakalo weyunithi.
Nceda usebenzise ukupakishwa koqobo xa isixhobo siza kuthuthwa.
Ungaze uveze i-lens ekukhanyeni kwelanga, nokuba lixesha elifutshane, Oku kunokonakalisa umphumo wokukhanya okanye kubangele nomlilo!
Izilumkiso zoKhuseleko
◆ Njalo uqhagamshela imveliso kwisekethe esekelwe phantsi ukuze ugweme umngcipheko wombane.
◆ Soloko uqhawula imveliso kumthombo wamandla phambi kokuba ucoce okanye utshintshe ifyuzi.
◆ Kuphephe ukuchanabeka kwiliso elithe ngqo kumthombo wokukhanya ngelixa imveliso ivuliwe.
◆ Qinisekisa ukuba intambo yombane ayonakaliswanga okanye yonakele.
◆ Ungaze uqhawule imveliso kumbane ngokutsala okanye ukutsala intambo.
◆ Ukuba ufaka imveliso ngaphezulu, soloko ukhuselekile kwisixhobo sokubopha usebenzisa intambo yokhuseleko.
◆ Qinisekisa ukuba akukho zixhobo ezinokutsha ezikufutshane nemveliso xa usebenza.
◆ Musa ukuyiphatha indlu yemveliso xa isebenza kuba isenokuba shushu kakhulu.
Gcina le Ncwadi yoMsebenzisi ukuze uyisebenzise kwixesha elizayo. Ukuba uthengisa imveliso komnye umsebenzisi, qiniseka ukunika olu xwebhu kumnini olandelayo.
I-Overhead Rigging
Ingqalelo! Ufakelo kufuneka lwenziwe ngenkonzo eqinisekisiweyo yobuqu kuphela. Ufakelo olungafanelekanga lunokubangela ukwenzakala okukhulu kunye / okanye umonakalo kwipropathi. Ukurhwaphiliza okungaphezulu kufuna amava abanzi! Imida yomthwalo osebenzayo kufuneka ihlonishwe, izixhobo zokufakela eziqinisekisiweyo kufuneka zisetyenziswe, isixhobo esifakelweyo kufuneka sihlolwe rhoqo ukwenzela ukhuseleko.
◆ Qinisekisa ukuba indawo engezantsi kwendawo yofakelo ayinabantu abangafunwayo ngexesha lokurhwaphiliza, ukurhwatywa kunye nokusevisa.
◆ Beka isixhobo kwindawo engena umoya, kude kuyo nayiphi na imathiriyeli enokutsha kunye/okanye ulwelo. Isixhobo kufuneka simiswe ubuncinci be-20cm ukusuka kwiindonga ezijikelezileyo
◆ Isixhobo sifanele sifakelwe kwindawo ekude nabantu nangaphandle apho abantu banokuhamba okanye bahlale phantsi.
◆ Isixhobo kufuneka silungiswe kakuhle; i-swinging mounting inobungozi kwaye ayinakuqwalaselwa!
◆ Musa ukuvala nayiphi na indawo yokungena komoya njengoko oku kunokubangela ukufudumeza ngokugqithiseleyo
◆ Ngaphambi kokuba isetyenziswe okokuqala, kufuneka ihlolwe ngabasebenzi abaqeqeshiweyo ukuqinisekisa ukhuseleko, ukuhlolwa rhoqo ngonyaka.
Ngaphambi kokurhweba qinisekisa ukuba indawo yokufakela inokubamba ubunzima besixhobo esiphindwe ka-10. Ukusebenzisa intambo yentsimbi enokuthi ibambe i-12 ubunzima besixhobo, ngokusebenzisa i-eye-bolt yokuncedisa i-installment yokuxhoma.
Amandla e-AC
Nceda usebenzise amandla aqhotyoshelweyo, qaphela ukuba amandla voltage kunye nefrikhwensi ziyafana nomthamo ophawulweyotage kunye nobuninzi besixhobo xa uqhagamshela umbane. Amandla esixhobo ngasinye kufuneka aqhagamshelwe ngokwahlukileyo, ukuze isixhobo sibe nokulawulwa ngabanye.
Inkcazo yentambo:
| Ikhebhula(EU) | Intambo (US) | Iphini | Amazwe ngamazwe |
| Ntsundu | Mnyama | Phila | L |
| Isibane esiluhlaza | Mhlophe | Ngaphakathi | N |
| Mthubi/Luhlaza | Mthubi/Luhlaza | Umhlaba |  |
Ukufakwa kweMveliso
DMX-512 uxhumano
◆ Uqhagamshelwano phakathi kwezibane kunye ne-DMX kufuneka lusebenzise intambo eshiyiweyo yobubanzi obungaphezulu kwe-0.5mm. Nceda usebenzise iplagi/isokethi ye-5 ye-pin XLR eqhotyoshelweyo ukuqhagamshela i-DMX output/input interface. Uqhagamshelo phakathi kwesokethi kunye nentambo njengoko kungezantsi (qaphela iplagi/isokethi ye-5 inombolo yepini kunye nendawo).
◆ Qaphela, iplagi ye-XLR / i-socket ye-5pin ayinakuchukunyiswa yi-hull yangaphakathi, ukudibanisa phakathi kwezikhonkwane akuvumelekanga. Ngaphandle konxibelelwano olungentla, iplagi/socket ye-XLR ayinakudityaniswa nomgca wolawulo we-XLR. Isixhobo sifumana isiginali yolawulo yeDMX512(1990) esemgangathweni.
◆ Xa usebenzisa isignali yokulawula i-DMX512 eqhelekileyo, i-interface yokugqibela yesixhobo kufuneka idibaniswe kwiplagi ye-DMX. Le plug ibeka i-120 ohm ukuxhathisa phakathi kwe-"canon" yeplagi ye-2 pin kunye ne-3 pin. Ibonisa njengomfanekiso ongezantsi. Ukuncamathelisa le plagi kwisixhobo sokugqibela sokuphuma kombane, kuya kuthintela ukuphazamiseka ngexesha lenkqubo yokuhanjiswa komqondiso.
Imiyalelo yokusebenza
| HAYI | Igama | Umsebenzi |
| 1 | Ukuvula iLaser | RGB laser beam (480mW)×6Pcs |
| 2 | Ukuvula kwe-LED | I-LED efudumeleyo emhlophe (3W)×6Pcs |
| 3 | Ungeniso lwamandla(Bule) | Blue neutrik amandla ngaphandle ubeke isokhethi |
| 4 | Igalelo le-DMX | I-5PIN eyindoda ye-XLR interface, yonxibelelwano lwe-DMX |
| 5 | Imveliso yamandla (Mhlophe) | I-socket emhlophe ye-neutrik yemveliso yamandla, qhagamshela kwi-fixtrue elandelayo |
| 6 | Iziphumo ze-DMX | I-5PIN i-interface ye-XLR yowesifazane, yonxibelelwano lwe-DMX |
| 7 | Inkqubo yokupholisa | Iiseti ezi-6 zokupholisa ifeni ngaphakathi/ngaphandle kwenkqubo |
| 8 | Iliso lokhuseleko | Qhoboshela intambo yokhuseleko |
| 9 | Umboniso we-LED | Ukumisela imodeli |
| 10 | Isibiyeli esixhonyiweyo | Ukulungelelaniswa kwe-hang kunye ne-angle |
| 11 | Isitshixo sokutshintsha | Qinisekisa ukuba umntu oqeqeshiweyo usebenzisa |
| 12 | Ubume be-LED obukude | Isilawuli esikude siqhagamshelene silungile |
| 13 | Ubume beLaser LED | Isalathisi sokukhupha iLaser |
| 14 | Ulawulo olukude IN | Qhagamshela kwisilawuli kude okanye iprojektha yelaser yangaphambili |
| 15 | Ulawulo olukude OUT | Qhagamshela kulawulo olukude lwe-IN lweprojektha yelaser elandelayo. |
Kanye emva kwawo onke amandla kwisixhobo, i-VERSION kunye ne-MANUFACTURE INFORMATION iya kuboniswa kwi-monitor ye-LED yephaneli yangasemva. Xa isixhobo sisebenza, i-monitor ye-LED kwiphaneli yangasemva ibonisa imowudi esebenzayo yangoku okanye idilesi ye-DMX yemodi ye-DMX. Ngoncedo lwepaneli yokulawula ye-LED, kulula kakhulu ukuseta kunye nokutshintsha indlela yokusebenza ye. Emva kokusetwa kwakhona kunye nokugcinwa, ulwazi lwemowudi entsha luya kuboniswa kwi-monitor ye-LED kumandla alandelayo.
IMODE Ukukhetha indlela okanye umva kumsebenzi wokugqibela.
NGENA Qinisekisa, ngenisa kwimenyu enzulu. Yicinezele ukugcina imodeli ekhethiweyo okanye ukongeza kwe-DMX yokuqala.
NGUBANI OTHI Ukutshintsha i-DMX yokuqala yokongeza okanye ixabiso lomsebenzi
| Umboniso we-LED | Inkcazo yomsebenzi | |
|
|
 |
I-LASER Auto shows(LA01-LA06) |
 |
Imiboniso ye-LED Auto(LE01-LE07) | |
 |
MIX Auto shows(LL01-LL06) | |
 |
Imiboniso ezenzekelayo | |
 |
Ukuseta isantya sesiphumo.01 yeyona nto icothayo, i-99 yeyona ikhawulezayo | |
|
|
 |
Imiboniso yezandi ye-LASER(LA01-LA06) |
 |
Imiboniso yezandi ye-LED(LE01-LE07) | |
| |
MIX imiboniso yesandi (LL01-LL06) | |
 |
Imiboniso yesandi | |
 |
 |
Imanyuwali |
 |
 |
Ukuseta idilesi yesitishi |
 |
Ukukhetha iindlela zetshaneli ze-DMX | |
 |
 |
Ngena kwimowudi yekhoboka |
 |
 |
Master vumela |
 |
Buyisela useto olungagqibekanga lwasefektri | |
Phawula: Kwimo yesandi, ukulungiswa kuya kucima emva kwemizuzwana ye-5 ngokuzenzekelayo, ukuba akukho mqondiso wesandi kwaye uya kukhanya kwakhona xa isandi sesandi sifunyenwe.
Ummiselo Wokuqala
| IMENU | NGUBANI OTHI | NGENA | ||
| AUT | -LAS | LA01-LA06 | S. 01 ukuya kwi-S. 99, isantya ukusuka kwisantya ukuya kwisantya I-01 icotha kakhulu, i-99 ikhawuleza kakhulu |
Cinezela ENTER ukugcina |
| -I-LED | LE01-LE07 | |||
| -XHUBA | LL01-LL06 | |||
| -AUT | NGOKUZENZAKALELAYO | |||
| SOU | -LAS | Cinezela ENTER ukugcina | ||
| -I-LED | ||||
| -XHUBA | ||||
| -SOU | ||||
| INDODA | UMANU | L.001-L.255 (Ukukhanya kwe-LED) | NGENA | |
| S.000-S.100(Isitrowu se-LED) S. 000: off, S.099: on , S. 100: isound control strobe |
NGENA | |||
| R.001-R.255 (Ukukhanya kwelaser ebomvu) G.001-G.255 (Ukukhanya kwelaser eluhlaza) B.001-B.255 (Ukukhanya kwelaser eluhlaza okwesibhakabhaka) |
NGENA | |||
| F. 000-F. 100(Laser strobe) F. 000: off, F.099: on , F.100: isound control strobe |
NGENA | |||
| DMX | 03CH( d001-d508) 08CH( d001-d504) 24CH( d001-d480) 28CH( d001-d476) 31CH( d001-d465) |
khetha imo yesitishi Cofa u-ENTER ukugcina | ||
| dXXX | d001-dxxx | Seta idilesi yokuqalisa Cofa u-ENTER ukuze ugcine | ||
| SLA | I-SLAV | S. 001 ukuya kwi-S. 255 | Cinezela ENTER ukugcina | |
| SYS | M-EN | Yenza/khubaza inkosi | Cinezela ENTER ukugcina | |
| PHUMULA | Buyisela useto oluhlala lukhona | Cinezela ENTER ukugcina | ||
Imiyalelo yokusebenza kwe-DMX
Esi sixhobo samkela ugcino olukhulu kunye nesantya esiphezulu se-chip, esibhalwe uninzi lwesiphumo esisekwe kwisicelo se-DMX. Ngaphambi kokulawula amanye amajelo e-DMX, nceda uqiniseke ukuba itshaneli ye-1 yayibekwe kwimodi efanelekileyo (ixabiso).
3CH
| Umjelo | Ixabiso | Inkcazo | |
| IMODE ye-CH1 | 000-009 | Blackout | |
| 010-039 | I-Auto Laser kunye ne-LED show | ||
| 040-069 | Auto Laser show | ||
| 070-099 | Umboniso we-Auto LED | ||
| 100-129 | Umboniso oxubeneyo ozenzekelayo | ||
| 130-159 | ILaser yomsindo kunye nomboniso we-LED | ||
| 160-189 | Umboniso weLaser yesandi | ||
| 190-209 | Umboniso ovakalayo we-LED | ||
| 210-255 | Umboniso oxubene nesandi | ||
| CH2 KUZENZAKALELAYO | LASER + LED MBONISO | 000-039 | Auto LED + Laser show #1 |
| 040-079 | Auto LED + Laser show #2 | ||
| 080-119 | Auto LED + Laser show #3 | ||
| 120-159 | Auto LED + Laser show #4 | ||
| 160–199 | Auto LED + Laser show #5 | ||
| 200-255 | Auto LED + Laser show #6 | ||
| LASER MBONISO | 000-039 | Auto Laser show #1 | |
| 040-079 | Auto Laser show #2 | ||
| 080-119 | Auto Laser show #3 | ||
| 120-159 | Auto Laser show #4 | ||
| 160-199 | Auto Laser show #5 | ||
| 200-255 | Auto Laser show #6 | ||
| Umboniso we-LED | 000-039 | Auto LED show #1 | |
| 040-079 | Auto LED show #2 | ||
| 080-119 | Auto LED show #3 | ||
| 120-159 | Auto LED show #4 | ||
| 160-199 | Auto LED show #5 | ||
| 200-239 | Auto LED show #6 | ||
| 240-255 | Auto LED show #7 | ||
| UMBONISO OXHUBEKILEYO | 0-255 | Ayisetyenziswanga | |
| CH3 | 0-255 | Isantya esizenzekelayo | |
8CH
| Umjelo | Ixabiso | Inkcazo |
| CH1 | 000-255 | Zonke ii-LEDs ezikhanyayo |
| CH2 | 000-002 | ii-LEDs |
| 003-249 | Strobe ukusuka kancinci ukuya ngokukhawuleza | |
| 250-255 | Istrobe yokulawula isandi | |
| CH3 | 000-255 | Zonke iilaser ezibomvu zokuqaqamba |
| CH4 | 000-002 | Iilaser ezibomvu ON |
| 003-249 | Strobe ukusuka kancinci ukuya ngokukhawuleza | |
| 250-255 | Istrobe yokulawula isandi | |
| CH5 | 000-255 | Zonke iilaser eziluhlaza ukuqaqamba |
| CH6 | 000-002 | Iilaser eziluhlaza ON |
| 003-249 | Strobe ukusuka kancinci ukuya ngokukhawuleza | |
| 250-255 | Istrobe yokulawula isandi | |
| CH7 | 000-255 | Zonke iilaser eziluhlaza okwesibhakabhaka |
| CH8 | 000-002 | Iilaser eziBlue ON |
| 003-249 | Strobe ukusuka kancinci ukuya ngokukhawuleza | |
| 250-255 | Istrobe yokulawula isandi |
24CH
| Umjelo | Ixabiso | Inkcazo |
| CH1 | 000-255 | #1 Ukukhanya kokukhanya okukhokelela |
| CH2 | 000-255 | #2 Ukukhanya kokukhanya okukhokelela |
| CH3 | 000-255 | #3 Ukukhanya kokukhanya okukhokelela |
| CH4 | 000-255 | #4 Ukukhanya kokukhanya okukhokelela |
| CH5 | 000-255 | #5 Ukukhanya kokukhanya okukhokelela |
| CH6 | 000-255 | #6 Ukukhanya kokukhanya okukhokelela |
| CH7 | 000-255 | #1Ukukhanya kwelaser ebomvu |
| CH8 | 000-255 | #2 Ukukhanya kwelaser ebomvu |
| CH9 | 000-255 | #3 Ukukhanya kwelaser ebomvu |
| CH10 | 000-255 | #4 Ukukhanya kwelaser ebomvu |
| CH11 | 000-255 | #5 Ukukhanya kwelaser ebomvu |
| CH12 | 000-255 | #6 Ukukhanya kwelaser ebomvu |
| CH13 | 000-255 | #1 Ukuqaqamba kwelaser eluhlaza |
| CH14 | 000-255 | #2 Ukuqaqamba kwelaser eluhlaza |
| CH15 | 000-255 | #3 Ukuqaqamba kwelaser eluhlaza |
| CH16 | 000-255 | #4 Ukuqaqamba kwelaser eluhlaza |
| CH17 | 000-255 | #5 Ukuqaqamba kwelaser eluhlaza |
| CH18 | 000-255 | #6 Ukuqaqamba kwelaser eluhlaza |
| CH19 | 000-255 | #1 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH20 | 000-255 | #2 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH21 | 000-255 | #3 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH22 | 000-255 | #4 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH23 | 000-255 | #5 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH24 | 000-255 | #6 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
28CH
| Umjelo | Ixabiso | Inkcazo |
| CH1 | 000-255 | #1 Ukukhanya kokukhanya okukhokelela |
| CH2 | 000-255 | #2 Ukukhanya kokukhanya okukhokelela |
| CH3 | 000-255 | #3 Ukukhanya kokukhanya okukhokelela |
| CH4 | 000-255 | #4 Ukukhanya kokukhanya okukhokelela |
| CH5 | 000-255 | #5 Ukukhanya kokukhanya okukhokelela |
| CH6 | 000-255 | #6 Ukukhanya kokukhanya okukhokelela |
| CH7 | 000-255 | Lonke ulawulo lokukhanya kweLeds |
| 000-255 | Zonke iiLeds strobe ukusuka kancinci ukuya ngokukhawuleza | |
| 000-255 | Zonke iiLeds zishukuma ngesandi | |
| CH8 | 000-255 | #1Ukukhanya kwelaser ebomvu |
| CH9 | 000-255 | #2 Ukukhanya kwelaser ebomvu |
| CH10 | 000-255 | #3 Ukukhanya kwelaser ebomvu |
| CH11 | 000-255 | #4 Ukukhanya kwelaser ebomvu |
| CH12 | 000-255 | #5 Ukukhanya kwelaser ebomvu |
| CH13 | 000-255 | #6 Ukukhanya kwelaser ebomvu |
| CH14 | 000-255 | Zonke iilaser ezibomvu zokulawula ukukhanya |
| 000-255 | Zonke iilaser ezibomvu strobe ukusuka kancinci ukuya ngokukhawuleza | |
| 000-255 | Zonke iilaser ezibomvu zijikeleza ngesandi | |
| CH15 | 000-255 | #1 Ukuqaqamba kwelaser eluhlaza |
| CH16 | 000-255 | #2 Ukuqaqamba kwelaser eluhlaza |
| CH17 | 000-255 | #3 Ukuqaqamba kwelaser eluhlaza |
| CH18 | 000-255 | #4 Ukuqaqamba kwelaser eluhlaza |
| CH19 | 000-255 | #5 Ukuqaqamba kwelaser eluhlaza |
| CH20 | 000-255 | #6 Ukuqaqamba kwelaser eluhlaza |
| CH21 | 000-255 | Zonke iilaser eziluhlaza ulawulo lokuqaqamba |
| 000-255 | Zonke iilaser eziluhlaza zihamba ukusuka kancinci ukuya ngokukhawuleza | |
| 000-255 | Zonke iilaser eziluhlaza zijikeleza ngesandi | |
| CH22 | 000-255 | #1 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH23 | 000-255 | #2 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH24 | 000-255 | #3 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH25 | 000-255 | #4 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH26 | 000-255 | #5 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH27 | 000-255 | #6 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka |
| CH28 | 000-255 | Zonke iilaser eziluhlaza ukulawula ukukhanya |
| 000-255 | Zonke iilaser eziluhlaza zihamba ukusuka kancinci ukuya ngokukhawuleza | |
| 000-255 | Zonke iilaser ezibhlowu zijikeleza ngesandi |
31CH
| Umjelo | Ixabiso | Inkcazo | |
| CH1 | 000-255 | #1 Ukukhanya kokukhanya okukhokelela | |
| CH2 | 000-255 | #2 Ukukhanya kokukhanya okukhokelela | |
| CH3 | 000-255 | #3 Ukukhanya kokukhanya okukhokelela | |
| CH4 | 000-255 | #4 Ukukhanya kokukhanya okukhokelela | |
| CH5 | 000-255 | #5 Ukukhanya kokukhanya okukhokelela | |
| CH6 | 000-255 | #6 Ukukhanya kokukhanya okukhokelela | |
| CH7 | 000-255 | Lonke ulawulo lokukhanya kweLeds | |
| 000-255 | Zonke iiLeds strobe ukusuka kancinci ukuya ngokukhawuleza | ||
| 000-255 | Zonke iiLeds zishukuma ngesandi | ||
| CH8 | 000-255 | #1Ukukhanya kwelaser ebomvu | |
| CH9 | 000-255 | #2 Ukukhanya kwelaser ebomvu | |
| CH10 | 000-255 | #3 Ukukhanya kwelaser ebomvu | |
| CH11 | 000-255 | #4 Ukukhanya kwelaser ebomvu | |
| CH12 | 000-255 | #5 Ukukhanya kwelaser ebomvu | |
| CH13 | 000-255 | #6 Ukukhanya kwelaser ebomvu | |
| CH14 | 000-255 | Zonke iilaser ezibomvu zokulawula ukukhanya | |
| 000-255 | Zonke iilaser ezibomvu strobe ukusuka kancinci ukuya ngokukhawuleza | ||
| 000-255 | Zonke iilaser ezibomvu zijikeleza ngesandi | ||
| CH15 | 000-255 | #1 Ukuqaqamba kwelaser eluhlaza | |
| CH16 | 000-255 | #2 Ukuqaqamba kwelaser eluhlaza | |
| CH17 | 000-255 | #3 Ukuqaqamba kwelaser eluhlaza | |
| CH18 | 000-255 | #4 Ukuqaqamba kwelaser eluhlaza | |
| CH19 | 000-255 | #5 Ukuqaqamba kwelaser eluhlaza | |
| CH20 | 000-255 | #6 Ukuqaqamba kwelaser eluhlaza | |
| CH21 | 000-255 | Zonke iilaser eziluhlaza ulawulo lokuqaqamba | |
| 000-255 | Zonke iilaser eziluhlaza zihamba ukusuka kancinci ukuya ngokukhawuleza | ||
| 000-255 | Zonke iilaser eziluhlaza zijikeleza ngesandi | ||
| CH22 | 000-255 | #1 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka | |
| CH23 | 000-255 | #2 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka | |
| CH24 | 000-255 | #3 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka | |
| CH25 | 000-255 | #4 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka | |
| CH26 | 000-255 | #5 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka | |
| CH27 | 000-255 | #6 Ukuqaqamba kwe-laser eluhlaza okwesibhakabhaka | |
| CH28 | 000-255 | Zonke iilaser eziluhlaza ukulawula ukukhanya | |
| 000-255 | Zonke iilaser eziluhlaza zihamba ukusuka kancinci ukuya ngokukhawuleza | ||
| 000-255 | Zonke iilaser ezibhlowu zijikeleza ngesandi | ||
| CH29 | 000-009 | NA | |
| 010-039 | I-Auto Laser kunye nomboniso weLed | ||
| 040-069 | Auto Laser show | XA USEBENZA KULE Ndlela, 1-28 AMASHASHI AFUMANEKAYO | |
| 070-099 | Auto Led show | ||
| 100-129 | Umboniso oxubeneyo ozenzekelayo | ||
| 130-159 | I-Auto Laser kunye nomboniso weLed | ||
| 160-189 | Auto Laser show | ||
| 190-219 | Auto Led show | ||
| 220-255 | Umboniso oxubeneyo ozenzekelayo | ||
| CH30 | 000-255 | Jonga i-Ch2 ye-3CH imo | |
| CH31 | 000-255 | Isantya sokudlala | |
Ipharamitha yemveliso
| Umzekelo | I-LL-Array 6RGB |
| Amandla eLaser | Bubomvu(638nm/180mW, luzizi) Luhlaza(520nm/100mW, luzizi) Bulu (450nm/200mW, luzizi) |
| Idayamitha yeBeam | 4mm |
| Ukwahlukana kweBeam | <2mrad |
| Ukuhlelwa kweLaser | Udidi IIIb (IEC60825-1) |
| Ukulinganisa amandla e-LED | I-3W efudumeleyo kunye ne-LED × 6pcs |
| I-engile ye-LED yeBeam | 7° |
| Izihlanganisi | 3 iPin XLR DMX ngaphakathi/ngaphandle |
| Ukutya umbane | 100-240V 50/60Hz 60W Max |
| Ukuqhagamshela amandla | Neutrik PowerCon |
| Ubushushu bokusebenza | 10-40°C |
| Umgangatho wokhuseleko | IP44 |
| Imilinganiselo yeMveliso(WxDxH) | 1000×128×117mm (ngaphandle komqheba) |
| Ukusinda okushiyekile | 7.5Kg |
Amaxwebhu / Izibonelelo
 |
UNITY LASERBAR LL-Array 6RGB Laser Array Bar eneMiqadi yeLaser eBomvu kunye neRGB LED Diodes [pdf] Incwadi yokusebenzisa I-LL-Array 6RGB Laser Array Bar eneMiqadi yeLaser eBomvu kunye neRGB yeLED Diode, iLL-Array 6RGB, iLaser Array Bar eneMitha yeLaser eBomvu kunye neRGB yeRGB yeeDiode, iRed Laser Beams kunye neRGB LED Diode, iiBeams kunye neRGB LED Diode, RGB LED Diode , iiDiodes ze-LED, iiDiodes |